• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.539-542
• /
• 2003

We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}m$, the transmittance at the center of pixel and common electrodes is low due to stronger influence of surface anchoring that holds the LC to the initial state than twisting force induced by neighboring LCs. In case of a large cell gap of 4 ${\mu}m$, the influence of surface anchoring force becomes weak so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we conclude that the light efficiency in the device is dependent on the cell gap.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.173-173
• /
• 2010

We proposed viewing angle switchable liquid crystal display(LCD) associated with fringe-field switching (FFS) mode with high aperture ratio characteristic. In the device, single pixel is separated into two regions, named as main pixel for displaying images and sub pixel for viewing angle control. In sub pixel region, add the common electrode on the top substrate and the initial alignment of liquid crystal is Hybrid Alignment Nematic (HAN) state. In conclusion, we suggested that the device has high aperture ratio characteristic because the LC directors are rotated in which viewing angle control region are generated fringe electric field.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.305-310
• /
• 2004

We have studied the optimal phase retardation value of a homogeneously aligned liquid crystal (LC) driven by fringe-field when using the LC with positive dielectric anisotropy. In general, the transmittance of a homogeneous aligned LC cell under crossed polarizer is maximum when a twist angle of LC by in-plane rotation is 45$^{\circ}$ with polarizer and the cell retardation becomes λ/2. However, the device using the LC with positive dielectric anisotropy does not follow this since the degree of rotation of the LC is dependent on electrode position and in addition the LCs tilt up along the fringe-field. At the center of common and pixel electrode, the LC is most twisted around a middle position of a cell whereas at the edge position of pixel electrode, the LC is most twisted near bottom surface of a cell. Consequently, the optimal phase retardation of the device becomes much larger than λ/2 and the transmittance can be described using the combination of the in-plane switching and twisted nematic mode.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.914-922
• /
• 2003

The FFS (fringe-field switching) mode was known to exhibit both a wide viewing angle and high transmittance, especially when using a liquid crystal with negative dielectric anisotropy. We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}$m, the transmittance at the center of pixel and common electrodes is relatively low because effect of surface anchoring that holds the LC to the initial state is larger than that in a large cell gap of 4 .urn such that the LCs in those regions cannot rotate enough. However, in case of a large cell gap of 4 .urn, the effect of surface anchoring becomes relatively small so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we can conclude that the light efficiency is dependent on the cell gap.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.8-15
• /
• 2007

In this paper, we fabricated the field emitter display using oxidized porous polysilicon(OPPS). Their field emission characteristics and the brightness were investigated for each pixel. The OPPS emitter was operated to each pixel using passive matrix for application of large panel display. We set up the proper thickness and width of upper electrode. The fine structure of OPPS was analyzed and the field emission characteristics of each pixel were investigated. As a result of field emission characteristics of different upper electrode thickness and width, we confirmed that the most efficient thickness was 2nm/7nm and increased the emission efficiency over the width of 2.5 mm. Even if field emission characteristics of each pixel was a little different but we confirmed the same leakage current and emission current, emission efficiency at each pixel. The leakage current and emission current was decreased according to the time increases but all of each pixel were uniformly decreased. We confirmed that the brightness of each pixel was not different and the brightness of OPPS field emitter was 700 cd/m2 at the Vps=20 V. Accordingly, the patterned OPPS field emitter can be applied to high quality field emission display devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.456-458
• /
• 2002

On the half area of a pixel, pretilt angle was decreased by UV radiation and two domain TN was induced by the pretilt difference. In this structure, ITO slit was made inside pixel electrode on the TFT substrate to stabilize domain boundaries. The result shows that this structure is more resistant to outside stress and unwanted domain deformation is prevented.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.185-188
• /
• 2006

We studied on the reverse twist near the pixel edge depending on the rubbing direction for the fringe field switching (FFS) mode. Liquid crystal (LC) dynamic and the transmittance near the pixel edge, where the various field directions are generated, depend on the initial rubbing direction because the position of reverse twist is decided by the angle between the electric direction and the LC director at a bias voltage. For example, when the rubbing angle is $7^{\circ}$, the reverse twist appears on the bottom position of the right sharp comer of the pixel edge so that the reverse region exists far away from main active region. But, when the rubbing angle is $-7^{\circ}$, the reverse twist appears on the top position of the right sharp comer of the pixel edge, resulting that the region becomes more close to the main active area and the unstable disclination lines (DLs) easily intrude into the active region. Therefore, it is necessary to keep the reverse twist region far from the active region and it is possible by controlling the rubbing direction in the design of a pixel electrode.

• Journal of Information Display
• /
• v.5 no.3
• /
• pp.18-24
• /
• 2004

Voltage-dependent transmittance characteristics associated with various cell parameters have been studied in-plane switching liquid crystal display when both common and pixel electrodes are transparent. When both electrodes are opaque, the transmittance is related to only the distance (I) between electrodes. However, where transparent electrode is used, it is influenced not only the 1but also an electrode width (w) and rubbing angle. In addition, these factors are related to operating voltage which shows maximal transmittance. To maximize the light efficiency of the cell and obtain low operating voltage, the above-mentioned cell parameters need to be optimized.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.59-62
• /
• 2004

We investigated the effect of Xe content variation on the luminous efficiency of two different sub-pixel types, i.e., segmented electrode in delta color arrayed enclosed sub-pixel (SDE) and conventional stripe barrier type, in an ac plasma display panel through three-dimensional numerical simulations. The conventional cell type was found to have higher VUV generation efficiency as compared with that of SDE structure, but as the Xe content increased, the SDE type showed higher improvements in efficiency due to the lower plasma loss to the barrier walls.

• Journal of Information Display
• /
• v.7 no.1
• /
• pp.35-40
• /
• 2006

Organic light-emitting diode (OLED) display panel using the charge-pump (CP) pixel addressing scheme was fabricated, and the results show that it is applicable for information display. A CP-OLED panel with 64 ${\times}$ 64 pixels consisting of thin-film capacitors and amorphous silicon Schottky diodes was fabricated using conventional thin-film processes. The pixel drive circuit passes electrical current into the OLED cell during most of the frame period as in the thin-film transistor (TFT)-based active-matrix (AM) OLED displays. In this study, the panel was operated at a voltage level of below 4 V, and this operation voltage can be reduced by eliminating the overlap capacitance between the column bus line and the common electrode.