• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.185-187
• /
• 2000

Fault current is flowed into 154/23kV M. Tr when line-to-ground fault occurs in power system. NGR(Neutral Grounded Reactor) is set up in order to prevent M.Tr fault by limiting magnitude of fault currents. Here, disconnection of NGR causes voltage increase by L-C resonance and line-to-ground fault in an unearthed system results in voltage increase at healthy phases. So Over Voltage Ground Relay(OVGR) is used for tripping M.Tr. Also, buses at second phases of M.Trs are all connected with section circuit breakers closed for the purpose of parallel operation and load shedding. In case of speciality buses are comprised of power cable in part for GIS connection. When no-load charged cable or bus is open by a section CB, unbalanced voltage charged on the bus is induced. Also discrepant opening time for circuit breakers on different phases gives rise to unbalanced zero sequence voltage. It was observed that this zero sequence voltage detected in the 22.9kV P.T (Potential Transformer for bus) mal-operated 59GT and tripped M.Tr. The zero sequence voltage of which vanishing time is longer than relay operating time came out by EMTDC simulation. Also, it was shown that the voltage waves of actual test are similar to those of simulation. On the basis of above results, R-C circuit complement on the relay without any effect on a power system made operating time of the relay longer than vanishing time of distorted waves. Consequently, operating time of the relay was delayed and magnitude of distorted waves was decreased by increasing time constant of the relay.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4A
• /
• pp.200-207
• /
• 2003

This paper proposes a CDMA receiver structure with time-shifted m-sequence orthogonal reception process, and analyzes the output SNR performance and the characteristics of the orthogonal receiver. This structure can be simply implemented with the converntional receiver adding an additional integrator path in parallel and an adder sums the conventional path and the new path output signals. The structure provides to reference user signal not only increment of signal component but also perfect orthogonal characteristic, canceling the accumulated cross-correlated value out to zero between the reference user and other user signals. Hence, the proposed structure can be applied for channel impulse response measurement, and used for multi-user interference signal cancellation and channel capacity increment by flexible structural inter-working operation of the added path, connection or disconnection, to conventional receiver structure.

• School Mathematics
• /
• v.13 no.3
• /
• pp.447-468
• /
• 2011

For the instruction of units dealing with the conic section, the most important factor that we need to consider is the connections. In other words, the algebraic approach and the geometric approach should be instructed in parallel at the same time. In particular, for the students of low proficiency who are not good at algebraic operation, the geometric approach that employs visual representation, expressing the conic section's characteristic in a dynamic manner, is an important and effective method. For this, during this research, to suggest the importance of dynamic visual representation based on GeoGebra in teaching Quadratic Curve, we taught an experimental class that suggests the instruction method which maximizes the visual representation and analyzed changes in the representation of students by analyzing the part related to the unit of a parabola from units dealing with a conic section in the "Geometry and Vector" textbook and activity book.

• International Journal of Highway Engineering
• /
• v.16 no.6
• /
• pp.51-57
• /
• 2014

PURPOSES : An conventional method for electric power generation is converting thermal energy into mechanical energy then to electrical energy. Due to environmental issues such as global warming related with $CO_2$ emission etc., were the limiting factor for the energy resources which resulting in extensive research and novel technologies are required to generate electric power. Thermal energy harvesting using thermoelectric generator is one of energy harvesting technologies due to diverse advantages for new green technology. This paper presents a possibility of application of the thermoelectric generator's application in the direct exchange of waste solar energy into electrical power in road space. METHODS : To measure generated electric power of the thermoelectric generator, data logger was adopted as function of experimental factors such as using cooling sink, connection methods etc. Also, the thermoelectric generator、s behavior at low ambient temperature was investigated as measurement of output voltage vs. elapsed times. RESULTS : A few temperature difference between top an bottom of the thermoelectric generator is generated electric voltage. Components of an electrical circuit can be connected in various ways. The two simplest of these are called series and parallel and occur so open. Series shows slightly better performance in this study. An installation of cooling sink in the thermoelectric generator system was enhanced the output of power voltage. CONCLUSIONS : In this paper, a basic concepts of thermoelectric power generation is presented and applications of the thermoelectric generator to waste solar energy in road is estimated for green energy harvesting technology. The possibility of usage of thermoelectric technology for road facilities was found under the ambient thermal gradient between two surfaces of the thermoelectric module. An experiment results provide a testimony of the feasibility of the proposed environmental energy harvesting technology on the road facilities.

• Journal of KIISE:Computer Systems and Theory
• /
• v.36 no.5
• /
• pp.351-359
• /
• 2009

Recently with increase of data in the Internet, platform technologies that can process huge data effectively such as Google platform and Hadoop are regarded as worthy of notice. In this kind of platform, there exist network I/O overheads to send task outputs due to the MapReduce operation which is a programming model to support parallel computation in the large cluster system. In this paper, we suggest applying of TIPC (Transparent Inter-Process Communication) protocol for reducing network I/O overheads and increasing network performance in the distributed computing environments. TIPC has a lightweight protocol stack and it spends relatively less CPU time than TCP because of its simple connection establishment and logical addressing. In this paper, we analyze main features of the Hadoop-based distributed computing system, and we build an experimental model which can be used for experiments to compare the performance of various protocols. In the experimental result, TIPC has a higher bandwidth and lower CPU overheads than other protocols.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.241-246
• /
• 2002

