• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1676-1681
• /
• 2004

The main reason for applying positive pressure variable clearance packing in fossil power plant is high efficiency and energy saving movement in the government. This study intends to analyze the turbine efficiency through the shaft packing improvement in thermal power plant and makes its comparison to that of the each packing type

• 설비공학논문집
• /
• 제14권10호
• /
• pp.775-780
• /
• 2002

An experimental study on the characteristics of several kinds of packing materials was carried out in order to get the optimum design data for the packed-type rectification system of an NH$_3$/$H_2O$ GAX absorption heat pump. Several suitable packing materials were examined and the bulk of steel wire was shown as the most effective packing material in rectifier. The optimum volumetric ratio of packed steel wire in rectifier was obtained as around 36%. The performance results can be adapted in rectifier design of absorption heat pump.

• 설비공학논문집
• /
• 제18권7호
• /
• pp.571-577
• /
• 2006

The characteristics of ice packing factor (IPF) at the ice slurry system using one line type are compared with the system using two lines type. The installation space for one transporting line is saved at the one line system. For the one line type, the ice packing factor is reduced along the downstream, but for the two lines type, the ice packing factor is fixed. For the one line system, mass flow rate in the main line is fixed along the down-stream, but for two lines system, the mass flow rate in the main line is reduced along the downstream. For one line system, along the down stream after IPF=0, the temperature at the main steam is increased, and the extracted mass flow is increased. The initial IPF, at which the IPF is not arrived at zero upto the final node, is proposed for the B area.

• 한국가스학회지
• /
• 제18권4호
• /
• pp.51-55
• /
• 2014

본 연구에서는 한곳에서 접촉하는 오링과 여러 곳에서 접촉하는 멀티접촉패킹에 대한 밀봉특성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, LP가스압력 1.8MPa을 공급하였을 때 기존의 오링에서는 밀봉성에 관련된 2.5MPa의 수직접촉 최대응력을 발생하였다. 반면에 새롭게 고안된 멀티접촉패킹에서는 3.01MPa이 발생하여 20.4%나 높아진 밀봉성이 향상되었음을 알 수 있다. 또한, 밀봉내구 안전성에 밀접한 관련이 있는 압출현상은 기존 오링의 경우 1.62MPa의 가스압력에서 발생되었지만, 멀티접촉패킹에서는 1.8MPa 정도로 가스내압을 올려도 압출현상이 발생되지 않는 것은 오랫동안 밀봉작용을 한다는 것을 의미한다. 따라서 밀봉성과 내구안전성을 높게 요구할 때는 한곳에서 접촉하는 기존의 오링보다는 여러 곳에서 접촉하는 멀티접촉패킹을 사용하는 것이 유리함을 알 수 있다.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.370-376
• /
• 2011

Recently, the application range of plastic gears is widely expanding by the development of engineering plastics with good mechanical properties. Plastic gears have excellent performances such as light weight, water resistance and vibration absorbing ability for metallic gears. In this study, the optimization of injection molding process was done for the large disk type plastic gears of auto phoropter. Design Of Experiment (Taguchi method) was adopted to find a tendency of molding conditions that influence the flatness of disk type gear. Four main factors for molding conditions were selected based on injection temperature, filling time, packing pressure and mold temperature. Also, Filling, packing and cooling analyses were carried out to evaluate Z directional deflection of large disk type gear by using the simulation software (Moldflow) based on the DOE. From the results, it was found that the injection temperature and packing pressure are the most sensitive parameters for the Z directional deflection of large disk type gears.

• 한국식생활문화학회지
• /
• 제29권1호
• /
• pp.1-8
• /
• 2014

This study was carried out to investigate the consumption behaviors of environmentally-friendly agricultural products, including satisfaction of purchases. Questionnaires completed consumers were statistically analyzed. Regarding purchase frequencies of environmentally-friendly agricultural and animal products, consumers consumed them 1 time per month. No significant differences in consumption by age, living area, family type, or BMI were found. Exactly 38.2% of consumers preferred to purchase items in the packing amount of 0.2-0.5 kg, whereas 39.7% of consumers preferred amounts from 0.5-1.0 kg. Significant differences in packing amount were found according to age (p<0.05) and family type (p<0.01). However, there were no significant differences according to living area or BMI group. Many consumers made decisions based on the outer packing label (69.6%). Significant differences by age and living area were not found, whereas there was significant difference according to family type (p<0.05). Consumers answered that they purchased products in a general supermarket (24.7%) and cooperative (24.2%). Significant differences were found by age and living area (p<0.01) but not by family type. Consumer satisfaction of purchases scored 3.39 out of 5 points. In conclusion, significant differences in consumer satisfaction were not found according to age, living area, family type, or BMI.

