DOI QR코드

DOI QR Code

Interfacial bond properties and comparison of various interfacial bond stress calculation methods of steel and steel fiber reinforced concrete

  • Wu, Kai (College of Civil and Transportation Engineering, Hohai University) ;
  • Zheng, Huiming (College of Civil and Transportation Engineering, Hohai University) ;
  • Lin, Junfu (College of Civil and Transportation Engineering, Hohai University) ;
  • Li, Hui (College of Civil and Transportation Engineering, Hohai University) ;
  • Zhao, Jixiang (College of Civil and Transportation Engineering, Hohai University)
  • Received : 2019.10.25
  • Accepted : 2020.11.27
  • Published : 2020.12.25

Abstract

Due to the construction difficulties of steel reinforced concrete (SRC), a new composite structure of steel and steel fiber reinforced concrete (SSFRC) is proposed for solving construction problems of SRC. This paper aims to investigate the bond properties and composition of interfacial bond stress between steel and steel fiber reinforced concrete. Considering the design parameters of section type, steel fiber ratio, interface embedded length and concrete cover thickness, a total of 36 specimens were fabricated. The bond properties of specimens were studied, and three different methods of calculating interfacial bond stress were analyzed. The results show: relative slip first occurs at the free end; Bearing capacity of specimens increases with the increase of interface embedded length. While the larger interface embedded length is, the smaller the average bond strength is. The average bond strength increases with the increase of concrete cover thickness and steel fiber ratio. And calculation method 3 proposed in this paper can not only reasonably explain the hardening stage after the loading end curve yielding, but also can be applied to steel reinforced high-strength concrete (SRHC) and steel reinforced recycled coarse aggregate concrete (SRRAC).

Keywords

Acknowledgement

This work is supported by National Natural Science Foundation of China (Grant No.51208175) and the Fundamental Research Funds for the Central Universities (Grant No. B200202067).