We have performed the current and voltage loading tests of resistive superconducting fault current limiters (SFCLS) based on $YBa_2$$Cu_3$$O_{7}$(YBCO) films with the diameter of 2 inch. The SFCL consists of meander-type YBCO stripes covered with 200 nm Au layer grown in situ for current shunt and heat dispersion at hot spots. The minimum quench current of an SFCL unit was about 25 Apeak. Seven SFCL units were connected in parallel fur the current load ing tests at power source of 100 $V_{rms}$ $/2,000A_{rms}$. This SFCL units had maximum limiting current of 170 Apeak during the fault instant and then successfully controlled the fault current below 100 Apeak within 1~2 msec after short circuit. Increased short current also reduced the quench completion time with little change of current limiting characterization. We connected six SFCL units in series fur the voltage loading tests at power source of $1,200 V_{rms}$/170 $A_{rms}$ at this time. The shunt resistors were inserted into each SFCL unit to eliminate power imbalance originated from serial connection of SFCL units. Each SFCL unit was quenched simultaneously during the fault condition. The current increased up to 40 $A_{peak}$ and decreased to 14 $A_{peak}$ after 3 cycles. Quench was completed within 1 msec after the fault. We confirmed operating characteristics of 140 kVA($120 A_{rms}$ $\times$ 1,200 $V_{rms}$) SFCL and presented the manufacturing possibility of 3.3 kV SFCL using 4 inch YBCO films.BCO films.lms.

• Journal of Internet Computing and Services
• /
• v.10 no.4
• /
• pp.199-211
• /
• 2009

Recent advancements in wireless networks have enabled support for mobile applications to transfer data over heterogeneous wireless paths in parallel using data striping technique [2]. Traditionally, high performance data transfer requires tuning of multiple TCP sockets, at sender's end, based on bandwidth delay product (BDP). Moreover, traditional techniques like Automatic TCP Buffer Tuning (ATBT), which balance memory and fulfill network demand, is designed for wired infrastructure assuming single flow on a single socket. Hence, in this paper we propose a buffer tuning technique at senders end designed to ensure high performance data transfer by striping data at transport layer across heterogeneous wireless paths. Our mechanism has the capability to become a resource management system for transport layer connections running on multi-homed mobile host supporting features for wireless link i.e. mobility, bandwidth fluctuations, link level losses. We show that our proposed mechanism performs better than ATBT, in efficiently utilizing memory and achieving aggregate throughput.

• Journal of the Korea Society for Simulation
• /
• v.15 no.4
• /
• pp.97-105
• /
• 2006

Popular content stored within the Internet may be convenient to download via modern 3G connections, but costly due to a fee charged by telecommunication providers on the basis of the amount of data transferred. This paper presents a network in which several mobile devices, called the peers, cooperate to download their assigned portion of the content using a 3G connection in order to reduce the overall cost. Then, the peers exchange their assigned portion of the content with other peers via a wireless ad hoc network and the peers reconstruct the whole content using the exchanged portion. This paper focuses on the per-peer based distribution method, and presents the performance comparison with a similar method, called the per-packet distribution method. Both methods are designed to reduce packet collisions while content is exchanged. The simulation result indicates that the per-peer based method outperforms the per-packet based method, and approximately 90% of the telecommunication cost is saved with as few as 10 peers.

• Journal of Home Health Care Nursing
• /
• v.11 no.1
• /
• pp.23-32
• /
• 2004

Purpose: The purpose of this research is to give basic data about a way of connection to individual centers and vitalization of visiting nursing program on Busan. Method: The research is done with survey for eight hospitals. sixteen public heath centers, forty-six social welfare centers to be practised visiting nursing program on Busan for actual condition of that. Results: 1. The average nursing career is below 5-10 years. But visiting nursing career is below 3 years(70%) in hospital. public, public heath center, and heath center. 2. Hospitals coverage of visiting nursing service is city as a whole. Whereas public heath center and social welfare center covered some local area. 3. Client of visiting nursing service possess in order of alone lived elderly, person in uncomplete movement, a disabled person, and a chronic disease person. 4. The main service in visiting is patient assessment, basic nursing activity, and treatment nursing activity with medication care, B.P check, dressing, bedsore care, catheter care and exchange, fluid therapy. Particularly, the hospital runs parallel to basic care and treat care in 100%. The social service center has 65.0% in a patient assessment and basic nursing activity. 5. The concern about services connecting with other center is very high. Conclusion: Actual conditions of visiting nursing program on Busan, which is presented in this study. The results of this study will become the pillar of visiting nursing program planning and application.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.4
• /
• pp.593-605
• /
• 2014

In this paper, we propose the efficient HW/SW co-design method of light-weight cryptography such as HIGHT, PRESENT and PRINTcipher using GEZEL. At first the symmetric cryptographic algorithms were designed using the GEZEL language which is efficiently used for HW/SW co-design. And for the improvement of performance the HW optimization theory such as unfolding, retiming and so forth were adapted to the cryptographic HW module conducted by FSMD. Also, the operation modes of those algorithms were implemented using C language in 8051 microprocessor, it can be compatible to various platforms. For providing reliable communication between HW/SW and preventing the time delay the improved handshake protocol was chosen for enhancing the performance of the connection between HW/SW. The improved protocol can process the communication-core and cryptography-core on the HW in parallel so that the messages can be transmitted to SW after HW operation and received from SW during encryption operation.