• 대한조선학회논문집
• /
• 제54권6호
• /
• pp.515-521
• /
• 2017

Large Cavitation Tunnel (LCT) of KRISO enables us to conduct cavitation tests of the propeller attached to a ship model. As the ship model tests are done at rather high Reynolds number of 107~108, flow measurement system such as pitot tube cannot be employed because of structural safety problems in its system and difficulties in installing it within the test section. Thus, KRISO has developed new 3-D LDV system used in large test section of LCT. There are several difficulties in using 3-D LDV, which did not allow efficient operation of it. The first trouble was the calibration using the conventional pin hole. To make the focus with same laser-beam waists at the wanted position, the high spatial resolution CCD is utilized in the calibration procedure for 3-D LDV. The off-axis configuration provides two velocity components in the horizontal plane and on-axis configuration gives third velocity component in the vertical plane. The horizontal velocity components are also obtained in the coincidence mode, which prevents any misleading results in the off-axis configuration. The nominal wake of Aframax tanker model is measured by the developed 3-D LDV system. The measured hull wake showed good agreement with that obtained by CFD calculation.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.439-452
• /
• 1994

One of the chlorofluorocarbon compounds. R-12 deplete atmospheric ozone. It leads to international agreement to reduce CFC production. R-134a has similar thermodynamic properties to CFC-12. It has zero ODP(Ozone Depletion Potential). This Paper focuses on the lubricating oils for using with R-134a PAGs(Polyalkylene Glycol's) and esters are primary lubricants that are now being tested for use with R-134a Because of extreme polarity of R-134a. there are many problems in the selection of lubricating oil. This investigation analyzes compressor working conditions and calculates wear parts friction for simulation testing. Miscibility and material compatibility is proved by sealed glass tests. Friction was tested on the closed type pin on disk wear tester. This equipment simulates actual refrigerating compressor. Environment controlled test made more reliable result than field test Conventional oils(mineral oils, Alkylbenzene, PAO(Polyalpha Olefin) are immiscible with R-134a. PAGs and ester oils are miscible with R-134a. Friction coefficient is similar to conventional system(mineral oil/R-12 systems) at operating condition. At start & stop condition, PAGs/R-134a system has high friction coefficient. It provide reliable result on the lubricity, miscibility, material compatibility of R-134a with these new lubricants. It suggests proper selection of refrigeration oil that may improve compressor durability of performance.

• Archives of Plastic Surgery
• /
• 제35권6호
• /
• pp.675-679
• /
• 2008

Purpose: In the orbital floor fracture, sensory impairment due to the damage of the infraorbital nerve is one of the most common symptom and complication. In this report, we have the assumption that tailoring of $medpor^{(R)}$ for decompression may have correlations to the damage and regeneration of the nerve. Methods: Among patients who had open reduction for pure orbital floor fracture in our hospital from March 2005 to March 2008, we selected 80 cases. In 40 cases, we inserted tailored $medpor^{(R)}$, and in other 40 cases, non-tailored $medpor^{(R)}$ was inserted. Patient's reports were obtained and analyzed, and the pin-prick test and the 2-point discrimination test on the infraorbital nerve regions were done for testing the sensory impairments. Results: The results show that the patients who adopted sculpture of $medpor^{(R)}$ showed higher tendency of recovery of sensory impairments in the patient's subjective report, static touch sensation, static two point discrimination using. And in postoperative 3 months, there are statistically significant recovery of sensory symptoms, signs and the result of sensory tests. Conclusion: From these results, tailored $medpor^{(R)}$ in reconstruction of orbital wall fracture may improve recovery of sensory impairments for decreasing of compression of infraorbital nerve.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제27권3호
• /
• pp.250-257
• /
• 2001

