• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.395-400
• /
• 2015

Obtaining the parameters for PID controllers based on limit cycle information for the process in a relay controlled feedback loop has become an accepted practical procedure. If the form of the plant transfer function is known, exact expressions for the limit cycle frequency and amplitude can be derived so that their measurements, assumed error free, can be used to calculate the true parameter value. In the literature, parameter estimation for an assumed form of the plant transfer function has generally been considered for disturbance free cases, except a recently published work of the author. In this paper additional simulation results are reported on exact parameter estimation from relay autotuning under static load disturbances.

• Journal of the Optical Society of Korea
• /
• 제14권2호
• /
• pp.104-108
• /
• 2010

We proposed an axis transformation technique which reveals a distance parameter directly from optical scanning holography (OSH). After synthesis of a real-only spectrum hologram and power fringe adjusted filtering, we transform an original frequency axis to a new frequency axis using interpolation. In the new frequency axis, the filtered hologram has a single frequency which is linearly proportional to the distance parameter. Thus, the inverse Fourier transformation of the filtered hologram gives a delta function pair in the new spatial axis. Finally, we extract the distance parameter by detecting the location of the delta function pair.

• Journal of the Korean Data and Information Science Society
• /
• 제17권4호
• /
• pp.1375-1386
• /
• 2006

In life testing, the lifetimes of test units under the usual conditions are so long that life testing at usual conditions is impractical. Testing units are subjected to conditions of high stress to yield informations quickly. In this paper, the inferences of parameters on the three step-stress accelerated life testing are studied. The two-parameter exponential distribution with a failure rate function that a log-quadratic function of stress and the tempered failure rate model are considered. We obtain the maximum likelihood estimators of the model parameters and their confidence regions. A numerical example will be given to illustrate the proposed inferential procedures.

• 전자공학회논문지B
• /
• 제31B권9호
• /
• pp.27-35
• /
• 1994

It is known that a unified phase I-phase II semi-infinite optimization algorithm with a steerign parameter performs better than the original unified phase I-phase II algorithm. In this paper, the effect of the steering parameter is analized and a new algorithm is presented based on the facts that when the point x is far away from the feasible region, reaching to the feasible region is more important than minimizing the cost functio and that when the point x is near the region, it is more efficient to try to reach the feasible region and to minimize the cost function concurrently. It is also important to consider the relationship between the feasible direction and the gradient of the cost function. Even though changing the steering parameter does not change the rate of convergence of the algorithm, it is shown from examples that given new algorithm is more efficient than the previous ones.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.199-199
• /
• 2000

Most of linear time-varying(LTV) systems except special cases have no general solution for the dynamic equations. Thus, it is difficult to design time-varying controllers in analytic ways, and other control design approaches such as robust control have been applied to control design for uncertain LTI systems which are the approximation of LTV systems have been generally used instead. A robust control method such as quantitative feedback theory(QFT) has an advantage of guaranteeing the stability and the performance specification against plant parameter uncertainties in frozen time sense. However, if these methods are applied to the approximated linear time-invariant(LTI) plants which have large uncertainty, the designed control will be constructed in complicated forms and usually not suitable for fast dynamic performance. In this paper, as a method to enhance the fast dynamic performance, the approximated uncertainty of time-varying parameters are reduced by the proposed QFT parameter-scheduling control design based on radial basis function (RBF) networks for LTV systems with bounded time-varying parameters.

• 소음진동
• /
• 제9권5호
• /
• pp.891-898
• /
• 1999

The purpose of Superconducting Magnetic Bearing Flywheel Energy Storage System (SMB-FESS) is to store unused nighttime electricity until it is needed during daytime. An analytical model of the SMB-FESS is necessary to identify the system behavior. At first, we have to model the superconducting magnetic bearing. Modeling the SMB is same as estimating the bearing parameter. The theoretical modal parameter is calculated through the equation of motion and the experimental modal parameter is estimated through the impact testing (modal testing). The bearing parameter is searched by using the non-linear least square method until the theoretical result corresponds to the experimental result. The suggested modeling method is verified by comparing experimental and analytical frequency response function.

• 한국물환경학회지
• /
• 제24권4호
• /
• pp.430-435
• /
• 2008

In order to design Non-point source management, the aspect of statistical features of the entire precipitation data should be focused since non-point source discharge is driven by continuous rainfall runoffs. 3-parameter mixed exponential probability density function is used to establish urban stormwater capture curve instead of previous single-parameter exponential PDF. Then, recent 10-year data in Busan are applied to establish the curve. The result shows that 3-parameter mixed PDF gives better resolution.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.134-136
• /
• 2001

In this paper, using equivalent circuit of BLDC motor in the 30W class, process of modeling the BLDC motor and calculating the parameter is shown. Through run-down-test and measuring back EMF, torque, speed and ampere, parameter that transfer function requires was gotten. In this result, for step response of BLDC motor, comparing the actual result obtained by circuit experiment with the simulation result obtained by substituting this parameter into the transfer function, it was established that process calculating parameters in this study is proper.

• 대한조선학회논문집
• /
• 제46권6호
• /
• pp.562-568
• /
• 2009

Hull form generation and variation methods to be mainly discussed in this study are based on the fairness optimized B-Spline form parameter curves (FOBFC). These curves can be used both as indirect modification function for variation and as geometric entities for hull form generation. The flexibility and functionality of geometric control technique play the most important role for the success of hull form optimization. This study shows the hydrodynamic optimization process and the characteristics of optimum design hull forms of a 14,000TEU containership and 60K LPG carrier. SHIPFLOW has been used as a CFD solver and FS-Framework as a geometric modeler and optimizer.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.289-294
• /
• 1998

The distributed-parameter structures expressed with the partial differential equations are considered as the infinite-dimensional dynamic system. For implementation of a controller in multivariate systems, it is necessary to derive the state-space reduced order model. By the eigensystem realization algorithm, we can yield tile subspace system with the Markov parameters derived from the measured frequency response function by the inverse discrete Fourier transformation. We also review the necessary conditions for the convergence of the approximation system and the error bounds in terms of the singular values of Markov-parameter matrices. To determine the natural frequencies and modal damping ratios, the modal coordinate transformation is applied to the realization system. The vibration test for a smart structure is performed to provide the records of frequency response functions used in the subspace system realization.