• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.83-88
• /
• 2015

In this paper, $2mm{\times}2mm$ sized piezoresistive accelerometers were designed and fabricated. Two kinds of accelerometers with different spring structure are designed. One is an accelerometer with 4 beam spring located in the center of the mass, the other is an accelerometer with 8 beam spring located in the vertices of the mass. The modal analysis of the accelerometers and the structural analysis were performed using ANSYS program. The former has the superior sensitivity characteristics of $21.38{\mu}V/V/g$ and the lower offset drift of $154.45ppm/^{\circ}C$ than the latter.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.274-277
• /
• 1991

A piezoresistive silicon resonator which can be used as an accelerometer is designed and fabricated using silicon micromachining techniques. The device consists of a seismic mass and four deflection beams in which eight piezoresistors are diffused. The structure is fabricated by EPW etching process. The piezoresistors are properly arranged and connected to make a bridge circuit, with which acceleration in only one direction can be measured. According to the experimental results, the first resonant frequency of this resonator is above 15 kHz, and this transducer has a sensitivity of 5.56 ${\mu}V/Vg$.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.19-25
• /
• 1994

When etching rectangular convex corners of silicon using anisotropic etchants such as KOH, deformation of the edges always occurs due to undercutting. Therefore, it is necessary to correct the mass pattern for compensation. Experiments for the compensation method to prevent this phenomenon were carried out. In the result, the compensation pattern of a regular square is suitable for acceleration sensors considering space. With this consequence, silicon piezoresistive acceleration sensor with compensated square pillar type of mass has been fabricated using SDB wafer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.9-15
• /
• 1996

A silicon microaccelerometer is designed and fabricated using silicon epitaxial layers for automotive electronic airbag applications. A cantilever structure is chosen for high sensitivity and piezoresistive detection method is adopted for circuit simplicity and low cost. An optimum design is used to find optimum microstructure sizes for maximum sensitivity subject to performance requirements and design constraints on natural frequency, damping ratio, maximum allowable stress and microfabrication limitations. The microaccelerometer is fabricated by micromachining processing steps, composed of material-selective and orientation-dependent chemical etching techniques. Fabricated prototype shows a sensitivity of 88.6$\mu\textrm{V}$/g within a resonant frequency of 1.75KHz. Estimated performance of the microaccelerometer is compared with measured one. Discrepancy between the theoretical values and the experimental values is discussed together with possible sources of the errors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.350-354
• /
• 2020

In this study, a pressure sensor for each displacement was fabricated based on the silicon-based pressure sensor obtained through simulation results. Wires were bonded to the pressure sensor, and a piezoresistive pressure sensor was inserted into the printed circuit board (PCB) base by directly connecting a micro-electro-mechanical system (MEMS) sensor and a readout integrated circuit (ROIC) for signal processing. In addition, to prevent exposure, a non-conductive liquid silicone was injected into the sensor and the entire ROIC using a pipette. The packaging proceeded to block from the outside. Performing such packaging, comparing simple contact with strong contact, and confirming that the measured pulse wavelength appears accurately.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.102-113
• /
• 1995

일반적으로 단결정 실리콘은 거의 모든 전자소자의 재료로서 널리 사용되고 있으며 제조공정기술 또한 상당한 수준에 도달하고 있다. 최근에는 실리콘 자체의 우수한 압저항효과, 기계적 특성 그리고 반도체 제조공정을 이용한 미세가공기술인 마이크로머시닝을 이용하는 반도체 압력센서에 대한 연구가 활발히 진행되고 있다. 기계식 압력센서에 비해서 전기적 변화를 이용하는 반도체 압력센서에서는 소형, 저가격, 고신뢰성, 고감도, 다기능, 고분해, 고성능 및 집적화 등의 우수한 특성을 지니고 있다. 본고에서는 이러한 특성을 가지는 반도체 압력센서중 특히, 압저항형과 용량형 압력센서의 구조와 원리, 그리고 연구.개발동향 및 향후 전망에 관해서 기술하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.274-274
• /
• 2008

This paper describes on the fabrication and characteristics of a 3C-SiC (Silicon Carbide) micro pressure sensor for harsh environment applications. The implemented micro pressure sensor used 3C-SiC thin-films heteroepitaxially grown on SOI (Si-on-insulator) structures. This sensor takes advantages of the good mechanical properties of Si as diaphragms fabricated by D-RIE technology and temperature properties of 3C-SiC piezoresistors. The fabricated pressure sensors were tasted at temperature up to $250^{\circ}C$ and indicated a sensitivity of 0.46 mV/V*bar at room temperature and 0.28 mV/V*bar at $250^{\circ}C$. The fabricated 3C-SiC/SOI pressure sensor presents a high-sensitivity and excellent temperature stability.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.192-194
• /
• 1993

In this paper, a silicon piezoresistive accelerometer of which the cantilevers have uniform thickness is designed and fabricated with SOI wafer. The accelerometer consists of a seismic mass and four cantilevers, and is fabricated mainly by the anisotropic etching method using EPW etchant. The fabrication processes are that of the frontside processes including the etching of the cantilevers and the doubleside alignment holes, the diffusion of the piezoresisters and patterning of the contact windows, and the metal connection process, and that of the backside processes including the etching of the shallow cavity and the seismic mass. Because of the uniformity of thickness, the performance of the accelerometer fabricated with SOI wafer is expected to be better than that of accelerometer fabricated by the time-controlled etching method.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1994-1996
• /
• 1996

This paper presents the fabrication and testing of a polysilicon piezoresistive accelerometer with p+ silicon diaphragm by simple process such as two step photolithography for the RIE process to form the cantilevers and a deep anisotropic etch process for the complete fabrication of the accelerometer. The fabricated accelerometer consists of a seismic mass and four cantilevers on which polysilicon piezoresistors are formed. The measurement of the output signal from the bridge circuit of the fabricated accelerometer is carried out with the HP 3582A spectrum analyzer. The analysis of the experimental result is showed in terms of the sensitivity and the resonant frequency. At atmospheric condition, the measurement values of the sensitivity and the resonant frequency are $11\;{\mu}V/Vg$ and 475 Hz, respectively.

• Journal of Sensor Science and Technology
• /
• v.13 no.3
• /
• pp.175-181
• /
• 2004

A pressure sensor for high temperature was fabricated by using a SDB(Silicon-Direct-Bonding) wafer with a Si/$SiO_{2}$/ Si structure. High pressure sensitivity was shown from the sensor using a single crystal silicon of the first layer as a piezoresistive layer. It also was made feasible to use under the high temperature as of over $120^{\circ}C$, which is generally known as the critical temperature for the general silicon sensor, by isolating the piezoresistive layer dielectrically and thermally from the silicon substrate with a silicon dioxide layer of the second layer. The pressure sensor fabricated in this research showed very high sensitivity as of $183.6{\mu}V/V{\cdot}kPa$, and its characteristics also showed an excellent linearity with low hysteresis. This sensor was usable up to the high temperature range of $300^{\circ}C$.