• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.131-145
• /
• 2015

The voltage-source inverters (VSI) supplying a motor drive are prone to open transistor faults. To address this issue in fault-tolerant drives applicable to electric vehicles, a new open transistor fault diagnosis (FD) method is presented in this paper. According to the proposed method, in order to define the FD index, the phase angle of the converter output current is estimated by a simple trigonometric function. The proposed FD method is adaptable, simple, capable of detecting multiple open switch faults and robust to load operational variations. Keeping the FD in mind as a mandatory part of the fault tolerant control algorithm, the FD block is applied to a five-phase converter supplying a multiphase fault-tolerant PM motor drive with non-sinusoidal unbalanced current waveforms. To investigate the performance of the FD technique, the fault-tolerant sliding mode control (SMC) of a five-phase brushless direct current (BLDC) motor is developed in this paper with the embedded FD block. Once the theory is explained, experimental waveforms are obtained from a five-phase BLDC motor to show the effectiveness of the proposed FD method. The FD algorithm is implemented on a field programmable gate array (FPGA).

• 한국전자파학회논문지
• /
• 제27권6호
• /
• pp.504-511
• /
• 2016

본 논문에서는 디지털 수신 능력을 갖는 능동 위상 배열 안테나의 근접전계 수신시험 중, 수신 채널에 이득 및 위상 변화가 발생하더라도 보정 경로 및 수신 채널을 통과한 신호를 이용하여 수신 채널에 발생한 이득 및 위상 변화량을 추출하고, 이를 근접전계 데이터에 직접 보상하여 수신채널에 변화가 발생하지 않은 경우에 수행한 근접전계 시험과 동등한 결과를 획득할 수 있는 방법을 제안하였다. 제안한 방법은 근접전계 수신시험을 위한 타이밍의 일정 구간에 보정 경로를 통하여 수신 채널의 상태를 감시하는 시간 구간을 추가하고 이를 보정하는 방식이다. 제안한 방법의 검증을 위하여 디지털 수신 능력을 갖는 X-대역의 능동 위상 배열 안테나와 평면형 근접전계 시험 시설을 이용하여 측정하였다. 수신 채널에 변화가 보정된 보상 패턴과 수신 채널에 변화가 없었던 기준 패턴과 비교할 때, 제안한 방법이 유효함을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.104-106
• /
• 1996

In this paper, the dynamic motion driven by electromagnetic force of transformer windings is modeled and its characteristics are numerically analyzed. The electromagnetic field is obtained using the 2D finite element method taking account of anisotropic property of iron core, and the electromagnetic force on the transformer winding is calculated from Lorenz's force formula using the field distribution result. The system motion equation driven by electromagnetic force and gravitational force is numerically analyzed using the 4-order Runge-Kutta algorithm. Above analyses procedure is applied to a single-phase core-type transformer to validate its algorithm.

• Transactions on Electrical and Electronic Materials
• /
• 제15권4호
• /
• pp.182-188
• /
• 2014

When the windowed DFT algorithm is applied in harmonic measurements, the problem of initial-phase sensitivity will be encountered, this has an effect on harmonic amplitude accuracy. In this paper, the origin of initial-phase sensitivity is analyzed and the main factors that influence the level of initial-phase sensitivity are demonstrated. A method of reducing initial-phase sensitivity is proposed to increase the stability of harmonic measurements. We found that initial-phase sensitivity is determined by the side lobe peak level of the window functions when synchronous deviation is fixed. In addition, increasing the length of the time recorded can be used to remove initial-phase sensitivity. The correctness and validity of our conclusions have been confirmed through numerical results and field tests.

• 한국해안·해양공학회논문집
• /
• 제24권4호
• /
• pp.277-286
• /
• 2012

기체와 액체의 유동 및 고체의 변형을 동시에 고려할 수 있는 혼상류모델을 이용하여 파동장을 해석하는 경우, 서로 다른 비혼합의 유체 경계면의 시간변형을 고정도로 추적하는 것이 대단히 중요하다. 본 연구에서는 경계면의 추적에 있어서 VOF(Volume of Fluid)법으로 대표되는 경계면 형상의 재구축이 필요한 Geometrical-type의 경계추적법의 대신에 Algebraic-type의 경계추적법인 THINC(Tangent of Hyperbola for INterface-Capturing)법을 적용하였다. THINC법은 경계면에 대한 형상의 구축이 필요하지 않으므로 VOF법에 비해 비교적 간단한 알고리즘을 가지며, 기존의 Navier-Stokes solver에로 적용성이 용이한 장점을 갖는다. 본 연구에서는 THINC법의 기본적인 이류특성을 고찰하고, 혼상류수치모델인 TWOPM(one-field Model for immiscible TWO-Phase flows)과 결합한 수치모델을 파동장에 적용하여 비혼합 혼상류에서 경계면의 추적능을 검토하였다. 그 결과, 혼상류의 경계면 추적에 있어서 상대적으로 간단한 알고리즘의 THINC법이 기존의 VOF법과 유사한 정도를 갖는 해석법이라는 것을 확인할 수 있었고, 따라서 향후 기포의 연행을 동반하는 쇄파 및 쇄파력의 해석 등에 그의 적용성이 기대된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1091-1093
• /
• 2001

