• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.19 no.1
• /
• pp.76-87
• /
• 2014

Chlorophyll a in seawater which is an indicator of phytoplankton biomass and primary production is determined by High Performance Liquid Chromatography (HPLC), Fluorometry and Spectrophotometry. In this study, various methods for chlorophyll a determination in seawater are compared using in situ seawater samples from Korean seas. Three inter-laboratory comparison campaigns were carried out using chlorophyll a standard samples (R0) and in situ seawater samples, collected from the East China Sea (R1) and the East Sea (R2). 6 laboratories by HPLC methods, 4 laboratories by fluorometry, and 3 laboratories by spectrophotometry participated. Precisions, defined as the coefficient of variation (CV) were within 9% in standard samples, 0.8~20% (average: 6.1%) in R1, 4~21% (average: 13.2%) in R2. Discrepancy in three methods was approximately 20% within the range of the sample homogeneity intended the laboratory precision (R1: 8%, R2: 15%). The discrepancy in laboratories was greater than the discrepancy in methods. The chlorophyll a concentrations can be produced within 20% discrepancy in spite of using different methods. It is recommended to consider this 20% discrepancy when using the chlorophyll a data produced by different laboratories and different methods.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.1-8
• /
• 2014

Structures requiring chemical resistance are usually coated with surface protecting agents, but the cost for maintenance and re-construction is incurred due to the low durability. Therefore, in this study, sulfur was polymerized and the performance was examined so that it could be used as the concrete surface protecting agents for structures requiring chemical resistance. The evaluation results indicated that for the spray of the sulfur polymer surface coating agents, the application of the gravity type was appropriate; and for the number of coating times, about 3 cycle spray gave the best results. For the surface condition of the concrete to be coated with the surface protecting agents, outstanding quality was obtained above room temperature ($20{\sim}30^{\circ}C$), and the bond strength increased as the temperature increased. The evaluation results of the strength characteristics depending on the filler content of the surface protecting agents indicated that about 20~40% filler mixing contributed to the strength improvement as it reduced the shrinkage of the sulfur polymer. Also, the mixing of silica showed larger increase in the bond strength than the mixing of fly ash, and the most outstanding bond strength characteristics could be obtained by the mixing of both silica and fly ash. In the case of the chemical resistance, the strength reduction was minimized and outstanding chemical resistance was obtained when the fly ash and silica were substituted by 20%, respectively. The performance evaluation of the chloride ion penetration indicated that for the specimens coated with the sulfur polymer surface protecting agents, the chloride ion penetration resistance increased by 29~48% compared to the specimen without the coating of the surface protecting agent. The examination of the coating condition of the surface protecting agents, compressive strength, bond strength, chemical resistance, and salt damage resistance indicated that in the range of this study, the optimal level was when the silica and fly ash were substituted by 20%, respectively, as the filler for the sulfur polymer.

• Journal of Life Science
• /
• v.21 no.11
• /
• pp.1541-1548
• /
• 2011

This study was carried out to evaluate the effects of the addition of different levels of CFP (Cordyceps with fly pupa) on growth performance in broiler chickens. 400 broiler chicks (Ross 308, 1 day old) were sorted randomly into 4 treatment groups and fed experimental diets for 35 days. The treatment groups were divided into a control group not fed with CFP (T1), and treatment groups fed with CFP 2.0% (T2), CFP 3.5% (T3), and CFP 5.0% (T4). Although the broilers' weight gain and feed efficiency were significantly higher (p<0.05) in the T3 group throughout the entirety of the test period, no statistically significant differences were noted among the T1 and T2, T4 groups. Triglyceride in the blood, total cholesterol, and LDL-C were significantly lower in the CFP treatment groups than in the control group (p<0.05). The blood lipid reduction rate ranged from 5.32 to 10.63% for triglycerides, from 9.23 to 12.62% for total cholesterol, and from 44.67 to 53.81% for LDL-C in the CFP treatment groups relative to the control group. The abdominal fat weight ratio was reduced significantly in the CFP treatment groups (p<0.05) compared with the control group, with a reduction rate range of 17.67-21.68%. Broiler carcass weight, carcass rate, and ratios of breast muscle, skin and thigh muscle weights to carcass weight were significantly higher in the T3 group, and statistically significant differences were noted among the T1 and T2, T4 groups (p<0.05). Enteropathogenic E.coli and Salmonella were lower in the CFP treatment groups than in the control group, whereas the beneficial bacteria Bifidobacteria were significantly higher in the CFP treatment groups than in the control group (p<0.05). These findings suggest that the Cordyceps with fly pupa can improve the carcass characteristics and body weight gain in broiler chickens.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.203-212
• /
• 2005

