• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.133-142
• /
• 2005

The research concentrates on improving the in-hole seismic probe, which has been developed in past five years, to be used in stiffness measurements of tunnel-face materials. The size of probe was reduced to be fit in 45-mm diameter holes (or BX) drilled by a jumbo-drill, which is used to drill holes to install explosives for tunneling. Also trigger system was improved by using a down-speeding motor for operating convenience and air packing system was replaced with a set of plate-springs to eliminate supply of compressed air. These modifications are to adjust the probe for the unfavourable environment inside of tunnels and to test without any further drilling cost. The probe and testing procedure were successfully adopted with horizontal holes drilled by a jumbo-drill at a tunnel-face to evaluate the stiffness of rock mass. The measured shear wave velocities can be used to estimate deformation properties of rock mass for tunnel analyses.

• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.55-67
• /
• 2000

In this paper, an experimental study of the rheological behavior of granular flow in a new type of storage silo is presented. The main characteristic of the new design is a hexagonal shape chosen with the objective of minimizing the stresses applied to the stored grains, and to reduce grain damage during the filling and emptying processes. Measurements of stress distribution and flow patterns are shown for a variety of granular materials. Because of the design of the silo, the granular material adopts its natural rest angle at all times eliminating collisional stresses and impacts between grains. A homogeneous, low friction flow is naturally achieved which provides a controlled stress distribution throughout the silo during filling and emptying. Secondary dynamic stresses, which are responsible for wall failure in conventional silos of the vertical type, are completely eliminated. A comparison between the two geometries is presented with data obtained for these silos and a number of granular materials. The discharge pattern inhibits powder formation in the silo and the filling system virtually eliminates unwanted material packing. Finally, notwithstanding the rheological advantages of this new design, the hexagonal cells that constitute the silo have many other advantages, such as the possible use of solar energy to control the humidity inside them. The cell type design allows for versatile storage capabilities and the elevation above the ground provides unlimited transportation facilities during emptying.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.63 no.4
• /
• pp.338-359
• /
• 2018

Soybean (Glycine max L.), a major part of Asian diet, is consumed primarily for its nutritional value. However, poor storage stability often leads to loss of nutritional value or deterioration in quality. This study focused on the storage stability of soy flour obtained from raw and roasted "Saedanbaek" soybeans packed in polyethylene (PE) and polypropylene (PPE) film bags that were stored at $4^{\circ}C$, $20^{\circ}C$ and $45^{\circ}C$ for 48 weeks. The early acid values (diene and p-anisidine) of raw soybean flour (RSF) at high temperature (HT) were higher than those at refrigerated temperature (RFT) and room temperature (RT) during 48 and 12 to 36 weeks, respectively. In the case of roasted soybean flour (ROSF), which was stored at RFT and RT, the acid and conjugated diene values gradually increased after 24 weeks. In RSF, the peroxide value increased since the beginning of the $24^{th}$ week. The p-anisidine value also increased during 12 to 36 weeks but was much lower than the values obtained from HT storage. As the peroxide values decreased, the p-anisidine values increased, indicating an inverse relationship. Lipoxygenase activity of ROSF at all storage conditions was lower than RSF. Several differences were observed between the packing materials used. This study could, therefore, provide useful information for the industrial use of soybean flour (SF).

• Korean Journal of Materials Research
• /
• v.29 no.8
• /
• pp.469-476
• /
• 2019

A lead-free bulk ceramic having a chemical formula $Ba_{0.8}Ca_{0.2}(Ti_{0.8}Zr_{0.1}Ce_{0.1})O_3$ (further termed as BCTZCO) is synthesized using mixed oxide route. The structural, dielectric, impedance, and conductivity properties, as well as the modulus of the synthesized sample are discussed in the present work. Analysis of X-ray diffraction data obtained at room temperature reveals the existence of some impurity phases. The natural surface morphology shows close packing of grains with few voids. Attempts have been made to study the (a) effect of microstructures containing grains, grain boundaries, and electrodes on impedance and capacitive characteristics, (b) relationship between properties and crystal structure, and (c) nature of the relaxation mechanism of the prepared samples. The relationship between the structure and physical properties is established. The frequency and temperature dependence of the dielectric properties reveal that this complex system has a high dielectric constant and low tangent loss. An analysis of impedance and related parameters illuminates the contributions of grains. The activation energy is determined for only the high temperature region in the temperature dependent AC conductivity graph. Deviation from the Debye behavior is seen in the Nyquist plot at different temperatures. The relaxation mechanism and the electrical transport properties in the sample are investigated with the help of various spectroscopic (i.e., dielectric, modulus, and impedance) techniques. This lead free sample will serve as a base for device engineering.

• Membrane Journal
• /
• v.30 no.6
• /
• pp.450-459
• /
• 2020

Membrane-based separations have the potential to reduce energy consumption and environmental impact associated with conventional processes. However, many researches have been done to develop new membrane materials with greater selectivity and permeability. Here, we report highly selective membranes by introducing bulky ethyl substituents into the polyimide. The ethyl group in the ortho position to the imide nitrogen interferes the chain packing and increases chain stiffness and the distance between the polymer chains. The polyimide membranes were synthesized from various aromatic dianhydrides and 4,4'-methylenebis(2,6-diethylaniline) (MDEA). The synthesized membranes with increased gas diffusion length due to bulky substituents showed improved propylene/propane (C3H6/C3H8) selectivity. Single gas permeation showed high C3H6/C3H8 selectivity of 14.5, and C3H6 permeability of 7.0 barrer was found in MDEA-polyimide. Mixed-gas permeation results also demonstrate that MDEA-polyimide can achieve high selectivity in mixed-gas environment. Furthermore, this approach could significantly increase the feasibility of economic propylene separation compared to conventional polymer materials.