The power semiconductor is widely used in the power plant or industrial field because of genealization and enlargement. It has been controlled and operated according to its own control method. Especially in case of Power plant, it plays a major role in AVR(Automatic Voltage Regulator) or electro chlorination control circuits. Generally, they used in Analog control system at above field. But each SCR current value is different because of load unbalance or switching characteristic variations, it may cause power plant unit trip or system disorder according to SCR element burn out or bad operating condition. Therefore, in this paper a development of 3 phase current balance control algorithm is described. it gets over the past analog control system limit, controls SCR gate firing angle for 3 phase current balance.

• Progress in Superconductivity
• /
• 제1권1호
• /
• pp.56-60
• /
• 1999

Ultra fine MgO particles added BSCCO tapes were fabricated by tape casting using Doctor Blade Method and enclosed by silver foil for different starting compositions (that is, 2223 major, 2212 major). In order to obtain optimum microstructure, thermomechanical treatment was done. Microstructure and phase were analyzed by XRD, SEM and DTA. The critical current density was measured under magnetic field at 77K. The tapes fabricated from the precursor powder with BSCCO-2223 phase (>90%) result in a microstructure with a larger grain size and higher transport critical current density value under magnetic field at given thermomechanical treatment conditions.

• 전기의세계
• /
• 제19권3호
• /
• pp.1-9
• /
• 1970

In this paper, the equation for the generated force is introduced, on the basis of Maxwell's electromagnetic equation, by dividing the air-gap magnetic field into the region of the constant amplitude and the region of the pulsating field in the both ends of iron core, in the case that the typical 3 phase winding is employed in the double sided 3 phase linear induction motor with sheet rotor in accrodance with the winding method of rotary induction machine. With the effect of the overhang region being taken into account, the result, in which the equation is established, inducates that theoretical values nearly coincides with the measured values in the interval of slip s=0-0.8.

• Journal of Magnetics
• /
• 제16권2호
• /
• pp.88-91
• /
• 2011

Steam generator tubes (SGTs) in nuclear power plants (NPPs) are a boundary between the primary side generating heat by nuclear fission and the secondary side generating electric power by a turbine. The water inside the SGT is high temperature and high pressure. Therefore, defects and magnetic phases (MPs) are partly produced in non-magnetic SGT by high stresses and temperatures. This causes trouble regarding the safety of SGTs but it is difficult to detect the MP using the conventional eddy current technique (ECT). In particular, a circumferential defect (CD) and circumferential magnetic phase (CMP) cannot detected by ECT. Consequently, a new method is needed to detect CDs and CMPs in SGT. A new U-type yoke with two types of coils was designed and the reactance signal by the CMPs and CDs in the SGT material was simulated.

• 한국실내디자인학회논문집
• /
• 제9호
• /
• pp.10-17
• /
• 1996

With the ever-increasing important of high-speed information in society as we move towards the 21 st century. Interior design and it's working condition has been changed a great deal included a sort of each special character and make a difference against the others. It used to be find a great poles asunder of worker's safety and project quality according to the environmental dimension of interior construction field as if they should be a pleasantness or poor condition. This research aimed to improvement of environmental construction field of interior with construction engineers and particular interior labors in 4 phases as : ⅠThe preparatory phase : -Secure a Budget, Environmental safety supervisor -Fix of Design quality, Construction period. -Choice of Construction method, Sub constructing Ⅱ. Starting work phase ; -Capacity , Safety of temporary power line. -Carriage, Stock of Material -Safety of Electronic tools, -Personal protector. Ⅲ. Working period ; -Ventilation, I illumination of working place. -Measurement of environmental working condition Ⅳ.Finish working phase ; -Analysis of measurement data. -Evaluation and making up for the weak point. -Keeping data.