• Corrosion Science and Technology
• /
• v.18 no.5
• /
• pp.196-205
• /
• 2019

Surface modification techniques are known to improve SCC by adding large compressive residual stresses to metal surfaces. This surface modification technology is attracting attention because it is an economical and practical technology compared to the maintenance method of existing nuclear power plants. Surface modification techniques include laser, water jet and ultrasonic peening, pinning and ultrasonic Nano-crystal surface modification (UNSM). The focus of this study was on the effect of ultrasonic amplitude in UNSM treatment on the corrosion properties of Alloy 600. A microstructure analysis was conducted using an optical microscope (OM), scanning electron microscope (SEM) and electron backscattering diffraction (EBSD). A cyclic polarization test and AC-impedance measurement were both used to analyze the corrosion properties. UNSM treatment influences the corrosion resistance of Alloy 600 depending on its amplitude. Below the critical amplitude value, the pitting corrosion properties are improved by grain refinement and compressive residual stress, but above the critical amplitude value, crevices are formed by the formation of overlapped waves. These crevices act as corrosion initiators, reducing pitting corrosion resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.517-524
• /
• 2018

This purpose of this research is to observe the influence of non-condensable gas (NCG) on a horizontal super-hydrophobic aluminum tube and compare it with a bare aluminum tube. To achieve super-hydrophobic characteristics, an aluminum tube was coated with a Self-Assembled Monolayer (SAM). The overall heat transfer coefficient U was used to represent the condensation performance. The NCG mass fraction was the main variable, and its range was 0.08 to 0.45. The condensation performance of the SAM tube and bare tube increased with decreasing mass fraction of NCG. The SAM tube showed 1.9 to 2.5 times larger dropwise condensation performance than the bare tube. When the mass fraction of NCG decreased in the SAM tube, the rate of increase of the SAM tube was lower because flooded condensation occurred. In addition, filmwise condensation occurred in the SAM tube when more active condensation was generated, and its performance was lower than that of the bare aluminum tube. The flooded and filmwise condensation in the SAM tube is explained by the pinning effect. In conclusion, controlling the condition of the condenser is necessary to improve the condensation performance by surface modification a SAM.

• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.60-68
• /
• 1991

In compacting the melt-spun $Nd_{14}Fe_{76}Co_{4}B_{6}$ and $Nd_{10.5}Fe_{79}Co_{2}Zr_{15}B_{7}$ magnetic powders. the difference in composition induces a different behavior of closed packing rate as a function of aspect ratio of the powders. The $Nd_{10.5}Fe_{79}Co_{2}Zr_{1.5}B_{7}$ alloy having a low Co/Fe ratio (low density) shows the better green density to have an enhanced closed packing rate. An empirical power equation relating the green density with the compacting pressure was obtained such as ${\phi}(g/cm^{2})=5.2~5.6{\times}P^{0.045~0.065}(ton/cm^{2})$. The $Nd_{14}Fe_{76}Co_{4}B_{6}$ alloy having a high Nd/Fe ratio possesses much finer grain size(50~60 nm) than that of $Nd_{10.5}Fe_{79}Co_{2}Zr_{1.5}B_{7}$ alloy and shows the higher coercivity($iH_{c}=14~15kOe$). The higher Nd/Fe ratio in the melt-spun Nd-Fe-Co-B alloy, where the domain wall pinning mechanism was found to be predominant, assists the formation of Nd-rich grain boundary phase acting as a pinning site. The grain boundary ranges over $12~16\;{\AA}$ thick in the Nd-Fe-Co-B alloy while it ranges over $8~12\;{\AA}$ thick in the Nd-Fe-Co-Zr-B alloy.

• Journal of Welding and Joining
• /
• v.25 no.1
• /
• pp.57-62
• /
• 2007

In the coarse grained HAZ of conventional TiN steel, most TiN particles are dissolved and austenite grain growth easily occurrs during high heat input welding. To avoid this difficulty, thermal stability of TiN particles is improved by increasing nitrogen content in EH36-TM steel. Increased thermal stability of TiN particle is helpful for preventing austenite grain growth by the pinning effect. In this study, the mechanical properties and microstructures of high heat input welded Tandem EGW joint in EH36-TM steel with high nitrogen content were investigated. The austenite grain size in simulated HAZ of the steel at $1400^{\circ}C$ was much smaller than that of conventional TiN steel. Even for high heat input welding, the microstructure of coarse grained HAZ consisted of fine ferrite and pearlite and the mechanical properties of the joint were sufficient to meet all the requirements specified in classification rule.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.493-501
• /
• 1998

$YBa_2Cu_3O_X$ samples were fabricated by MPMG(Melt Powdered Melt Growth). Intitial composition of the mixed powders were prepared as follow ; $YBa_2Cu_3O_X$ : $Y_2BaCuO_5$ = 1:0, 1:0.2, 1:0.3, 1:0.4. After the first melt and cooling, 5wt% to 20wt% fo Ag power was added to the powder. Effects of the different initial $Y_2BaCuO_5$ and Ag addition amount on $J_c$ and magnetization of $YBa_2Cu_3O_X$ fabricated by MPMG method were investigated. The critical current density increased with the amount of $Y_2BaCuO_5$ and Ag. It was also observed that the difference between negative and positive magnetization in the magnetization hysteresis measurement at 77K was larger than the case where $Y_2BaCuO_5$and Ag were not added to the $YBa_2Cu_3O_X$ powders. It is concluded that $Y_2BaCuO_5$ sample with 40wt% amount of $Y_2BaCuO_5$ and 20wt% amount of Ag has not only the largest $J_c$ but also the improved pinning effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.191-191
• /
• 2010