Cellulose insulation is primarily manufactured from recycled newsprint and treated with fire retardants for the fire resistance. Thanks to the fire retardants, it is not combustible and flammable. In addition to that, Its thermal resistance is much better than that of fiberglass or rock wool. It is made from waste paper and easily decayed when it is demolished, and it has small embodied energy. So it is very environment-friendly building material. For broader use of cellulose insulation in buildings in Korea, it is necessary to test its physical performance to compare the results with the requirements on the Korean Building Code. To this end, apparent thermal conductivity (ka) measurements of Korean-made loose-fill cellulose insulations were recently completed using equipment that was built and operated in accordance with ASTM C 518 and the fire resistance was tested in accordance with ASTM C 1485. Korean loose-fill cellulose has thermal conductivity about 5% greater than the corresponding U.S. product at the same density. This is likely due to differences in the recycled material being used. Both spray-applied and loose-fill cellulose insulation lose about 1.5% of their thermal resistivity for $5.5^{\circ}C$ increase in temperature. The fire resistance of cellulose insulation is increased in linear proportion to the increase of the rate of fire retardant. Thanks to the high fire resistance, cellulose insulation can be used as a substitution of Styrofoam or Urethane foam which is combustible. The thermal conductivity of cellulose insulation was $0.037-0.043W/m{\cdot}K$ at the mean specimen temperature from $4-43^{\circ}C$. It corresponds to the thermal resistance of "Na Grade" according to the Korean Building Code. The effect of chemical content on thermal conductivity was negligible for all but the chemical-free specimen which had the highest value for the thermal conductivity over the temperature range tested. The thermal resistance of cellulose insulation is better than that of fiberglass or rock wool, and its fire resistance is higher than that of Styrofoam or Urethane foam. Therefore it can be substituted for those above considering its physical performance. Cellulose insulation is no more expensive than Styrofoam or rock wool, so it is recommended to use it more widely in Korea.

• Journal of The Korean Association For Science Education
• /
• v.36 no.4
• /
• pp.563-579
• /
• 2016

This study seeks educational implication by analyzing research papers dealing with science assessment in the most recent 30 years in Korea. The main purpose of the study is to analyze the trends in published papers on science assessment, their purpose, methodology, and key words, especially concentrating on the cognitive and affective domains. We selected 273 research articles and categorized them by research object, subject, methodology, and contents. To examine the factors that affect the research trend, we also tried to contextualize papers' theme in terms of changes in national curriculum and assessment system during the contemporary period. As a result, an overall research trend reflects changes in science curriculum and assessment events such as implementation of college scholastic ability test or performance assessment. There is an unequal distribution in various aspects of the researches, showing a superiority in cognitive domains than the affective ones. By using standardized data obtained through the national and international assessment of educational achievement in science, quantitative researches were superior to qualitative ones. Studies on cognitive domain use variously written- and performance-based tests, whereas most studies of the affective ones prefer written tests. Applied research and evaluation research are predominant comparing to basic ones, which most of the research methodology is based on statistics. Lastly, we found out that key words and subjects tend to be subdivided and detailed rather than general and comprehensive, as time goes on. Such trend will be helpful to elaborate and refine assessment tools that have been regarded as a problem.

