• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.1
• /
• pp.62-67
• /
• 2008

Biocomposite was fabricated with biodegradable polymer and natural fiber that has potential to be used as replacement for glass fiber reinforced polymer composite with the benefits of low cost, low density, acceptable specific strength, biodegradability, etc. Until now, mostly natural cellulosic fibers on land have been used as reinforcement for biocomposite. The present study focused on investigating the fabrication and the characterization of biocomposite reinforced with red algae fibers from the sea. The bleached red algae fiber (BRAF) showed very similar crystallinity to the wood cellulose. It has high stability against thermal degradation (maximum thermal decomposition temperature of 359.3$^{\circ}C$) and thermal expansion. Biocomposites reinforced with BRAF have been fabricated by a compression molding method and their mechanical and thermal properties have been studied. The storage modulus and the thermomechanical stability of PBS (polybuthylenesuccinate) matrix are markedly improved by reinforcing with the BRAF. These results indicate that red algae fiber can be used as an excellent reinforcement of biocomposites, which are sometimes called as "green-composites" or "eco-composites".

• Computers and Concrete
• /
• v.26 no.6
• /
• pp.515-531
• /
• 2020

Due to the construction difficulties of steel reinforced concrete (SRC), a new composite structure of steel and steel fiber reinforced concrete (SSFRC) is proposed for solving construction problems of SRC. This paper aims to investigate the bond properties and composition of interfacial bond stress between steel and steel fiber reinforced concrete. Considering the design parameters of section type, steel fiber ratio, interface embedded length and concrete cover thickness, a total of 36 specimens were fabricated. The bond properties of specimens were studied, and three different methods of calculating interfacial bond stress were analyzed. The results show: relative slip first occurs at the free end; Bearing capacity of specimens increases with the increase of interface embedded length. While the larger interface embedded length is, the smaller the average bond strength is. The average bond strength increases with the increase of concrete cover thickness and steel fiber ratio. And calculation method 3 proposed in this paper can not only reasonably explain the hardening stage after the loading end curve yielding, but also can be applied to steel reinforced high-strength concrete (SRHC) and steel reinforced recycled coarse aggregate concrete (SRRAC).

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.05a
• /
• pp.33-55
• /
• 2007

This article portrays special cellulose fibers, which are designed to be a functional additive and a carrier for papermaking chemicals. The first part of the presentation deals with the micronized $ARBOCEL^{(R)}$ cellulose fibers, which are used as a functional paper/paperboard additive. In particular as a bulk and speed aid. The detailed description of the micronized $ARBOCEL^{(R)}$ fibers, their function and effects on papermaking process and paper products are given. The second part of the study describes the concept of fiber-based papermaking chemicals. A new generation of fiber-based papermaking chemicals were presented for the first time at the PTS Pulp Technology Symposium 2005, and then several articles were published in various magazine in Asia ("Paper Asia"), the US ("Pulp & Paper"). and Europe ("Wochenblatt fuel Papierfabrikation"). The information generated quite an interest in the paper industry. Extensive studies of these papermaking additives have been made recently, new information obtained, and the compounds have gained more recognition in the industry. The company J. Rettenmaier und Soehne developed a group of fiber-based papermaking additives. They include combination of fibers with sizing agents, starch, fluorochemicals, minerals, biocides and some others. This article presents in-depth study of the AKD modified micronized cellulose as an example of the fiber-based papermaking chemicals concept. The material of the present paper is based mostly on the results of the pilot paper machine study at the Paper Research Institute PTS (Heidenau, Germany), and includes case studies from the mills, which used $ARBOCELPLUS^{(R)}-AKD$ compounds. It should be noted that the $ARBOCELPLUS^{(R)}$ compounds were not designed to replace traditional additives in paper industry. They should rather be used in those areas, where application of "normal" chemicals is especially problematic

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.15-22
• /
• 2015

The crop production technologies keep in improving and the cultivation becomes more standardization owing to the significant developments of various agricultural materials. The artificial soil and base system for root could be one of the major technologies for the modern cultivation especially for controlled horticulture. Although the perlite, cocopeat, and peat moss are the major components of the artificial soil and are broadly used for various application, there is a great need for the new alternative materials for overcoming the low nutrition and the possible shortage of raw materials. In this study, the application of oil palm EFB fiber as an alternative materials for artificial soil especially for the seeding pad components was evaluated. The changes in the structural properties and the functional properties such as moisture holding properties were compared by laboratory produced seeding pads with different mixture of oil palm EFB fiber. The addition of fibrillated EFB fiber resulted in the significant increase in durability of the seeding pad, which showed the possible application of EFB fiber to the seeding pad instead of the wood fiber (UBKP). The moisture holding properties and the germination condition characteristics of the EFB fiber showed the slight less than those of the cocopeat, which require more sophisticated study for improving the functional properties of seeding pad made of the EFB fiber.

