• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.2
• /
• pp.9-17
• /
• 2007

A Green's function approach based on the laminate theory is adopted for solving the two-dimensional unsteady temperature field and the associated thermal stresses in an infinite plate made of functionally graded material (FGM). All material properties are assumed to depend only on the coordinate x (perpendicular to the surface). The unsteady heat conduction equation is formulated into an eigenvalue problem by making use of the eigenfunction expansion theory and the laminate theory. The eigenvalues and the corresponding eigenfunctions obtained by solving an eigenvalue problem for each layer constitute the Green's function solution for analyzing the two-dimensional unsteady temperature. The associated thermoelastic field is analyzed by making use of the thermal stress function. Numerical analysis for a FGM plate is carried out and effects of material properties on unsteady thermoelastic behaviors are discussed.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.737-746
• /
• 1989

After Ba-ferrite powders synthesized hydrothermally and its heated powders were dissolved partially with HCl treatment time, the BaO/Fe2O3 mole ratio of dissolved solutions and powders were measured by AAS, also, lattice constants, particle morphology and magnetic properties in HCl treated, heated and no-heated Ba-ferrite powders were abtained by means of XRD, SEM and VSM, respectively. From above analysis results, the effect of Ba/Fe mole ration in suspension(as starting material) on the BaO/Fe2O3 composition and particle characteristics of products were investigated, and the effect of heat treatment on magnetic properties of products examined. The composition, lattice constant and crystal phase of products depend on the Ba/Fe mole ratio in suspension. Ba content in surface or outer part of Ba-ferrite powder is higher than inner and heterogeneous, and the excess Ba ions in the inner part of particle move into the outer by heating, so that the mole ratio of BaO/Fe2O3 in the more jinner approaches more to the stoichiometric composition 1 : 6. The crystallinity, coercivity and saturation magnetization of products are increased by heat treatment, and the heat-treated samples synthesized hydrothermally in lower temperature are appreciated to have better powder characteristics.

• Korean Journal of Hydrosciences
• /
• v.3
• /
• pp.61-79
• /
• 1992

In oder to predict the dispersion of a thermal discharge with strong turbulent and buoyant effects, the development of a numerical model using turbulence model and its application are significantly increased. In this study, a three-dimensional steady-state model for the surface discharge heated water into quiescent water body is developed. For the model closure of turbulent terms the four-equation turbulence model is used. For economic mumerical simulation, the elliptic governing equations are transformed to the partially parabolic equations. In general, the simulated results by the present model agree well with the experimental results by Pande and Rajratnam (1977). The model characteristics are presented in comparison with the predicted results from the two-eqauation turbulence model by McGuirk and Rodi (1979).

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.78-84
• /
• 2016

In this work, finite element investigations were carried out to optimize reverse drawing process design for manufacture of high-capacity aluminum liner used in fuel cell vehicle. The tensile tests with aluminum alloy Al6061 annealed at $350^{\circ}C$ were carried out to obtain the flow stresses. In order to estimate more accurate flow stresses after necking, the flow stresses were estimated from the comparison of load vs. displacement curves which were obtained from experimental and simulation results of tensile tests. In case of finite element analyses of reverse drawing processes, it was focused on the effects of process designs such as punch and die designs, blank holding force, drawing ratio and the clearance between the punch and blank holder on the generation of wrinkle and fracture of the blank and partially heated punch. However, it was revealed that experimental results still show the fracture at the end of 2nd drawn cup, although partially heated punch is used. Nevertheless, the drawn cup can be used because the sufficient length of the drawn cup for the next flow forming process and spinning process was obtained.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2249-2260
• /
• 1995

An experiment of close contact melting of phase-change medium partially filled in an isothermally heated horizontal cylinder is performed which involves the volume expansion of liquid induced by the solid-liquid density difference. The solid-liquid interface motion and the free surface behavior of liquid were reported photographically. The experimental results show that the curvature of upper solid-liquid interface varied to flat as melting progresses. In addition to the varying interface shape, the melting rate increases with the lower initial height of solid and the free surface height of liquid increases linearly. The experimental results of molten mass fraction were expressed in a function of dimensionless time Fo.Ste$^{3}$4/ and agreed well with the analytical solutions.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.321-329
• /
• 2019

A series of poly(hyroxyamide)s (PHAs) was prepared by direct polycondensation reaction of 4,4'-(2,3-pyridinedioxy)dibenzoic acid and/or isophthalic acid with 3,3'-dihydroxybenzidine. The yield percentages of the products were high, and the inherent viscosities of the polymer in DMAc solution at 35℃ were 0.31-0.59 dL/g. All PHA polymers were found to be soluble in polar aprotic solvents such as DMAc, DMSO, NMP, and DMF. On the other hand, LiCl was required to dissolve IPHA-1 in aprotic solvents. Poly(benzoxazole)s (PBOs) were partially soluble in conc-H₂SO₄; IPBO-4, -5, and -6 were partially soluble in NMP only when LiCl was added to the solution, and the solution was heated. The PBO polymers showed a maximum weight loss in the temperature range of 654-680℃, and the char yields at 900℃ under nitrogen atmosphere exceeded 63%.

• Korean Membrane Journal
• /
• v.5 no.1
• /
• pp.10-17
• /
• 2003

1,3,5-Sustitituted polyphenylene type dendrimers were synthesized. The dendrimer was heated in cone. H$_2$SO$_4$ at 120$^{\circ}C$. The reaction mixture was precipitated to ether after simple filtration to get para-sulfonated dendrimer as the chief product. To give mechanical properties to the sulfonated dendrimer, it was partially cross-linked with phenyl ether in the medium of P$_2$O$\sub$5/ and CH$_3$SO$_3$H.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.635-639
• /
• 1998

When the low pressure injection molded parts are debinded by wicking and subsequent thermal pyrolysis the optimum transition point from wicking to thermal pyrolysis is just after the completion of the constant wicking rate period. Even when the partially debinded parts were heated at 5$^{\circ}C$/min after reaching the 1st falling rate period the debinding defects such as distortion and cracks were not found.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.4 no.2
• /
• pp.115-118
• /
• 1975

The constriction thermal resistance due to the floor supports in the Ondol floor heating system was investigated. The resistance has significant influence on the uniformity of floor surface temperature and heat flux through the floor. The heat flux decreased as much as $30\%$ for the geometry of the same channel and support areas.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.2999-3007
• /
• 1994

The unsteady numerical simulations have been presented for the laminar natural convection in a partially open compartment. Computations were performed within the domain of the compartment in order to show the thermal radiation and the partially opening effects on the flow fields and heat transfer characteristics. The results were shown for different Planck numbers(0.05~5) and opening ratios(0.25~0.75) being fixed with Ra=$10^5$ and Pr=0.71. Considering the flow which is buoyancy driven from the heated wall, and the buoyancy is not much affected by the further outside region from the opening, the numerical computations have been performed without an outer region by the particular boundary treatments on the flow velocity and temperature at the different partial openings. The confined numerical domain reduced the CPU time and the memory of computer. P-1 approximation of radiative transfer equation was employed with Marshak type boundary conditions along with the pseudo-black body approximation at the partial openings. The numerical results clearly show that the natural convective flow and heat transfer are much affected by increase of thermal radiation particularly from the initial state. When thermal radiation is not much affecting the flow ($PL{\le}1$), it was found that thermal radiation effects are almost negligible.