• Progress in Medical Physics
• /
• v.12 no.2
• /
• pp.103-112
• /
• 2001

Purpose: The purpose of this study was to investigate the current status of performing nuclear medicine quality control in korea and to test selected protocols of quality control of nuclear medicine counting system and gamma camera. Materials and Methods: Fifty three hospitals were included to investigate the current status of nuclear medicine quality control in korea. The precision of dose calibrator and thyroid uptake system was measured with Tc-99m 35.52 MBq for 2 minuets and Tc-99m 5.14 MBq for 10 sec every one minute, respectively. The sensitivity of CeraSPECT$^{TM}$ with low energy high resolution parallel hole collimator was measured using two cylindrical phantoms with 15 cm in diameter and 12 cm and 30 cm in heights containing Tc-99m. The correction factor for sensitivity of CeraSPECT$^{TM}$ was calculated using phantom data. The system planar sensitivity, uniformity, count rate and spatial resolution were measured for Varicam gamma camera with low energy high resolution parallel hole collimator using 140 keV centered 20% energy window, 256$\times$256 or 512$\times$512 matrix sizes. Results: The quality control of dose calibrator and well counter were showed poor performance status. On the other hand, The quality control of gamma camera and other systems were showed relatively good performance status. The results of precision of dose calibrator and thyroid uptake system was $\pm$1.4%(<$\pm$5%) and chi^2=29.7(>16.92), respectively. It showed that the sensitivity of CeraSPECT$^{TM}$ was higher in center slices compared with the edge slices. After correction of nonuniform sensitivities for patient data, it showed better results compare with prior to correction. System planar sensitivity of Varicam gamma camera was 4.39 CPM/MBq. The observed count rate at 20% loss was 102,407 counts/sec (head 1), 113,427 counts/sec (head 2), when input count rate was 81,926 counts/sec (head 1), 90,741 counts/sec (head 2). The spatial resolution without scatter medium were 8.16 mm of FWHM and 14.85 mm of FWTM. The spatial resolution with scatter medium were 8.87 mm of FWHM and 18.87 mm of FWTM. Conclusion: It is necessary to understand the importance of quality control and to perform quality control of nuclear medicine devices.vices.

• Clean Technology
• /
• v.24 no.3
• /
• pp.198-205
• /
• 2018

This study investigated the influence of catalyst preparation on the activity of $Co-CeO_2$ catalyst for $N_2O$ decomposition. $Co-CeO_2$ catalysts were synthesized by co-precipitation and incipient wetness impregnation. In order to estimate the performance of the as prepared catalysts, direct catalytic $N_2O$ decomposition test was carried out under $250{\sim}375^{\circ}C$. As a result, the catalyst prepared by co-precipitation (CoCe-CP) showed an enhanced performance on $N_2O$ decomposition reaction even in the presence of $O_2$ and/or $H_2O$, whereas the impregnation catalyst (CoCe-IM) did not. In order to investigate the difference in catalytic activity, characterization such as XRD, BET, TEM, $H_2-TPR$, $O_2-TPD$, and XPS was conducted. It is confirmed that the particle size and specific surface area were changed depending on the catalyst preparation method and the synthesis process influenced the physical properties of the catalysts. In addition, the improvement in the activity of the catalyst prepared by co-precipitation is due to the enhanced reduction from $Co^{3+}$ to $Co^{2+}$ and the improved oxygen desorption rate. However, it has been confirmed that the surface electron state and binding energy, which are related to $N_2O$ decomposition, do not change depending on the preparation method.

• Korean Journal of Poultry Science
• /
• v.34 no.4
• /
• pp.279-286
• /
• 2007

This study was conducted to induce molting with DDGS and non-salt diet and compare the effect of feeding molting and fasting molting on the performance, egg quality, and visceral organs in laying hens for animal welfare. One-hundredeight 62-wk-old White Leghorn hens that egg production was over 80% and average weight was $1.8{\pm}0.1kg$ were used in this study. Treatments were control(non-molt treatment), feeding molt treatment(DDGS, non-salt diet), and fasting molt treatment. The four treatments were administered to three replicate group of nine hens wherein each group. All treatment groups were fed the basal diet(CP 15%, ME 2,700 kal/kg) for two weeks as the adaptation period. Test Periods were 28 days at all treatments. Egg production decreased for 18 days to be 0% at feeding molting treatment, and for 17 days to be 0% at non-salt feeding molting treatment. Egg production stopped for 6 days at fasting molting treatment. Egg production restarted after 12 days molt at feeding molting treatment, while after 16 days at fasting molting treatment. On the egg quality was improved at molting treatments (p<0.05) except egg yolk. Egg shell tissue was crowded at molting treatment to compare to control. Liver weights, heart weight, and oviduct weight of laying hens decreased at molting treatments(p<0.05). Finally, feeding molting might could be replaced fasting molting on the welfare and further studies were needed about molting program.

