본 연구는 도로 운영시 강우로 인하여 발생하는 배수 취약구간에 대하여 현장 조사를 통하여 도로 배수 취약구간의 발생 원인을 과학적이고 구체적으로 규명하는데 목적이 있다. 도로 배수 취약구간의 발생 원인을 규명하기 위하여 배수취약구간에 대한 기존 연구결과 및 현황 자료를 검토하였으며, 도로 노면 배수시설과 도로 인접지 배수시설에 대한 취약구간을 조사 및 분석한 결과, 시공 및 기타의 원인으로 발생한 배수 취약구간이 45.7%, 도로의 기하구조가 원인이 된 배수 취약구간은 32.3%, 도로의 수리 수문의 원인은 22.0%로 분석되었으며, 분석된 원인 별 개선 방안으로서 i)시공 및 기타 부분에서는 토사측구의 재료 변경, 단면의 크기 상향 및 수리학적 근거를 바탕으로 한 용량의 산정을, ii)도로의 기하구조 측면에서는 편경사 및 종단선형을 고려한 합성경사의 도출 및 범위 산정과 종단 오목부 구간의 배수구조물 적정 간격의 제시를, iii)도로의 수리 수문 측면에서는 1분단위 강우강도식의 사용과 노면 강우의 부등류 흐름 해석 기법의 적용과 선형 배수방식에 따른 도로 노면 강우의 신속배제를 개선 방안으로 제안하였다.
PURPOSES : The piezoelectric energy road analysis technology using a three-dimensional finite element method was developed to investigate pavement behaviors when piezoelectric energy harvesters and a new polyurethane surface layer were installed in field conditions. The main purpose of this study is to predict the long-term performance of the piezoelectric energy road through the proposed analytical steps. METHODS : To predict the stresses and strains of the piezoelectric energy road, the developed energy harvesters were embedded into the polyurethane surface layer (50 mm from the top surface). The typical type of triaxial dump truck loading was applied to the top of each energy harvester. In this paper, a general purpose finite element analysis program called ABAQUS was used and it was assumed that a harvester is installed in the cross section of a typical asphalt pavement structure. RESULTS : The maximum tensile stress of the polyurethane surface layer in the initial fatigue model occurred up to 0.035 MPa in the transverse direction when the truck tire load was loaded on the top of each harvester. The maximum tensile stresses were 0.025 MPa in the intermediate fatigue model and 0.013 MPa in the final fatigue model, which were 72% and 37% lower than that of the initial stage model, respectively. CONCLUSIONS : The main critical damage locations can be estimated between the base layer and the surface layer. If the crack propagates, bottom-up cracking from the base layer is the main cracking pattern where the tensile stress is higher than in other locations. It is also considered that the possibility of cracking in the top-down direction at the edge of energy harvester is more likely to occur because the material strength of the energy harvester is much higher and plays a role in the supporting points. In terms of long-term performance, all tensile stresses in the energy harvester and polyurethane layer are less than 1% of the maximum tensile strength and the possibility of fatigue damage was very low. Since the harvester is embedded in the surface layer of the polyurethane, which has higher tensile strength and toughness, it can assure a good, long-term performance.
임도 옆도랑침식에 영향을 미치는 요인의 평가 및 안정도 판별을 위하여 광릉시험림의 임도를 대상으로 조사를 실시한 결과 침식에 미치는 기여순위는 종단물매, 시설위치, 절토사면경사, 절토사면구성물질, 유하거리, 노면형태, 노면재료, 절토사면피복도, 절토사면길이 순으로 나타났다. 임도 옆도랑침식을 유발하는 요인을 평가하면, 종단물매는 8% 이상, 임도시설위치는 산록(山麓)과 중복(中腹), 절토사면경사는 $50^{\circ}$ 이상, 절토사면토성은 견질토사, 자갈섞인 토사, 호박돌섞인 토사, 유하거리는 80m 이상의 지역에서, 그리고 노면재료는 토사도(土砂道)와 자갈부설도에서, 노면형태의 경우에는 철(凸)형과 직선형, 절토사면 피복도(被覆度)는 피복도가 중(中)이상인 곳에서 임도 옆도랑침식이 발생할 가능성이 높은 것으로 예측(豫測)되었다.