• Analytical Science and Technology
• /
• v.32 no.1
• /
• pp.7-16
• /
• 2019

The objective of this study was the development of a discrimination model for the cultivational origin of paper mulberry bast fiber and Hanji using near infrared (NIR) and mid infrared (MIR) spectroscopy combined with partial least squares discriminant analysis (PLS-DA). Paper mulberry bast fiber was purchased in 10 different regions of Korea, and used to make Hanji. PLS-DA was performed using pre-treated FT-NIR and FT-MIR spectral data for paper mulberry bast fiber and Hanji. PLS-DA of paper mulberry bast fiber and Hanji samples, using FT-NIR spectral data, showed 100 % performance in cross validation and the confusion matrix (accuracy, sensitivity, and specificity). The discrimination models showed four regional groups which demonstrated clearer separation and much superior score plots in the NIR spectral data-based model than in the MIR spectral data-based model. Furthermore, the discrimination model based on the NIR spectral data of paper mulberry bast fiber had highly similar score morphology to that of the discrimination model based on the NIR spectral data of Hanji.

• Composites Research
• /
• v.28 no.1
• /
• pp.1-5
• /
• 2015

In this paper the influence of fiber orientation of basalt and carbon inter-ply fabrics on the flexural properties of hybrid composite laminates was experimentally investigated. Four types of basalt/carbon/epoxy inter-ply hybrid composite laminates with varying angle ply orientation of reinforced basalt fiber and fixed orientation of carbon fiber were fabricated using hand lay-up technique. Three point bending test was performed according to ASTM 7264. The fracture surface analysis was carried out by scanning electron microscope (SEM). The results obtained from the four laminates were compared. Lay-up pattern of $[0B/+30B/-30B/0C]_S$ exhibits the best properties in terms of flexural strength and flexural modulus. Scanning electron microscopy results on the fracture surface showed that the interfacial de-bonding between the fibers and epoxy resin is a dominant fracture mode for all fiber lay-up schemes.

• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.155-161
• /
• 2003

This paper presents experimental and analytical results of glass fiber-reinforced concrete (GFRC) and polypropylene fiber-reinforced concrete (PERC) to investigate the relationship between tensile strength and compressive strength based on the split cylinder test (ASTM C496) and compressive strength test (ASTM C39). Experimental studies were performed on cylinder specimens having 150 mm in diameter an 300 mm in height with two different fiber contents (1.0 and 1.5％ by volume fraction) at ages of 7, 28 and 90 days. A total of 90 cylinder specimens were tested including specimens made of the plain concrete. The experimental data have been used to obtain the relationship between tensile strength and compressive strength. A representative equation is proposed for the relationship between tensile strength and compressive strength of fiber-reinforced concrete (FRC) including glass and polypropylene fibers. There is a good agreement between the average experimental results and those calculated values from the proposed equation.

• Communications for Statistical Applications and Methods
• /
• v.18 no.3
• /
• pp.301-317
• /
• 2011

Statistical and probabilistic behaviors of fibers forming fiber webs of all kinds are of great significance in the determination of the uniformity and physical properties of the webs commonly found in many industrial products such as filters, membranes and non-woven fabrics. However, in studying the spatial geometry of the webs the observations must be theoretically as well as experimentally confined within a specified unit area. This paper provides a general theory and framework for computer simulation for quantifying the fiber segments bounded by the unit area in consideration of the "edge effects" resulting from the truncated length segments within the boundary. The probability density function and the first and second moments of the length segments found within the counting region were derived by properly defining the seeding region and counting region.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.563-568
• /
• 2002

This paper is a fundamental study on the mechanical properties of the high performance concrete confined with metal lath, glass and carbon fiber laterally. According to the results, it shows that the compressive strength increases by 9%, 8% and 6% in metal lath carbon fiber and glass fiber in case of W/B 30% respectively. In case of W/B 30% and 40%, flecxural strength shows largely in order of carbon fiber, metal lath, glass fiber. In strain-stress curve with the kinds of material for lateral confinement, while brittleness failure occurs in plain concrete just after maximum load, it is improved in some degree in confined concrete due to increase of the strain by increase of toughness. But, elastic modulus shows the similar tendency between confined concrete and plain concrete. Length change ratio by drying shrinkage shows little a bit in order of carbon fiber, glass fiber and metal lath due to confinement.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.4
• /
• pp.73-78
• /
• 2004

The conventional SLT(Shear Lag Theory) which has been proven that it can not provide sufficiently accurate strengthening predictions in elastic regime when the fiber aspect ratio is small. This paper is an extented work to improve it by modifying the load transfer mechanism called NSLT(New Shear Lag Theory), which takes into account the stress transfer across the fiber ends and the SCF(Stress Concentration Factor) that exists in the matrix regions near the fiber ends. The key point of the model development is to determine the major controlling factor among the material and geometrical coefficients. It is found that the most affecting factor is the fiber/matrix elastic modulus ratio. It is also found that the proposed model gives a good result that has the capability to correctly predict the elastic properties such as interfacial shear stresses and local stress variations in the small fiber aspect ratio regime.