• Journal of Intelligence and Information Systems
• /
• v.16 no.4
• /
• pp.67-84
• /
• 2010

In terms of business, forecasting is a work of what is expected to happen in the future to make managerial decisions and plans. Therefore, the accurate forecasting is very important for major managerial decision making and is the basis for making various strategies of business. But it is very difficult to make an unbiased and consistent estimate because of uncertainty and complexity in the future business environment. That is why we should use scientific forecasting model to support business decision making, and make an effort to minimize the model's forecasting error which is difference between observation and estimator. Nevertheless, minimizing the error is not an easy task. Case-based reasoning is a problem solving method that utilizes the past similar case to solve the current problem. To build the successful case-based reasoning models, retrieving the case not only the most similar case but also the most relevant case is very important. To retrieve the similar and relevant case from past cases, the measurement of similarities between cases is an important key factor. Especially, if the cases contain symbolic data, it is more difficult to measure the distances. The purpose of this study is to improve the forecasting accuracy of case-based reasoning approach using fuzzy relation and composition. Especially, two methods are adopted to measure the similarity between cases containing symbolic data. One is to deduct the similarity matrix following binary logic(the judgment of sameness between two symbolic data), the other is to deduct the similarity matrix following fuzzy relation and composition. This study is conducted in the following order; data gathering and preprocessing, model building and analysis, validation analysis, conclusion. First, in the progress of data gathering and preprocessing we collect data set including categorical dependent variables. Also, the data set gathered is cross-section data and independent variables of the data set include several qualitative variables expressed symbolic data. The research data consists of many financial ratios and the corresponding bond ratings of Korean companies. The ratings we employ in this study cover all bonds rated by one of the bond rating agencies in Korea. Our total sample includes 1,816 companies whose commercial papers have been rated in the period 1997~2000. Credit grades are defined as outputs and classified into 5 rating categories(A1, A2, A3, B, C) according to credit levels. Second, in the progress of model building and analysis we deduct the similarity matrix following binary logic and fuzzy composition to measure the similarity between cases containing symbolic data. In this process, the used types of fuzzy composition are max-min, max-product, max-average. And then, the analysis is carried out by case-based reasoning approach with the deducted similarity matrix. Third, in the progress of validation analysis we verify the validation of model through McNemar test based on hit ratio. Finally, we draw a conclusion from the study. As a result, the similarity measuring method using fuzzy relation and composition shows good forecasting performance compared to the similarity measuring method using binary logic for similarity measurement between two symbolic data. But the results of the analysis are not statistically significant in forecasting performance among the types of fuzzy composition. The contributions of this study are as follows. We propose another methodology that fuzzy relation and fuzzy composition could be applied for the similarity measurement between two symbolic data. That is the most important factor to build case-based reasoning model.

• Journal of Aquaculture
• /
• v.21 no.1
• /
• pp.26-33
• /
• 2008

This study investigated the synergistic effects of dietary supplementation of quartz porphyry(QP) and a laboratory developed feed stimulants, BAISM(BS) on growth performance and utilization as the additives for juvenile eel Anguilla japonica. Six isoenergetic experimental diets(18.2 kJ/g) were formulated to contain 50% crude protein, 15% lipid with or without dietary QP(Song-Gang stone, Davistone, Korea) and BS supplementation. QP and BS were provided at 0% in the control diet($Q_0B_0$) and at 0.7% QP+0% BS($Q_{0.7}B_0$), 0.7% QP+0.3% BS($Q_{0.7}B_{0.3}$), 0.7% QP+0.5% BS($Q_{0.7}B_{0.5}$), 0.7% QP+0.75% BS($Q_{0.7}B_{0.75}$) and 0.7% QP+1.0% BS($Q_{0.7}B_{1.0}$) in experimental diets on dry matter basis. After four weeks of adaptation, triplicate groups of 30 fish initially averaging $15{\pm}0.1g(mean{\pm}SD)$ were randomly distributed into each aquarium, and they were fed one of the experimental diets for 8 weeks. By the end of the feeding trial, weight gain(%), specific growth rate(%), feed efficiency(%) and protein efficiency ratio of fish fed diet $Q_{0.7}B_{0.5},\;Q_{0.7}B_{0.75}\;and\;Q_{0.7}B_{1.0}$, were significantly higher(P<0.05) than those of fish fed the other diets. But, $Q_{0.7}B_{0.5},\;Q_{0.7}B_{0.75}\;and\;Q_{0.7}B_{1.0}$ were no significant differences(P<0.05). In challenge test, fish were infected by intraperitoneal injection of 0.1 mL bacterial suspension with Edwardsiella tarda per fish after the feeding trial. As a result, fish fed QP and BS supplemented diets have a significantly higher cumulative survival rate than those of fish fed control diet(P<0.05). In conclusion, these results indicated that the optimum dietary supplementation level of QP and BS could be approximately 0.7% quartz porphyry+0.5% BAISM($Q_{0.7}B_{0.5}$) of diet based on WG, FER, SGR, PER, cumulative survival rate in juvenile eel A. japonica.