Isotocin (IT)은 포유류의 oxytocin과 유사한 호르몬으로 어류의 행동 조절과 스트레스에 대한 반응, 그리고 삼투압 조절에 이르기까지 다양한 생리반응에 관여한다고 추정된다. 해수 관상어인 cinnamon clownfish의 IT 유전자 구조와 기능을 연구하기 위하여 genomic DNA와 뇌의 cDNA 주형으로부터 유전자를 확보하였다. 세 개의 exon과 156개의 아미노산을 표지하는 ORF로 이루어진 IT 전구물질 유전자는 19개 아미노산으로 이루어진 신호 부위, 9개 아미노산 호르몬 부위, 3개 아미노산의 효소 조절 부위, 그리고 125개 아미노산의 neurophysin 호르몬 부위로 구성되었다. 조직별 RT-PCR 분석결과는 IT 전구물질 유전자가 뇌와 생식소에서 발현됨을 보여준다. 해수 (34 ppt) 적응 개체의 아가미에서는 염류세포 바깥 표면에 apical crypt가 보이는데 비하여, 15 ppt로 낮춘 저염분 적응 개체의 아가미는 표면이 pavement cell로 덮여있는 평평한 구조를 보여준다. 아가미 세포의 Na+/K+-ATPase 활성은 저염분 순응 초기에 증가하다 시간이 지날수록 정상 수준을 회복하는 양상을 보여주는데, 이는 prolactin과 같이 저염분 초기순응 및 항상성 유지에 관여함을 의미한다. 하지만 저염분 순응 시 미량 증가하는 IT 전구체 mRNA는 초기 삼투조절에 미치는 역할이 미미함을 보여준다.
도시지역에 시공되는 지하차도 구조물은 지리적 특성상 지하수위의 영향을 받기 쉽다. 그러나 지하차도 구조물 설계 시에는 일괄적인 지하수위를 적용하여 설계를 수행하는 경우가 많으며 이는 과소 또는 과다 설계를 초래할 수 있다. 따라서 본 연구에서는 보다 신뢰도 높은 지하수위 예측을 통해 지하차도 구조물의 합리적인 부력설계 방향을 제시하고자한다. 특히, 최근 친환경적인 개발 개념인 LID 기법을 도입한 투수 포장 적용에 따른 물순환 특성 변화가 지하차도 구조물에 어떠한 영향을 미치는지에 대해 검토하였다. 이를 위해 개발 전, 개발 후, 투수포장 적용에 의한 지표면 불투수 특성 변화가 침투량 및 지하수위 변화에 미치는 영향 분석과 지하차도 안정성을 검토하는 일련의 수치해석을 수행하였다. 해석결과 지표면의 변화가 지하수위 변화를 유발하고 지하 구조물 안정성에 영향을 줄 수 있음을 확인하였다. 따라서 지하차도 및 지하구조물의 최적 설계를 위해서는 지표면 유출 특성을 고려한 적절한 지하수위 예측 및 적용이 필요할 것으로 판단된다.
비파괴적, 비관입적으로 지반 및 구조물의 전단강성 구조를 파악할 수 있는 SASW 기법은 여러 토목분야에서 성공적으로 적용이 되어왔다. 그러나 SASW 기법은 그 기법상의 제약으로 인해 실험이 행해지는 측선의 하부구조가 수평으로 균질하다고 하는 가정을 하여야만 한다. 이러한 수평 다층 구조의 가정은 포장 구조체, 터널 라이닝 등의 토목 구조물의 건전도 검사의 경우에 있어서 반드시 합리적이라고 할 수는 없다. 즉, 지반조사 측선 방향으로의 변이성 평가를 높은 해상도로 수행하여야 할 경우에 기존의 SASW 실험으로 만족스러운 결과를 얻는 것은 용이하지 않다. 최근에는 지반 및 구조물의 건전도 상태를 연속적으로 평가하는 GPR과 같은 비파괴 검사의 중요성이 부각되고 있는 실정이기에, 본 연구에서는 기존의 SASW 실험을 보완하여 지반 조사 측선 방향으로의 전단강성의 연속적 평가가 가능한 토모그래픽 SASW 기법을 새로이 개발하였다. 이러한 토모그래픽 SASW 기법의 개발로 조사대상 매질의 전단강성의 변화에 관한 거리-깊이의 2차원적 컨투어(contour) 도표(토모그래피)의 표현이 가능하게 되어 SASW 기법의 적용성이 토건구조물의 건전도 평가 영역에서 확대되게 되었다. 본 연구에서는 새로이 제안된 토모그래픽 SASW 기법의 타당성을 평가하기 위하여 강사법으로 형성한 모래지반의 횡방향 및 깊이 방향으로의 균질성을 조사하였다. 토모그래픽 SASW 실험으로 모래지반의 전단강성의 변화정도를 용이하게 파악할 수 있었으며, 전단강성의 길이-깊이 방향에 대한 컨투어 도표는 강사법에 사용한 강사기의 문제점을 파악하는데 도움이 되었다. 이러한 모래 지반에서의 전단강성의 평가 실험으로 본 연구에서 제안한 토모그래픽 SASW 실험의 타당성 및 적용성을 확인할 수 있었다.
