• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1494-1499
• /
• 2003

Kinematic calibration is a process whereby the actual values of geometric parameters are estimated so as to minimize the error in absolute positioning. Measuring all components of Cartesian posture, particularly the orientation, can be difficult. With partial pose measurements, all parameters may not be identifiable. This paper proposes a new device that can be used to identify all kinematic parameters with partial pose measurements. Study is performed for a six degree-of-freedom fully parallel Hexa Slide manipulator. The device, however, is general and can be used for other parallel manipulators. The proposed device consists of a link with U joints on both sides and is equipped with a rotary sensor and a biaxial inclinometer. When attached between the base and the mobile platform, the device restricts the end-effector's motion to five degree-of-freedom and can measure position of the end-effector and one of its rotations. Numerical analyses of the identification Jacobian reveal that all parameters are identifiable. Computer simulations show that the identification is robust for the errors in the initial guess and the measurement noise.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.76-80
• /
• 2001

A binary parallel robot manipulator uses actuators that have only two stable states being built by stacking variable geometry trusses on top of each other in a long serial chain. Discrete characteristics of the binary manipulator make it impossible to analyze an inverse kinematic problem in conventional ways. We therefore introduce new definitions of workspace and inverse kinematic solution, and the apply a genetic algorithm to the newly defied inverse kinematic problem. Numerical examples show that our genetic algorithm is very efficient to solve the inverse kinematic problem of binary robot manipulators.

• Journal of Mechanical Science and Technology
• /
• v.16 no.8
• /
• pp.1053-1063
• /
• 2002

This paper presents a robust nonlinear controller for a f degree of freedom (DOF) parallel manipulator in the task space coordinates. The proposed control strategy requires information on orientations and translations in the task space unlike the joint space or link space control scheme. Although a 6 DOF sensor may provide such information in a straightforward manner, its cost calls for a more economical alternative. A novel indirect method based on the readily available length information engages as a potential candidate to replace a 6 DOF sensor. The indirect approach generates the necessary information by solving the forward kinematics and subsequently applying alpha-beta-gamma tracker With the 6 DOF signals available, a robust nonlinear task space control (RNTC) scheme is proposed based on the Lyapunov redesign method, whose stability is rigorously proved. The performance of the proposed RNTC with the new estimation scheme is evaluated via experiments. First, the results of the estimator are compared with the rate-gyro signals, which indicates excellent agreement. Then, the RNTC with on-line estimated 6 DOF data is shown to achieve excellent control performance to sinusoidal inputs, which is superior to those of a commonly used proportional-plus-integral-plus-derivative controller with a feedforward friction compensation under joint space coordinates and the nonlinear controller under task space coordinates.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.260-270
• /
• 1994

With the prevalent use of robot, the interests in moving speed of robot have been increasing for the purpose of upgrading performance of production. But the faster robot manipulator moves, the worse working accuracies are. And mechanical vibration is more and more serious with the increment of the moving speed of robot. So, the study on the cause and control method of robot vibration is one of the points of issue in robotics. This paper focuses on the vibration of 3 DOF parallel link drive mechanism robot. We assume that links of robot manipulator are `rigid' and joints are `flexible elements'. Governing equations of robot system including controller, servo amplifier, D.C servo motor, transmission with elasticity, and manipulator dynamics are derived. On the basis of modelling, we define `controller stiffness' by the proportional gain of controller and `stiffness of transmission'. Numerical and experimental research is performed to study vibration phenomena of robot induced from the variation of these two defined stiffnesses, and its results are shown.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.46-51
• /
• 2004

This paper presents an adaptive control method based on parameter linearization for incompletely restrained wire-suspended mechanisms. The main purpose of this control method is utilizing it in a walking assist service robot for elderly people. This method is computationally simple and requires neither end-effector acceleration feedback nor inversion of estimated inertia matrix. In the proposed adaptive control law, mass, moment of inertia and external force and torque on the end-effector are considered as components of parameter adaptation vector. Nonlinear simulation for walking an elderly shows the effectiveness of the parameter adaptation law.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.1039-1046
• /
• 2000

This paper introduces the control and measurement of a double parallel robot manipulator applied for unknown geometric surface grinding. A measurement system is developed to recognize a grinding path by a vision camera and to observe a grinding load by a current sensor. With the measured fusion information, an intelligent controller identifies the unknown geometric surface and moves the robot along the grinding path with a constant grinding load.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.56-65
• /
• 1997

This paper presents the robot program for propeller grinding. A robot manipulator is constructed by combining a parallel and a serial mechanism to increase high sitffness as well as workspace. The robot program involves inverse/direct kinematics, velocity mapping, Jacobian, and etc. They are cerived in efficient formulations and implemented in a real time control. A velocity control is used to measure the hight of a propeller blade with a touch probe and a position control is performed to grind the surface of the blade.

• Journal of Biomedical Engineering Research
• /
• v.20 no.4
• /
• pp.401-407
• /
• 1999

A microsurgery telerobotic system has been developed to aid surgeons from physiological tremor, eye stram, hand tremor, contagious and radioactive hazard. This paper identifies four general areas of advanced microsurgery and analyzes the motion, tools, accuracy and applying forces with respect to microsurgery tasks, and proposes the criteria to design the microsurgical robot. The analysis of microsurgery can be helpful to clarify some basic concept and design of surgical robots. Based on this analysis results, we propose an efficient in-parallel-platform manipulator having a special kinematic structure suitable for microsurgery.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.397-400
• /
• 1992

Many dynamic control have been proposed; however, most of them are limited within stage of simulation study. The main reason is that the computations required for inverse dynamics are far beyond the ability of the present commercially available microprocessors. In this paper, In order to achieve real-time processing in robot dynamic control, a parallel processing computer for robot dynamic control is implemented using two transputer. Two transputer compute two degree of freedom robot. The transputer is a special purpose MPU for parallel processing. Transputers are used in networks to build a high performance concurrent system. A network of transputers and peripheral controllers is constructed using point-to-point communication. To gain most benifit from the transputer architecture, the whole system is programmed in OCCAM which is a high level language for concurrent applications. This control algorithm is applied to the RHINO SCARA type manipulator. We could taked about 438.6 microseconds to compute robot dynamic with two-processors.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.149-156
• /
• 1995

본 연구의 목적은 6자유도를 가진 병렬형 메니퓰레이터의 기구학적 해석을 하는데 있다. 일반적인 산업용 로봇의 구조는 링크가 직렬로 연결된 형상을 하고 있으며 이러한 형태는 넓은 작업공간의 확보와 유연성이 뛰어난 장점이 있는 반면에 각 링크의 오차가 메니퓰레이터의 끝단에서 누적되어 나타나게 되고 구동렬이 증가하게 되는 단점을 지니고 있다. 이러한 단점을 극복하기 위하여 정밀한 위치제어가 필요한 경우에는 병렬형 형태의 링크를 지닌 구조를 사용하고 있다. 병렬형 메니퓰레이터의 역기구학적 해석은 비교적 단순한 데 반하여 정기구학적 해 석은 비선형 방정식의 형태로 나타나며 해석적으로 그 해를 구하기가 쉽지 않다. 본 연구에서는 6자유도를 지닌 병렬형 메니퓰레이터의 기구학적 해석을 수행하였으며 예제를 통하여 검정하였다.