References

  1. ACI 381-14 (2014), Building Code Requirements for Structural Concrete, American Concrete Institute, Farmington Hills, MI, USA.
  2. Avanaki, M.J., Hoseini, A., Vandani, S., de Santos, C. and de la Fuente, A. (2018), "Seismic fragility curves for vulnerability assessment of steel fiber reinforced concrete segmental tunnel linings", Tunn. Undergr. Sp. Tech., 78, 259-274. https://doi.org/10.1016/j.tust.2018.04.032.
  3. Boyd, P.F., Cofer, W.F. and Mclean, D.I. (1995), "Seismic performance of steel-encased concrete columns under flexural loading", ACI Struct. J., 92(3), 355-364.
  4. Chen, L.H., Dai, J.X., Jin, Q.L., Chen, L.F. and Liu, X.L. (2015), "Refining bond-slip constitutive relationship between checkered steel tube and concrete", Constr. Build. Mater., 79, 153-164. https://doi.org/10.1016/j.conbuildmat.2014.12.058.
  5. Choi, C.S. and Bae, B.I. (2019), "Effectiveness of steel fibers as hoops in exterior beam-to-column joints under cyclic loading", ACI Struct. J., 116(2), 205-219.
  6. Choi, S.W., Oh, B.K., Park, J.S. and Park, H.S. (2016), "Sustainable design model to reduce environmental impact of building construction with composite structures", J. Clean Prod., 137, 823-832. https://doi.org/10.1016/j.jclepro.2016.07.174.
  7. Choi, Y., Hajyalikhani, P. and Chao, S.H. (2018), "Seismic performance of innovative reinforced concrete coupling beam-double-beam coupling beam", ACI Struct. J., 115(1), 113-125.
  8. Ding, Y.N., You, Z.G. and Jalali, S. (2011), "The composite effect of steel fibres and stirrups on the shear behaviour of beams using self-consolidating concrete", Eng. Struct., 33(1), 107-117. https://doi.org/10.1016/j.engstruct.2010.09.023.
  9. Dinh, H.H., Parra-Montesinos, G.J. and Wight, J.K. (2010), "Shear behavior of steel fiber-reinforced concrete beams without stirrup reinforcement", ACI Struct. J., 107(5), 597-606.
  10. Elmy, M.H. and Nakamura, S. (2017), "Static and seismic behaviours of innovative hybrid steel reinforced concrete bridge", J. Constr. Steel Res., 138, 701-713. https://doi.org/10.1016/j.jcsr.2017.08.025.
  11. GB/T 228.1-2010 (2010), Metallic Materials-Tensile Testing-Part 1: Method of Test at Room Temperature, Standards Press of China, Beijing, China.
  12. GB/T 706-2008 (2008), Hot Rolled Section Steel, Standards Press of China, Beijing, China.
  13. Ghazizadeh. S. and Cruz-Noguez, C.A. (2018), "Damage-resistant reinforced concrete low-rise walls with hybrid GFRP-steel reinforcement and steel fibers", J. Compos. Constr., 22(2), 04018002. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000834.
  14. Hs, H.L., Hsieh, J.C. and Juang, J.L. (2004), "Seismic performance of steel-encased composite members with strengthening cross-inclined bars", J. Constr. Steel Res., 60(11), 1663-1679. https://doi.org/10.1016/j.jcsr.2004.04.002.
  15. Hui, C., Zhu, Y.Z., Cao, W.L. and Wang, Y.Q. (2016), "Seismic experiment and analysis of rectangular bottom strengthened steel-concrete composite columns", Steel Compos. Struct., 20(3), 599-621. http://dx.doi.org/10.12989/scs.2016.20.3.599.
  16. Hung, C.C. and Hu, F.Y. (2018), "Behavior of high-strength concrete slender columns strengthened with steel fibers under concentric axial loading", Constr. Build. Mater., 175, 422-433. https://doi.org/10.1016/j.conbuildmat.2018.04.201.
  17. Ibrahim, H.A., Fahmy, M.F.M. and Wu, Z.S. (2018), "Numerical study of steel-to-FRP reinforcement ratio as a design-tool controlling the lateral response of SFRC beam-column joints", Eng. Struct., 172, 253-274. https://doi.org/10.1016/j.engstruct.2018.05.102.
  18. Jang, S.J., Jeong, G.Y. and Yun, H.D. (2018), "Use of steel fibers as transverse reinforcement in diagonally reinforced coupling beams with normal- and high-strength concrete", Constr. Build. Mater., 187, 1020-1030. https://doi.org/10.1016/j.conbuildmat.2018.08.063.
  19. JG/T 472-2015 (2015), Steel fiber reinforced concrete. Standards Press of China, Beijing, China.
  20. Lim, D.H. and Nawy, E.G. (2005), "Behaviour of plain and steel-fibre-reinforced high-strength concrete under uniaxial and biaxial compression", Mag. Concrete Res., 57, 603-610. https://doi.org/10.1680/macr.2005.57.10.603.
  21. Liu, C., Lv, Z.Y., Bai, G.L. and Yin, Y.G. (2018), "Experiment study on bond slip behavior between section steel and RAC in SRRC structures", Constr. Build. Mater., 175, 104-114. https://doi.org/10.1016/j.conbuildmat.2018.04.120.
  22. Lu, Y.Y., Li, N., Li, S. and Liang, H.J. (2015), "Behavior of steel fiber reinforced concrete-filled steel tube columns under axial compression", Constr. Build. Mater., 95, 74-85. https://doi.org/10.1016/j.conbuildmat.2015.07.114.
  23. McMahon, J.A. and Birely, A.C. (2018), "Service performance of steel fiber reinforced concrete (SFRC) slabs", Eng. Struct., 168, 58-68. https://doi.org/10.1016/j.engstruct.2018.04.067.
  24. Nzabonimpa, J.D. and Hong, W.K. (2018), "Novel precast erection method of interlocking mechanical joints using couplers", J. Constr. Eng., 144, 04018036. https://doi.org/10.1061/(ASCE)CO.1943-7862.0001482.