Due to climate change, coastal areas are being flooded with torrential rain, typhoons, and tsunamis. In addition, non-point source pollutants (NPSs) that accumulated on the ground, streets, and buildings during the dry season are washed off by rain and stormwater runoff, which adds to the damage associated with environmental pollution, e.g., pollution that makes its way into the ocean. Recently, low impact development (LID) has been considered as a means of controlling water circulation and NPSs. In the coastal area, permeable blocks have been constructed mainly to reduce the flood damage caused by waves. Some important design factors that must be considered to ensure long-term performance are the permeability coefficient, clogging, and the efficiency of the removal of total suspended solids (TSS), but currently there are no standardized design criteria or testing techniques that are used worldwide. Herein, we analyzed the permeability coefficient and the TSS removal efficiency tendency according to the permeability area ratio with an easily-detachable, permeable block filled with calcinated yellow soils as the filter media. Our lab-scale tests indicated that, when the permeability area ratio was 25%, the reduction of the permeability coefficient after clogged was 11%, which was a significant decrease compared to other cases. Permeability persistence increased when the permeability area ratio increased from 50% to 75%. The TSS removal efficiency decreased as the permeability area ratio increased. Our pilot-scale test indicated that the TSS removal efficiency was more than 80% higher in all cases. We also found that the permeability persistence was excellent as the permeability area ratio increased, and, in actual construction, it is effective to set 5.3% of the total area as permeable area in terms of permeability and economic feasibility.
Porous concrete has large continuous voids of 20-30 % by volume, and this concrete is attractive as environmental material in Japan i.e. permeable road pavement, river bank protection with vegetation and green roof system which influence thermal environment. It is necessary to confirm the frost resistance when constructing porous concrete structure in cold region. However applicable test method and evaluation criterion of porous concrete has not defined yet. Therefore, the object of this study is to investigate the frost resistance of porous concrete and this investigation attempts to address this concern by comparing 4 kinds of specified freezing and thawing tests methods (JIS A1148 procedure A/B and RILEM CIF/CDF test) in consideration of actual environment. RILEM freeze-thaw tests are different from JIS A1148 freeze-thaw tests, which are widely adopted for evaluating the frost resistance of conventional concrete in Japan, in water absorption, cooling rate, length of freezing and thawing period, and number of freezing and thawing cycles. RILEM CIF test measures internal damage and is primarily applicable for pure frost attack. CDF test is appropriate for freeze-thaw and de-icing salt attack. JIS A1148 procedure A/B showed extremely low frost resistance of porous concrete if the large continuous voids were filled with water and the ice expansion in the large continuous voids set in during cooling. Frost resistance of porous concrete was improved by mixing coarse aggregate (G7) which particle size is smaller and fine aggregate in JIS freezing and thawing tests. RILEM CIF/CDF test showed that freeze-thaw and de-icing resistance of porous concrete was seems to be superior in that of conventional concrete.
Over the past 30 years, the business effects of the improvement project at black spot have been decreasing since 2010, with a reduction in the amount of government spending, coupled with proposing a uniform improvement plan. In order to promote more efficient improvement projects, it is necessary to evaluate the efficiency of local governments and improve the business methods of local governments with low efficiency. However, more sophisticated efficiency analysis methods are needed. Because in previous studies have been limited to the analysis of effects before and after the project through the simple before-after analysis. For this purpose, this study analyzed the efficiency of improvement project at black spot by local governments in Gyeonggi-do using DEA to compare and analyze efficiency in various fields. As a result, Goyang, Seongnam, Paju, Hanam and Yangju showed high efficiency local governments. For local governmetns with low efficiency, the improvement projets to improve efficiency were divided into civil engineering work, structure work, pavement work, additional work and transportation work, and the appropriate construction ratios of each local government were analyzed and presented.
본 연구에서는 콘크리트 교량 바닥판의 열화를 비파괴시험인 지표투과레이더(GPR)를 이용하여 평가하는 방법을 개발하였다. 콘크리트 교량 바닥판의 유전 상수를 계산하기 위하여 비접촉식 GPR 안테나를 이용하여 2층 구조체에 적용할 수 있는 확장형 공통중간점 방법을 개발하였다. 콘크리트 교량 바닥판의 열화 깊이와 열화 상태는 콘크리트 교량 바닥판의 유전 상수와 표면대비 평균 유전상수비를 이용하여 평가하였다. 제안된 방법을 검증하기 위하여 GPR 현장 시험을 공용수명이 오래된 콘크리트 교량에서 실시하였다. 시험 결과 새로 제안된 방법을 이용하여 추정된 두께와 열화 깊이가 어느 정도 신뢰성을 가지는 것으로 나타났다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.