• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.199-206
• /
• 2003

Particle-size distribution in soils is one of the most fundamental physical properties of soils. One of the latest developments in the study of particle-size distributions has focused on the use of fractal theories. In this study, the fragmentation fractals were used for determining the characteristics of the particle-size distribution curve. It was shown that the mass-size distribution method was more practical than the cumulative number-size distribution method. From the co-relation between fractal dimensions($D_{tot}$) and the coefficient of uniformity($C_{u}$), there was a sharp increase in fractal dimensions for $C_{u}$<4, but fractal dimension converged the single value for $D_{u}$$\geq$6. Fractal dimensions were affected by small sized particles for $C_{c}$$\geq$3 and large sized particles for $C_{c}$/<3. As a result of the analysis of the influence of the effective size($D_{10}$), it was observed that the changes of $D_{tot}$/ were nominal beyond the effective size.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.721-724
• /
• 2006

In this study, particle size distribution of cement powder system were adjusted using the blast furnace slag powder, Blaine $2250cm^2/g\;and\;8300cm^2/g$, which easy to adjust particle size distribution to examine how particle size distribution of the binder has an effect on rheological properties of the cement paste. In addition, the relationship between n-value of Rosin-Rammler function and plastic viscosity were discussed. All measured flow curves represented thixotropy behavior and the hysteresis area was smaller for the more added coarse particle. When the combination was based on a ratio of $20{\sim}25vol%$ fine particles, $30{\sim}40vol%$ OPC and $40{\sim}45vol%$ coarse particles of the total volume, a high fluidity and low yield strength was achieved.

• Asian-Australasian Journal of Animal Sciences
• /
• v.5 no.1
• /
• pp.55-61
• /
• 1992

To determine the effect of time after feeding on distribution of particle size of digesta in the gastrointestinal tract, 16 sheep given orchardgrass first cut hay were slaughtered at 2, 8, 16 and 24 hours after feeding and digesta in diverse sites of the tract were sieved into four fractions of particle size larger than $1180{\mu}m$, 300-1180, 45-300 and less than 45. Following results were obtained: 1) In the reticulo-rumen, the proportion of particles larger than $1180{\mu}m$ decreased with the time after feeding, while the other particle size fractions did not change with time after feeding. 2) In the post-ruminal alimentary tract, the proportion of particles larger than $1180{\mu}m$ was significantly smaller than that in the reticulo-rumen and distribution of fractions of every particle size stayed consistently at about the same level irrespective of the time after feeding. 3) In the cecum, the fraction of particle size less than $45{\mu}m$ appeared to be selectively retained when the passage rate was considered.

• The Journal of Korea Robotics Society
• /
• v.12 no.3
• /
• pp.332-338
• /
• 2017

As an interpretation of existing jamming effects, the main variables affecting the increase in stiffness due to jamming are known as system density, jamming density, pressure, and particulate temperature. The main variable, jamming density, is closely related to the distribution of particle size and contact properties such as particle shape and friction. However, the complexity of these variables makes it difficult to fully understand the mechanism of the jamming effect. In this paper, we focus on the jamming effects of particles that have more elastic properties than particles such as sand and coffee powder, which are commonly used as constituent particles of existing jamming, in order to reduce complicated factors such as temperature and concentrate on jamming effects based on elastic characteristics of particles. It was experimentally explored the possibility of increasing stiffness by mixing particles of different sizes rather than simply increasing the bending stiffness by controlling the particle size. Through simulations and experiments, we found a case where the stiffness of each particle size distribution is larger than the stiffness of each particle size.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.3
• /
• pp.370-374
• /
• 2003

Cell cracking method using a non-collision was evaluated for the possibility of new red ginseng grinding technique. Based on particle size distribution analysis by 1size shaker, the ratios of 100 mesh penetrated particles were 94.9% for hammer mill (group A) and 95.6% for cell crack (group B). The ratio of 120 mesh penetrated particle of group A was higher than that in group B. The particle size distributions for 100 mesh non-penetrated Powder between 2 groups were not significantly different, and particle size distribution analysis by laser scattering analyzer showed that the particle size ranges were 0.77~128.07 ${\mu}{\textrm}{m}$ for group A and 4.24~180.07 ${\mu}{\textrm}{m}$ for group B. The Particle size distribution in group A was more broad than that in group B. The mean particle size in group B was larger than that in group A, while the standard deviation of particle size distribution in group B was less than that in group A. Structural surface characteristics, in group A, particle size distribution was broad and the distribution curve was amorphous. The structure of individual particles was similar to unequal stone which was roughly grinded and had soft cotton-like surface. In the contrary, in group B, particle size distribution was relatively narrow and also individual size particles were ubiquitously distributed. The structure of individual particles was unequal cut stone shape.