  25. Paultre, P., Eid, R., Langlois, Y. and Levesque, Y. (2010), "Behavior of steel fiber-reinforced high-strength concrete columns under uniaxial compression", J. Struct. Eng., 136(10), 1225-1235. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000211.
  26. Qureshi, L.A. and Muhammad, U. (2018), "Effects of incorporating steel and glass fibers on shear behavior of concrete column-beam joints", KSCE J. Civil Eng., 22(8), 2970-2981. https://doi.org/10.1007/s12205-017-0037-8.
  27. Savino, V., Lanzoni, L., Tarantino, A.M. and Viviani, M. (2018), "Tensile constitutive behavior of high and ultra-high performance fibre-reinforced-concretes", Constr. Build. Mater., 186, 525-536. https://doi.org/10.1016/j.conbuildmat.2018.07.099.
  28. Seo, J. and Varma, A.H. (2017), "Experimental behavior and design of steel plate composite-to-reinforced concrete lap splice connections", J. Struct. Eng., 143, 04017011. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001711.
  29. Shakya, K., Watanabe, K., Matsumoto, K. and Niwa, J. (2012), "Application of steel fibers in beam-column joints of rigidframed railway bridges to reduce longitudinal and shear rebars", Constr. Build. Mater., 27(1), 482-489. https://doi.org/10.1016/j.conbuildmat.2011.07.016.
  30. Shi, X.M., Xie, N., Fortune, K. and Gong, J. (2012), "Durability of steel reinforced concrete in chloride environments: An overview", Constr. Build. Mater., 30, 125-138. https://doi.org/10.1016/j.conbuildmat.2011.12.038.
  31. Sukontasukkul, P., Jamnam, S., Sappakittipakorn, M., Fujikake, K. and Chindaprasirt, P. (2018), "Residual flexural behavior of fiber reinforced concrete after heating", Mater. Struct., 51(4), 4. https://doi.org/10.1617/s11527-018-1210-3.
  32. Tong, L.W., Liu, B. and Zhao, X.L. (2017), "Numerical study of fatigue behaviour of steel reinforced concrete (SRC) beams", Eng. Fract. Mech., 78, 477-496. https://doi.org/10.1016/j.engfracmech.2017.02.017.
  33. Tong, L.W., Liu, B., Xian, Q.J. and Zhao, X.L. (2016), "Experimental study on fatigue behavior of Steel Reinforced Concrete (SRC) beams", Eng. Struct., 123, 247-262. https://doi.org/10.1016/j.engstruct.2016.05.052.
  34. Tong, L.W., Xiao, S., He, L., Zhang, Y.F. and Zhao, X.L. (2018), "Fatigue behavior of steel reinforced concrete (SRC) beams with different shear span-to-depth ratios", Eng. Struct., 166, 339-353. https://doi.org/10.1016/j.engstruct.2018.03.071.
  35. Tsai, M.H., Zhang, J.F., Song, Y.P. and Lu, J.K. (2018), "Dynamic performance of a composite building structure under seismic ground motions", Earthq. Struct., 15(2), 179-191. https://doi.org/10.12989/eas.2018.15.2.179.
  36. Valipour, H., Vessali, N. and Foster, S. (2016), "Fibre-reinforced concrete beam assemblages subject to column loss", Mag. Concrete Res., 68(6), 305-317. https://doi.org/10.1680/jmacr.15.00095.
  37. Wu, K., Chen, F., Chen, C.Y., Zheng, H.M. and Xu. J. N. (2019), "Load-transfer mechanism and bond-stress components in steel and steel fiber-reinforced concrete structure", J. Struct. Eng., 145(12), 04019160. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002441.
  38. Wu, Y.T., Kang, D.Y., Gao, L., Su, Y.T. and Yang, Y.B. (2018), "Seismic behavior of bolted endplate connection between steel reinforced concrete (SRC) wall and SRC beam for use in highrise buildings", Int. J. Civil Eng., 16(11A), 1561-1572. https://doi.org/10.1007/s40999-018-0296-x.
  39. Yang, Y., Yu, Y.L. and Guo, Y.X. (2016), "Experimental study on shear performance of partially precast Castellated Steel Reinforced Concrete (CPSRC) beams", Steel Compos. Struct., 21, 289-302. https://doi.org/10.12989/scs.2016.21.2.289.
  40. Ying, W.D. and Chen, Z.P. (2016), "Interface bond force transfer mechanisms and its influence analysis between shape steel and high-strength concrete", China Civil Eng. J., 9, 53-63. (in Chinese)
  41. Yoo, D.Y. and Moon, D.Y. (2018), "Cyclic tensile behavior of SFRC: Effect of steel fibers on the flexural behavior of RC beams with very low reinforcement ratios", Constr. Build. Mater., 188, 237-254. https://doi.org/10.1016/j.conbuildmat.2018.08.099.
  42. Yoo, D.Y., Yuan, T.F., Yang, J.M. and Yoon, Y.S. (2017), "Feasibility of replacing minimum shear reinforcement with steel fibers for sustainable high-strength concrete beams", Eng. Struct., 147, 207-222. https://doi.org/10.1016/j.engstruct.2017.06.004.
  43. Yuan, C., Chen, W.S., Pham, T.M. and Hao, H. (2018), "Bond behavior between basalt fibres reinforced polymer sheets and steel fibres reinforced concrete", Eng. Struct., 176, 812-824. https://doi.org/10.1016/j.engstruct.2018.09.052.
  44. Zhang, Y.Y. and Dias-Da-Costa, D. (2017), "Seismic vulnerability of multi-span continuous girder bridges with steel fibre reinforced concrete columns", Eng. Struct., 150, 451-464. https://doi.org/10.1016/j.engstruct.2017.07.053.
  45. Zheng, H.H, Chen, Z.P. and Su Y.S. (2016), "Bond behavior of Hshaped steel embedded in recycled aggregate concrete under push-out loads", Int. J. Steel Struct., 16(2), 347-360. https://doi.org/10.1007/s13296-016-6008-y.