초전도 전력 기기를 안정적으로 운용하기 위해서는 고자장하에서 높은 임계 전류 밀도($J_c$)를 지닌 초전도체 개발이 필수적이다. 최근 고자기장에서 전기적 특성을 향상시키는 방법으로는 YBCO 박막선재에 인위적 피닝센터로 고자장하에서도 $J_c$가 크게 증가 되었다고 보고되고 있다. 본 연구에서는 STO(100) 기판 위에 SAM 방법을 이용하여 금 나노분말을 분산시킨 후 PLD로 YBCO 박막을 증착하여 미세구조와 전기적인 특성을 분석하였다. 분산된 금 나노분말은 열처리전 나노입자의 높이는 29~32 nm, 지름은 41~49 nm툴 나타내었고 $800^{\circ}C$에서 진공 열처리 후에는 높이는 25~30 nm, 지름은 52~60 nm로 변형되었다. 임계온도는 순수 YBCO에서 85 K을 나타냈지만 금 나노입자를 적용한 YBCO의 경우는 80K으로 낮아진 것을 확인하였다. 임계전류밀도는 4T에서 측정된 경우 65 K에서는 순수한 YBCO는 141 KA/$cm^2$에서 금 나노입자가 형성된 기판에 증착한 YBCO는 42 KA/$cm^2$로 낮아졌다.

• Journal of Korea Foundry Society
• /
• v.37 no.2
• /
• pp.31-37
• /
• 2017

A new form of austenitic heat-resistant ductile iron was developed and its microstructures and elevated temperature properties were compared to those of Ductile Ni-Resist D5S. According to JMatPro calculations, it was predicted that Mo-rich carbides would be crystallized before the eutectic reaction starts in the developed alloy. At the austenite cell boundaries of the developed alloy, both Mo-rich carbides and Cr-rich carbides were found. In addition, Ni-silicides were found adjacent to Cr-rich carbides in D5S specimen and were identified as $Ni_2Si$. The developed alloy also had greater yield strength and lower tensile strength levels with less elongation due to the dissolution of Mo atoms into the austenite matrix and the precipitation of Mo-rich carbides. From the results of elevated temperature tensile tests and stress-rupture tests, it was found that the developed alloy had elevated temperature properties superior to those of D5S. This was due to the pinning effect of the dissolved Mo atoms in the austenite matrix.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.590-597
• /
• 2016

In this study, six kinds of low-carbon steel specimens with different ferrite-pearlite microstructures were fabricated by varying the Nb content and the transformation temperature. The microstructural factors of ferrite grain size, pearlite fraction, interlamellar spacing, and cementite thickness were quantitatively measured based on optical and scanning electron micrographs; then, Charpy impact tests were conducted in order to investigate the correlation of the microstructural factors with the impact toughness and the ductile-brittle transition temperature (DBTT). The microstructural analysis results showed that the Nb4 specimens had ferrite grain size smaller than that of the Nb0 specimens due to the pinning effect resulting from the formation of carbonitrides. The pearlite interlamellar spacing and the cementite thickness also decreased as the transformation temperature decreased. The Charpy impact test results indicated that the impact-absorbed energy increased and the ductile-brittle transition temperature decreased with addition of Nb content and decreasing transformation temperature, although all specimens showed ductile-brittle transition behaviour.

• Journal of Korea Foundry Society
• /
• v.29 no.5
• /
• pp.213-219
• /
• 2009

Optimum conditions for production of semi-solid Al-Zn-Mg alloy billets was carried out by the Taguchi design method. And, Al-Zn-Mg alloy billets contained Sc (free, 0.1 and 0.3 mass %) were fabricated at optimum conditions. Evolution of microstructure in semi-solid state was investigated through various liquid fractions, holding times and holding temperatures. The Al-Zn-Mg alloy billets reheated at $615^{\circ}C$ during 30min are grain growth and it was fractured due to increasing liquid fraction before quenching. And, during reheating up to $600^{\circ}C$, grain growth of Al-Zn-Mg alloy billets contained Sc (0.1 and 0.3 mass %) was not occurred in comparison with those of Al-Zn-Mg alloy without Sc. It was thought that $Al_3Sc$ phases have a pinning effect in grain boundary and Sc content of 0.1 mass% is able to inhibit grain growth effectively through reheating process.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1361-1363
• /
• 1997

Zinc oxide-based MOV was fabricated with $SiO_2$ additive ranging from 0.5 to 4.0 mol%, and the microstructure and electrical characteristics were investigated. $Zn_2SiO_4$ phase formed by $SiO_2$ additive was distributed at ZnO grains, grain boundaries, and multiple grain junctions. As the content of $SiO_2$ additive increases, average grain size decreased from 40.6 to $26.9{\mu}m$ due to the Pinning effect by $Zn_2SiO_4$ at grain boundaries Breakdown voltage and nonlinear exponent increased, and leakage current decreased in the range of $11.2{\sim}6.14{\mu}A$ with an increasing $SiO_2$. Donor concentration and interface state density decreased, and barrier height increased in the range of $0.71{\sim}1.04eV$ with an increasing $SiO_2$. While, as the content of $SiO_2$ additive, apparent dielectric constant decreased, peak frequency of dissipation factor decreased in the range of $6.45{\times}10^5{\sim}3.00{\times}10^5Hz$, and dissipation peak was $0.31{\sim}0.22$ at Peak frequency.