• Composites Research
• /
• v.34 no.1
• /
• pp.70-75
• /
• 2021

This paper presents a novel algorithm to reconstruct meso-scale representative volume elements (RVE), referring to experimentally observed features of Sheet Molding Compound (SMC) composites. Predicting anisotropic mechanical properties of SMC composites is challenging in the multiscale virtual test using finite element (FE) models. To this end, an SMC RVE modeler consisting of a series of image processing techniques, the novel reconstruction algorithm, and a FE mesh generator for the SMC composites are developed. First, micro-CT image processing is conducted to estimate probabilistic distributions of two critical features, such as fiber chip orientation and distribution that are highly related to mechanical performance. Second, a reconstruction algorithm for 3D fiber chip packing is developed in consideration of the overlapping effect between fiber chips. Third, the macro-scale behavior of the SMC is predicted by the multiscale analysis.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.8
• /
• pp.181-185
• /
• 2021

Road fine dust is not simply a problem of air pollution, but is threatening the health and life of the public, including pedestrians using sidewalks. There are various policy proposals related to road fine dust reduction, but the actual effect cannot be guaranteed. Therefore, in order to ensure the safe and pleasant passage of the people, the pavement pavement (sidewalk pavement) for fine dust management on the road should be designed by considering the location, use, function, etc., and appropriate paving materials and construction methods should be selected and designed or sidewalk facilities should be prepared. Therefore, this study examines the concept and legal basis of sidewalk pavement, reviews the status of sidewalk pavement-related technologies that purify air pollution, and utilizes sidewalk pavement materials under the revised sidewalk pavement guidelines for reducing fine dust, 「Act on Promotion of Purchasing of Green Products」 We intend to establish a legal basis for early application of sidewalk pavement technology by proposing measures and amendments to local government sidewalk pavement management rules.

• Journal of the Society of Disaster Information
• /
• v.14 no.1
• /
• pp.89-100
• /
• 2018

when the explosive wastes to be treated as designated wastes are brought into the wastes treatment plant by mistake and lead to an explosion in the wastes disposal process, many people and property damage are involved. Waste should be treated properly. As mentioned in this paper, ignition reac- tion tests of ignitable re-burning of explosives packing material waste (solid butadiene) confirmed that ignition was easily occurred, and that even small ignition sources were easily ignited and burned quickly and explosively. In particular, when explosives are loaded into incineration wastes in large quantities and mixed with organic compound wastes, such as fire and explosion accidents caused by explosives packing materials at waste disposal sites, flammable and oxidative gases are generated due to mutual oxidation and pyrolysis It is confirmed that there is a possibility that ignition sources such as spark ignite and instantaneously lead to explosion. It is hoped that this study will be a small reference for on - site detection in the field of fire, and it is expected that the fire - fighting agency will be recognized as a fire investigation agency and will contribute to the improvement of the credibility.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.990-995
• /
• 1999

To determine the effect of chemical structure of linear amine curing agents on thermal and mechanical properties, standard epoxy resin DGEBA was cured with ethylene diamine(EDA) and hexamethylene diamine(HMDA) in a stoichiometrically equivalent ratio. From this work, the effect of linear amine curing agents on the thermal and mechanical properties is significantly influenced by the chemical structure or chain length of curing agents. In contrast, the results show that the DGEBA/EDA system having the two carbons had higher values in the thermal stability, maximum conversion of epoxide, density, glass transition temperature, tensile modulus, flexural strength, and flexural modulus than the DGEBA/HMDA system having the six carbons, whereas the DGEBA/EDA cure system had relatively low values in the shrinkage(%), thermal expansion coefficient, tensile strength, and had similar values in the maximum exothermic temperature, and conversion of epoxide compared to the DGEBA/HMDA cure system. This findings indicate that packing ability in the HMDA structure affects the thermal and mechanical properties.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.648-653
• /
• 2006

As an alternative for the traditional materials packed in biofilters treating gaseous VOCs, a novel packing material has been developed and tested. In the packing material(named as Hydrogel Bead, HB), pollutant-degrading microorganisms were immobilized in hydrogel consisted of alginate, polyvinyl alcohol(PVA), and powdered activated carbon. A closed-bottle study showed that the HB rapidly removed gaseous styrene without the losses of adsorption and biodegradation capacity. Biofilter column experiments using the HBs also demonstrated that greater than 95% of removal efficiencies were found at an inlet styrene loading rate of $245g/m^3/hr$, which was higher biofilter performance than other elimination capacity reported earlier. Furthermore, when the inlet styrene concentration increased stepwise, the adsorption played an important role in overall styrene removals. The absorbed styrene was found to be biodegraded in the following low inlet loading condition. Consequently, the new HB material is able to successfully minimize the drawbacks of activated carbon(necessity of regeneration) and biological processes(low removal capacity at dynamic loading conditions), and maximize the overall performance of biofilter systems treating VOCs.