Sensory dysfunction following the injury of the inferior alveolar nerve requires objective examination to get a reproducible data and to provide necessary treatment. This study was designed to evaluate if the SEP(somatosensory evoked potentials) of the mental nerve can be used as an objective method for the diagnosis of nerve injury and sensory disturbances. The subjects were nineteen patients ($37.4{\pm}11.3$ years old) who had been suffered from sensory disturbance of the unilateral lower lip and mental region for over 6 months after the inferior alveolar nerve injuries confirmed by the microsurgical explorations. The clinical neurosensory tests as SLTD(static light touch discrimination), MDD(moving direction discrimination), 2PD(two point discrimination), PPN(pin prick nociception) and accompanied pain were preceded to electro-physiologic examinations as SEP. The score of sensory dysfunction (sum score of all sensory tests) ranged from 0 to 8 were compared to the latency differences of the mental nerve SEPs. The correlation between clinical sensory scores and SEPs were tested by Spearman nonparametric rank correlation analysis, the differences in SEP latency by Kruskal-Wallis test and the latency differences according to PPN and accompanied pain by Mann-Whitney U test. This study resulted that the difference of the latencies between normal side and affected side was $2.22{\pm}2.46$ msec and correlated significantly with the neurosensory dysfunction scores (p=0.0001). Conclusively, the somatosensory evoked potentials of the mental nerve can be a useful diagnostic method to evaluate the inferior alveolar nerve injuries and the change of sensory dysfunction to be reproduced as an objective assessment.

• 농업과학연구
• /
• 제45권2호
• /
• pp.177-184
• /
• 2018

The frost heave process from repeated freezing and thawing actions in winter on forest road cut-slopes is important for forest road maintenance and management. This study investigated the damages of the forest heave process on forest road cut-slopes by measuring the changes in the road-cut surface elevation and sediment production and by conducting vegetation surveys which were aimed at providing information for forest road maintenance plans. The temperature and humidity differences were determined between the north and south cut-slopes. T-test showed that the north slope had a lower temperature and humidity than that of the south slope. Field observations also confirmed frozen soils on the north slopes, indicating that the north slopes are susceptible to frost heave. Sediment was converted to dry weight per unit area ($g/m^2$). T-test showed that the north slope produced more sediment than that of the south slope. The study confirmed that more frost heave occurred on the north cut-slopes than on the south cut-slopes. Vegetation surveys were conducted on five cut-slope plots. Considering the dominant species found above the cut-slopes, vegetations in all the plots are expected to succeed to pine and oak in the future. The dominant species appearing on the cut-slopes of the study area were exotic species because the elapsed time of the site was only 2 - 4 years.

• 한국주조공학회지
• /
• 제20권4호
• /
• pp.230-239
• /
• 2000

High pressure wear characteristics of DCI(Ductile Cast Iron) were investigated through unlubricated pin-on-disc wear test. Wear test were carried out at speed of 23m/min, under pressure of 3MPa and 3.3 MPa. Cu and/or Mn were added to examine the effect of alloying elements on the high pressure wear characteristics of DCI. To investigate the relationship between wear characteristics and mechanical properties of DCI, Brinell hardness and V-notched Charpy impact energy were tested. Wear surface of each specimen was observed by SEM to determine the wear mechanism of DCI under high pressure wear condition. In the mild wear region, wear characteristics of alloyed DCI specimens were very similar to that of unalloyed DCI. But mild-severe wear transition was occurred at different wear distance and wear rate of DCI specimens were changed by alloying elements. In severe wear condition, wear rate of DCI was dramatically increased by the addition of Mn. Although the addition of Cu 0.46wt% did not decrease the wear rate of DCI in the severe wear region, but it delayed the mild-severe wear transition. Under high pressure wear condition, wear rate and mild-severe wear transition were not concerned with hardness of DCI specimens, but they were deeply associated with impact energy changed by alloying elements.

• 한국주조공학회지
• /
• 제20권4호
• /
• pp.240-246
• /
• 2000

Surface layer properties such as composition, phase, hardness, and oxide layer condition are very important if the main failure mechanism of metals is wear. Generally, stable and dense oxide layers are known to decrease the wear rate of metals by prohibition of metallic junction occurred between bare metals. Addition of Si above 4 wt% to DCI(Ductile Cast Iron) is reported to enhance the significant oxidation resistance by forming the silicon-rich surface layer which inhibits further oxidation. And addition of up to 2 wt% Mo to high Si ductile iron produces significant increases in high temperature tensile strength, creep strength, thermal fatigue resistance and oxidation resistance. High pressure wear characteristics of unalloyed DCI(Ductile cast Iron), 4.46 wt% Si ductile iron, 4.3 wt% Si-0.52 wt% Mo ductile iron were investigated through unlubricated pin-on-disc wear test. Wear test was carried out at speed of 23m/min, under pressure of 3 MPa and 3.3 MPa. Wear surfaces of each specimen were observed by SEM to determine the wear mechanism under high pressure wear condition. Addition of Si 4.46 wt% severely deteriorated wear property of ductile iron compared to unalloyed DCI. But combined addition of Si 4.3 wt%andMo0.52wt%decreasedthefrictioncoefficient(${\mu}$)ofductileironsandremarkablydelayedthemild-severeweartransition.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.207-210
• /
• 2017