• Journal of Environmental Health Sciences
• /
• v.44 no.4
• /
• pp.360-369
• /
• 2018

Objectives: Outdoor tobacco smoke can penetrate into the indoor environment through cracks in the building envelope. This study aimed to characterize the particle size distribution of infiltrated secondhand smoke (SHS) through the gap in a single glazed and a secondary glazed window according to pressure differences in a chamber. Methods: Two polyvinyl chloride sliding windows were evaluated for infiltration, one with a glazed window and the other with a secondary glazed window. Each window was mounted and sealed in a polycarbonate chamber. The air in the chamber was discharged to the outside to establish pressure differences in the chamber (${\Delta}P$). Outdoor smoking sources were simulated at a one-meter distance from the window side of the chamber. The particle size distribution of the infiltrated SHS was measured in the chamber using a portable aerosol spectrometer. The particle size distribution of SHS inside the chamber was normalized by the outdoor peak for fine particles. Results: The particle size distribution of SHS inside the chamber was similar regardless of window type and ${\Delta}P$. It peaked at $0.2-0.3{\mu}m$. Increases in particulate matter (PM) concentrations from SHS infiltration were higher with the glazed window than with the secondary glazed window. PM concentrations of less than $1{\mu}m$ increased as ${\Delta}P$ was increased inside the chamber. Conclusions: The majority of infiltrated SHS particles through window gap was $0.2-0.3{\mu}m$ in size. Outdoor SHS particles infiltrated more with a glazed window than with a secondary glazed window. Particle sizes of less than $1{\mu}m$ were associated with ${\Delta}P$. These findings can be a reference for further research on the measurement of infiltrated SHS in buildings.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.147-154
• /
• 1995

Abnormal grain growth behavior of BaTiO3 ceramics with controlling of particle size distribution of calcined powder was investigated. The particle size distribution was controlled by changing the calcining temperature or by using of classification and regrinding process. With broadening of the normallized size distribution in calcined powder, it showeda normal grain growth behavior in sintered body due to an increase of volume fraction of seed grain in the calcined powder. It was supposed that the seed grains could easily contact each other for the rapid grain growth during sintering process and resulted in fast switching-over from abnormal to normal grain growth stage.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.43-44
• /
• 2017

In this study, mortar strength was measured by grinding oyster shell and changing the particle size distribution. For the experiment, the oyster shells were processed to a fine aggregate size of 10mm or less. In this experiment, seven particle size distribution conditions were selected and tested. Because oyster shells are different in density from sand, their volume ratios were calculated and converted to mass ratios of 1: 3. The strength test was carried out one day after the steam curing.

• Elastomers and Composites
• /
• v.55 no.1
• /
• pp.20-25
• /
• 2020

The effect of the isocyanate index (NCO index) on the particle size and particle size distribution of a waterborne polyurethane dispersion (WPUD) with polycarbonate-diol was determined. The WPUDs were prepared using a conventional acetone process with polycarbonate-polyol (M_n = 2028), 4,4'-methylenebis(cyclohexyl isocyanate) (H₁₂MDI), 2,2-bis(hydroxymethyl) propionic acid (DMPA), and dibutyltin dilaurate catalyst. At NCO index values below 1.5, the number average particle diameter of the WPUDs significantly increased with the NCO index, whereas the particle diameter slightly varied at higher NCO indexes. The dependency of the WPUD viscosity on the NCO index exhibited similar behavior to that of the particle size. The relative values of the full width at half maximum of the WPUD particle distribution curves at various NCO indexes were not influenced by the NCO index.

• Textile Coloration and Finishing
• /
• v.15 no.5
• /
• pp.327-332
• /
• 2003

In this study, the polyurethane microcapsules for non-aqueous dyeing containing iron oxide and disperse dyes were prepared by in-situ polymerization method using hexamethylene diisocyanate(HDI) with ethylene glycol(EG). And the size, shape, and particle size distribution of microcapsules prepared were investigated. The size and shape of microcapsule were observed by optical microscope and scanning elecron microscope. The particle size distribution was analyzed by particle size analyzer. The microcapsule size and its distribution were largely effected by the existance of surface active agent in the system. When a surfactant did not exist in the system, the size distribution of microcapsules prepared was much uneven. By adding a surfactant, this phenomenon was disappeared. And the size of microcapsule was also effeced by the hydrophobicity of core material(disperse dye). It was considered due to the difference of dispersity of core materials. And the size of microcapsule prepared was inversely proportional to the stirring speed.