• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.108-113
• /
• 1994

Active noise control technique has superior performance in low frequency ranges(50 .approx. 400Hz) to the conventional passive noise control technique. For the feasibility of active noise control, it is required to develop a controller which can implement control algorithm on real-time. In this study, therefore, real-time controller is developed using TMS320c25, high speed digital processor. Unlike conventional DSP board of complete ADD ON type, it is possible for the developed controller to interface with the other computer system easily by series communication for the convenience of program development. Furthermore it is designes to be separated readily as a control device. Active noise control of duct system is implemented ti evaluate a performance of developed device. Active noise control of duct system is implemented to evaluate a performance of developed controller using filtered-x LMS algorithm.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.6
• /
• pp.384-390
• /
• 2012

Passive sonars employ DEMON(Detection of Envelope Modulation on Noise) processing to extract propeller information from the radiated noise of underwater targets. However, the conventional DEMON processing suffers from the interference of tonal signals because it extracts propeller signals and some types of tonal signals as well. If there are some tonals in the frequency band for DEMON processing, the conventional DEMON processing may additionally extract frequency informations originated from the interaction between different tonals. In this paper, we propose a modified DEMON processing, which can eliminate the interference of the tonals. The proposed algorithm removes tonals in DEMON processing band before demodulation processing, hence results the robustness to the interference of the tonals. Some numerical simulations demonstrate the improved performance of the proposed algorithm against the conventional algorithm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.30-40
• /
• 2002

A 2.45GHz double-balanced modified Gilbert-type CMOS up-conversion mixer design is introduced, where the PMOS current-reuse bleeding technique is demonstrated to be efficient in improving conversion gain, linearity, and noise performance. An LO buffer is included in the mixer design to perform single-ended to differential conversion of the LO signal on chip. Simulation results of the design based on careful modeling of all active and passive components are examined to explain in detail about the characteristic improvement and degradation provided by the proposed design. Two kinds of chips were fabricated using a standard $0.35\mu\textrm$ CMOS process, one of which is the mixer chip without the LO buffer and the other is the one with it. The measured characteristics of the fabricated chips are quite excellent in terms of conversion gain, linearity, and noise, and they are in close match to the simulation results, which demonstrates the adequacy of the modeling approach based on the macro models for all the active and passive devices used in the design. Above all the benefits provided by the current-reuse bleeding technique, the improvement in noise performance seems most valuable.

• Journal of the Institute of Convergence Signal Processing
• /
• v.21 no.4
• /
• pp.162-169
• /
• 2020

In this paper, we attempted a qualitative understanding of mutual injection locking without rigorous mathematics, and analyzed the proposed mutual injection locked light source. Also, a low-cost WDM-PON light source based on mutual injection locking using two unpolarized Fabry-Perot Laser Diodes (F-P LDs), was implemented. The RIN (Relative Intensity Noise) characteristic for the wavelength change of the F-P LD was measured, and when the variable wavelength range was 2.07 nm, it showed a RIN of at least -110 dB/Hz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.86-93
• /
• 2008

A low-power, low-noise, highly-linear hybrid balun circuit is proposed for 2.4-GHz fully differential CMOS direct conversion receivers. The hybrid balun is composed of a passive transformer and loss-compensating auxiliary amplifiers. Design issues regarding the optimal signal splitting and coupling between the transformer and compensating amplifiers are discussed. Implemented in $0.18{\mu}m$ CMOS process, the 2.4 GHz hybrid balun achieves 2.8 dB higher gain and 1.9 dB lower noise figure than its passive counterpart and +23 dBm of IIP3 only at a current consumption of 0.67 mA from 1.2 V supply. It is also examined that the hybrid balun can remarkably lower the total noise figure of a 2.4 GHz fully differential RF receiver only at a cost of 0.82 mW additional power dissipation.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.104-109
• /
• 2021

In this paper, we experimentally demonstrate a self-seeding FP-LD (Fabry Perot Laser Diode) to verify the possibility of a new tunable light source that can be used in WDM-PON (Wavelength Division Multiplexing - Passive Optical Network) system. The conventional implementation of WDM-PON using a tunable light source has a disadvantage that the center wavelength of the AWG (Arrayed Waveguide Grating) device and the tunable light source must be precisely aligned. However, the proposed tunable light source has the advantage that the tunable wavelength is automatically aligned with the center wavelength of the AWG as well as simple structure. The implemented tunable light source had a tunable band of about 14 nm or more, and the maximum RIN (Relative Intensity Noise) of about -124 dB/Hz, which showed the possibility of modulating 10 Gb/s signal by an external modulator.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.12
• /
• pp.106-113
• /
• 1997

While driving, the low frequency interior noise below 200Hz causes the main component that irritates the auditory acoustic sense. But these passive control methods bring out increment in cost and weight of the vehicle and result in low efficiency. Recently, various ANC(Active Noise Control) methos to suppress the low frequency noise began to launch into application. In this study, we implemented the active noise control system for passenger vehicle to cancel the engine booming noise using DSP-based control unit, 4 micorphones, and 2 speakers. We used MEFX-LMS (Multiple Error Filtered X-Least Mean Square) algorithm since it can be easily implemented in real time. Also, MEFX-RLS algorithm was taken to enhance the suppression of the harmonic components of the engine booming noise inspite of its computational complexity. The performance of two adaptive algorithms were analyzed with experimental resutls.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.8 s.101
• /
• pp.891-896
• /
• 2005

On the basis of theoretical studies on the effect of the cylinders attached to semi-infinite screens, the tangential sound power-transport parallel to the surface of the attached cylinder is minimized by means of a secondary sound field, which is generated from a part of the attached cylinder. The numerical study shows the possibility of deflecting the incident sound by minimizing the sound field of the upper sections. The acoustical shadow region was more pronounced in both near- and far-field compared to the passive case with rigid surface, i.e. without active control. For a relatively wide frequency range it was possible to enhance shielding effects only with few secondary sources and error microphones. In this paper effects of control parameters on the actively controlled sound field near the top edge of noise barriers are studied. Results of numerical study and model measurements are shown and discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.525-529
• /
• 2002

ANC technic can overcome the limited performance of passive noise control at the low frequency range. But it has the local quiet control region in general. In this paper, it is discussed that the global noise control in a circular duct using a ring type smart foam and a porous material. LMS algorithm and RLS algorithm are used to find optimal orders of cancellation path. Experiments are performed to compare the efficiency of RLS algorithm with that of LMS algorithm.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.957-959
• /
• 2005

A noise reduction equipment in power systems was device combined in a passive element such as the form of L, R and C. A analysis of frequency characteristics for the transformer models shall be considered the additional capacitance between the windings($C_{ps}$), terminals($C_s$), and winding-ground($C_g$). A noise in transformer is modeled by take account into the different frequency. In case of the high frequency, transformer windings with stray capacitance have lower impedance. Therefore a noise is transferred from primary winding to secondary winding. Noise Cut Transformer(NCT) was the noise reduction device and was normally single phase two-winding type transformer. We analyzed frequency characteristics using the nodal network analysis with the equivalent circuit and the simulation of the MATLAB.