The suspension arrangement of insulators provides flexibility and assists in power transmission in transmission lines. The performance of the insulator string is strongly influenced by the environmental conditions to which it is exposed, its shape and the inherent material properties of suspension-type insulators. The suspension-type insulators are mostly made from glass, porcelain and ceramic material due to their high resistivity. Irregularity in charge distribution throughout the porcelain insulator may lead to accelerated aging and electrical breakdown. A very high and steep lightning impulse voltage may also cause breakdown of suspension-type insulators. We investigated various material characteristics such as alumina addition, surface morphology, x-ray diffraction pattern and relative density of suspension porcelain insulators manufactured in 1989 (36,000 lbs.), 1995 (36,000 lbs.) and 2001 (36,000 lbs.) by the KRI Company for use in 154 kV high power transmission lines. We compared the material characteristics of these porcelain insulators with that of the top-of-the-line porcelain insulators (36,000 lbs.) manufactured by the NGK Company in 2000. These suspension-type porcelain insulators were exposed to arc and flashover tests to examine their electrical and mechanical strength. It was noted that alumina addition (17 wt.%) for K-2001 was one of the major contributors to the enhancement of the performance of the porcelain insulators and to their ability to withstand very high current generation during the arc test. The porcelain insulators manufactured during 2001 also showed the highest relative density of 95.8% as compared to the other insulators manufactured in 1989 and 1995 respectively 94.2% and 91.5%. We also discuss reports of various failure modes of suspension-type porcelain insulators.

• Tribology and Lubricants
• /
• 제31권2호
• /
• pp.69-77
• /
• 2015

Recently, there have been reports of severe symptoms of wear in bearings due to foreign substances mixed in lubricants. Therefore, studying the effects of foreign substances (such as combustion products and metallic debris) on the wear characteristics of journal bearings and proposing appropriate management standards for lubricant cleanliness have become necessary. Studies on the effect of particle size and concentration of foreign substances on surface damage have actively progressed in the recent times. These studies indicate the possibility of foreign substances causing direct wear of bearing surfaces. However, experiments conducted until now involve only basic tests such as the Pin-on-Disk test instead of those involving real bearing systems. This study experimentally examines the damage to the surface of a journal bearing due to foreign substances (combustion products and alumina) mixed with the lubricant, as well as the effect of the type and size of particles on its wear characteristics. The study uses an experimental journal bearing similar to a real bearing system for conducting the lubrication test. Hydrodynamic Lubrication (HL) numerical analysis, experiment results, and film parameters are used for calculating the operating conditions required for achieving the desired film thickness, and the results of the analysis are modified for considering the surface roughness. The run-time of the experiment is 10 min including the stabilization process. The experiment results show that alumina particles larger than the minimum film thickness cause significant surface damage.

• 한국항행학회논문지
• /
• 제24권4호
• /
• pp.314-321
• /
• 2020

LASAR (logic automated stimulus and response) 소프트웨어는 디지털 전자 회로 카드에 대한 로직 기능시험 및 고장검출을 위한 자동점검프로그램 개발도구이다. LASAR 소프트웨어는 소자의 논리회로 기능 및 입·출력 정의된 정보가 필요하다. 소자 정보가 없으면 정상적인 부품 모델링이 불가능하다. 따라서 본 논문에서는 소자 정보가 없는 PLD (programmable logic device) 소자를 역설계 방법을 통하여 부품 모델링을 수행한다. 개발된 LASAR 프로그램은 고장 시뮬레이션 결과와 단일 고착 고장삽입 방법을 통해 고장 검출율을 확인하였다. 고장 검출율은 기존의 제한적인 모델링은 91%, 역설계를 통한 모델링은 94%로 3% 상승하였다. 또한, EP 310 PLD 소자에 대한 입·출력핀에 대한 22가지 고착결함의 경우 100% 검출하여 양호한 성능을 확인하였다.