• Transactions on Electrical and Electronic Materials
• /
• v.14 no.6
• /
• pp.317-320
• /
• 2013

Partial discharge resistance for the epoxy systems with two diluents was investigated in the rod-plane electrodes arrangement, and the effect of electric frequency on the partial discharge resistance was also studied. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and 1,4-butanediol diglycidyl ether (BDGE) or polyglycol (PG) as a reactive diluent was introduced to the DGEBA system, in order to decrease the viscosity of the DGEBA epoxy system. BDGE was acted as a chain extender, and PG acted as a flexibilizer, after the curing reaction. To measure the partial discharge resistance, 5 kV alternating current (ac) with three different frequencies (60, 500 and 1,000 Hz) was applied to the specimen in a rod-plane electrode arrangement, at $30^{\circ}C$. PG had a good effect, while BDGE had a bad effect on the partial discharge resistance of the DGEBA system, regardless of the electric frequency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.6
• /
• pp.1026-1031
• /
• 2016

Neat Epoxy, nano alumina composites, micro alumina composites and multi-nano alumina composites were prepared and experiment were performed to measure their partial discharge resistant characteristics. The partial discharge resistance obtained for the microcomposites, nanocomposites and multi-nanocomposites are compared with those of unfilled epoxy and with GDE amount for surface modifier. It was observed that compare multi-nano alumina composites to micro alumina composites, the partial discharge resistance to degradation gets improved considerably. The improvement in the degradation resistance is attributed to the interface intension between the nano alumina composites and GDE, micro alumina and epoxy neat.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.9
• /
• pp.1189-1196
• /
• 2018

7 type composites (40, 45, 50, 55, 60, 65, and 70 wt.%)were prepared for the environmentally friendly GIS Spacer. Five kinds of samples were prepared for optimization of the filler content ratio (MS: MA = 1: 9, 3: 7, 5: 5, 7: 3, 9: 1) of epoxy / microsilica and microalumina. As a result of evaluation of the partial discharge resistance characteristic, surface erosion is generally slowed down as the fill amount of micro silica is increased. Also, partial discharge resistance characteristics for the development of insulating materials with optimal mixing ratios of heterologous showed a higher partial resistance of discharge and a decrease in erosion, as the filler content ratio of micro silica was larger. In the future, various researches such as electrical, mechanical, and thermal studies will be needed to develop insulating materials that can commercialize power devices in environmentally friendly insulating gas.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1694-1699
• /
• 2013

Frequency accelerated partial discharge resistance (PDR) aging of epoxy/layered silicate nanocomposite with 1.5wt % additions of layered silicate was investigated in comparison with that of epoxy without layered silicate in terms of PD(partial discharge) erosion depth. It was found that the change in the erosion depth is far smaller in specimens with layered silicate than those without layered silicate nano particles. Frequency acceleration can be done from 60Hz to 1000Hz. But the depth of erosion is less proportional to frequency. Acceleration factor is almost 2 times between 500Hz and 1000Hz, but it is much less than about 8.3 times between 60Hz and 500Hz. This superior PD resistance is caused by the presence of nanofillers, anano-effect due to closely packed nanofillers, and strong chemical bonds at layered silicate nanofillers /resin interfaces.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.2
• /
• pp.61-69
• /
• 2020

Purpose: Zirconia fixed partial dentures with mandibular 2^nd premolar and 2^nd molar as abutments are fabricated and then the effects of inter-abutment distance on fracture resistance of zirconia fixed partial dentures is studied. Materials and Methods: The materials used in this study are Cameleon S zirconia block and S2 zirconia block, which are divided into CS Group and S2 Group applying different inter-abutment distance for each material, and the sintered zirconia fixed partial denture was luted to the epoxy resin die using a temporary luting cement, and then the fracture resistance was measured by placing a 6 mm diameter hardened steel ball on the occlusal surfaces of the pontics and applying pressure at a cross head speed of 1.0 mm/min on a universal testing machine with a load cell of 5.0 kN. Results: The fracture resistance of zirconia fixed partial dentures is not significantly affected by inter-abutment distance The fracture resistance of zirconia fixed partial dentures in CS Group was significantly higher in 15 mm of inter-abutment distance than in 13 mm and 17 mm of inter-abutment distance (P < 0.05). The fracture resistance of zirconia fixed partial dentures in S2 Group was not significantly different between the three groups (P > 0.05). Conclusion: The fracture resistance of zirconia fixed partial dentures with mandibular 2^nd premolar and 2^nd molar as abutments does not significantly affected by the inter-abutment distance.