• 한국대기환경학회지
• /
• 제17권1호
• /
• pp.51-56
• /
• 2001

This study was carried out to interpret mathematically hydraulic behaviour in packing tower which packed 50 mm plastic Hiflow-ring with a dimension of 300 mm wide and 1,400 mm high. In view of energy saving, the recent packing. 50 mm plastic Higlow-ring was superior to conventional packings because of low pressure drop in high loads. As relative error between numerically predicted and experimentally obtained values was less then 6% in the loading and flooding point, it found that therir results appeared to be adequate. Comparison of hose two values in both dry and wet packing conditions. relative errors amount to 3.96 and 5.6%, respectively. In order to evaluate the operating characteristics of packing, the type, size, and material for packings must be estimated in various system and loads. This study is able to calculated pressure drop, hold-up, gas and liquid loads using mathematical interpretation. For these calculation, the specific constants of each packings must be calculated first all. The method of mathematical interpretation in this study turned out to be superior to the existing methods because of reduced errors at loading and flooding point.

• 동력기계공학회지
• /
• 제9권2호
• /
• pp.93-98
• /
• 2005

The performance of cooling tower is dependent on the thermal performance of the packings. It's assessed by heat transfer rate and fan power. In this study, new packing was developed for application in compact type cross-flow cooling tower. The packing characteristic curve and the pressure drop curve were obtained by measuring packing characteristic values and pressure drops of small sized filler in comparison to existing mid-large sized filler. The heat transfer characteristics on small sized filler are about 66% higher than existing mid-large sized filler. The pressure drop characteristics on small sized filler are about two times of the pressure drop characteristics on existing mid-large sized filler.

• 한국안전학회지
• /
• 제14권3호
• /
• pp.101-109
• /
• 1999

This study attempts to analyse the solid mixing in the feeder and the packing effect for pressure fluctuations in the fluidized bed. To study the mixing characteristics of solid in vibrating feeder for the stable operations of fluidized combustion, the system consisted of two groups of particles such that fine particles were located on the top of the coarse particles before vibratory mixing had started. The effects of packing materials on the pressure fluctuations in a fluidized bed were analysed by using a statistical method to interpret the behavior of fluidized bed. The experiments were carried out in a fluidized bed of 6.7cm-ID, and the experimental variables were particle sizes, of 115 to 1,015$\mu\textrm{m}$ in diameter and the multi-sized particles haying Rosin-Rammler and Gaussian distributions. The settled bed heights of particles to diameter ratios (L/D) were ranged from 0.5 to 2.0. And fluidizing of particles was carried out by air. The packing materials used were screen packing, and the properties of the pressure fluctuations in the fluidized bed were measured by a differential pressure transducer. The properties of the pressure fluctuations calculated were the mean, the standard deviation, and the major frequency of the power spectral density functions. From the characteristics of fluidizing, it was found that the standard deviation of pressure fluctuations could be effectively used to explain the fluidized phenomena, and the packing materials affected severely the properties of the pressure fluctuations. As a result, from the interpretation by spectral analysis, the effects of measuring radius of pressure fluctuations on standard deviation were constant in the case of the fluidized bed with and without packing materials. However, the effects of measuring the height of pressure fluctuations on standard deviations were linear increasing for the fluidized bed with packing materials, but were constant for the fluidized bed without packing materials at 4.5cm above the gas distributor. The major frequency of pressure fluctuations was found to be nearly independent of fluidized system. Also, the major frequency of pressure fluctuations decreased with increasing packing size, and it had maximum value at 10% of the packing amount.

• 한국시뮬레이션학회논문지
• /
• 제11권2호
• /
• pp.67-75
• /
• 2002

This paper proposes a parallel simulation algorithm for bounded Petri nets in a single processor, which exploits the SIMD(Single Instruction Multiple Data)-type parallelism. The proposed algorithm is based on a data packing scheme which packs multiple bytes data in a single register, thereby being manipulated simultaneously. The parallelism can reduce simulation time of bounded Petri nets in a single processor environment. The effectiveness of the algorithm is demonstrated by presenting speed-up of simulation time for two bounded Petri nets.