• The Journal of Korean Physical Therapy
• /
• v.32 no.5
• /
• pp.273-276
• /
• 2020

Purpose: The purpose of this study was to investigate the effects of the resistance conditions on the electromyography (EMG) activity ratio of vastus medialis oblique (VMO) and vastus lateralis (VL) muscle during partial lunge exercise in healthy subjects in order to suggest the basic data of exercise intervention for such as patients with patellofemoral pain syndrome (PFPS). Methods: The participants of this study were healthy twenty two people with no knee pain, limitation of motion and past history of operation at lower extremity. The participants performed three types of lunge 1) no resistance, 2) anterolateral 45° resistance and 3) lateral 90° respectively. The EMG activity of the VMO and VL were recorded by surface EMG and the measured data normalized by the %MVIC value was analyzed by repeated measured ANOVA. Results: The results showed that the VMO/VL EMG activity ratio during lunge with anterolateral 45° resistance was significantly higher than with no resistance and lateral 90° resistance (p<0.05). There was no significant difference in VMO, VL, and VMO/VL muscle activity between male and female subjects (p>0.05). Conclusion: This study suggests that partial lunge exercise with anterolateral 45° resistance can increase the VMO/VL muscle activity in healthy subjects. This result could be used as basic data to develop therapeutic exercise programs such as PFPS patients.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.5
• /
• pp.275-281
• /
• 2019

Anodization is widely used to enhance the properties of aluminum, such as hardness, electric resistance, abrasion resistance, corrosion resistance etc. But these properties can be enhanced with additional process. According to the partial crystallization of oxide layer with post heat treatment, enhanced hardness can be expected with partial crystallization. In this study, post heat treatments were applied to the anodized aluminum alloys of Al6061 to achieve the partial crystallization, and crystallizations were evaluated with the reduced breakdown voltages. Interestingly, remarkable enhanced hardness (21~29%), abrasion resistance (26~62%), and reduced breakdown voltage (24~44%) were observed for the sulfuric acid anodized samples when we annealed the anodized samples with 1hour post heat treatment at $360^{\circ}C$. For the Al5052 alloys, a lot of cracks were observed when we applied the post heat treatment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.250-265
• /
• 1999

Quality and distribution of the TEA(Total Enclosed Area), TSA(Twine Surface Area), solidity ratio and resistance according to the partial nets of the midwater trawl net were examined through experiment at the sea to standardize a design of the midwater trawl net.The results can be summarized as follows;1. The TEA, TSA and resistance of the trawl net were increased definitely according to increasing the scale of the trawl net, and this is the most important factor to design the trawl net.2. As the result of analysis of the distributions of the bag net was smaller than the others. Because TEA for rear end of the wing net is decreased suddenly, we can judge that the trawl net was towed irregularly. 3. The resistance distribution of the partial net was increased suddenly from central part of the bag net and was showed large value in the codend.4. The resistance of the net from the position one of three to gab net and codened charged 75% at all resistance of net.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.4
• /
• pp.292-294
• /
• 1996

To investigate the relationship between two tetracycline resistance ($Tc^r$) plasmids, the 24.82-kb pKHl and the 4.44-kb pKH6, of Staphylococcus aureus isolated in Korea, cloning of the 4570-bp HindIII fragment into pBluescript II $KS^+$ after partial digestion of the $Tc^r$ plasmid pKHl with HindIII and sequence determination of that fragment were carried out. Analysis of the sequences revealed that the 4570-bp HindIII fragment contained a 4011-bp fragment of the small $Tc^r$ plasmid pKH6 flanked by the partial sequences of IS431mec. It was concluded from the above result that the pKHl was produced by integration of the partial sequence of the pKH6 into another plasmid via IS431mec.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.89-91
• /
• 2010

Partial discharge (PD) resistances were investigated for three types of samples: original epoxy resins, epoxy micro composites with and without the silane processing, and mixture composites with micro and nano particles. The PD was applied to these materials using rod, gap, and plane electrodes. The partial discharge resistance found in the micro composites was better than that found in the original epoxy resin. Moreover, the mixture composites of $SiO_2$ nano and micro particles had much larger resistances than the original epoxy resin or microcomposites. It can be regarded that this excellent property was due to the fact that the nano particles have a dense structure between the micro particles.