• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.116-120
• /
• 2011

In this paper, we studied the optimization of the screen pringting method for crystalline silicon solar cell fabrication. The 156 * 156 mm2 p-type silicon wafers with $200{\mu}m$ thickness and $0.5-3{\Omega}cm$ resistivity were used after texturing, doping, and passivation. Screen printing method is a common way to make the c-Si solar cell with low-cost and high-efficiency. We studied the optimized condition for screen printing with crystalline silicon solar cell as changing the printing direction (finger line or bus bar), finger width, and mesh angle. As a result, the screen printing with finger line direction showed higher finger height and better conversion efficiency, compared with one with bus bar direction. The experiments with various finger widths and mesh angles were also carried out. The characteristics of solar cells was obtained by measuring light current-voltage, optical microscope and electroluminescence.

• Korean Journal of Materials Research
• /
• v.16 no.6
• /
• pp.351-354
• /
• 2006

[ $Co_{1-x}Fe_xSb_3$ ] skutterudites were synthesized by encapsulated induction melting and their thermoelectric properties were investigated. Single phase ${\delta}-CoSb_3$ was successfully obtained by the subsequent heat treatment at 773 K for 24 hours in vacuum. However, ${\delta}-CoSb_3$ was decomposed to FeSb2 and Sb when $x{\leq}0.3$, which means that the solubility limit of Fe to Co is x<0.3. The positive signs of Seebeck coefficients for all Fe-doped specimens revealed that Fe atoms acted as p-type dopants by substituting Co atoms. Thermoelectric properties were remarkably enhanced by Fe doping and optimum composition was found to be $Co_{0.7}Fe_{0.3}Sb_3$ in this study.

• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.274-277
• /
• 2016

Effects of interlayer insertion between multi-quantum well and electron blocking layer of green light emitting diode on diode performances were studied by device simulation. Dependence of Mg doping depth on characteristics of current-voltage, emitting wavelength, leakage current, and external quantum efficiency was investigated, and the optimum diode structure was presented. Device structures with interlayers doped in entire region and up to 30 nm showed remarkable reduced leakage current and effectively relieved efficiency droop which is one of the biggest challenges in green light emitting diode. Furthermore, the most improved characteristics in current-voltage and electroluminescence was obtained by the latter structure.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.632-637
• /
• 2000

Thermoelectric conversion properties of commercial Fe-Si2 and Fe-Si alloy ingots prepared by RF inductive furnace were investigated. As sintering temperature increased, density of the specimen increased and the phase transformation from metallic phases ($\varepsilon$-FeSi, ${\alpha}$-Fe2Si5) to semiconducting phase (${\beta}$-FeSi2) occurred more effectively. The FeSi phase was detected even after 100hrs of annealing treatment. For the Fesi1.95∼FeSi2.05 specimens prepared by RF inductive furnace, the thermoelectric property improved as the composition of the specimen approached to stoichiometric composition FeSi2. Electrical conductivity of the specimen increased with increasing temperatures showing typical semiconducting behavior. From the electrical conductivity measurements, activation energy in the intrinsic region (above about 700 K) was calculated to be approximately 0.46 eV. In spite of non-doping, the Seebeck coefficient for every specimen exhibited p-type conduction due to Si deficiency. Its maximum value was located at about 475 K, and then decreased abruptly with increasing temperatures. The power factor was governed by the Seebeck coefficient of the specimen more significantly than by electrical conductivity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.213-216
• /
• 2003

Recently a new high power device GCT (Gate Commutated Turn-off) thyristor has been successfully introduced to high power converting application areas. GCT thyristor has a quite different turn-off mechanism to the GTO thyristor. All main current during turn-off operation is commutated to the gate. Therefore, IGCT thyristor has many superior characteristics compared with GTO thyristor; especially, snubberless tum-off capacibility and higher turn-on capacibility. The basic structure of the GeT thyristor is same as that of the GTO thyristor. This makes the blocking voltage higher and controllable on-state current higher. The turn-off characteristic of the GCT thyristor is influenced by the minority carrier lifetime and the performance of the gate drive unit. In this paper, we present turn-off characteristics of the 2.5kV PT(Punch-Through) type GCT as a function of the minority carrier lifetime and variation of the doping profile shape of p-base region.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.331-336
• /
• 2005

The influence of water molecule on the electrical properties of single-walled carbon nanotube field effect transistors (SWNT-FETs) was reported. Conductance suppression was observed with the increase of the humidity. This can be explained by doping of the SWNT-FETs, which has p-type semiconductor characteristic, with the water molecules acting as an electron donor. However, after 65 % of humidity, conductance of the SWNT-FETs started to increase again, due to the opening of electron channels. Upon annealing at $400^{\circ}C$ in Ar atmosphere, conductance increases more than 500 %, and the threshold voltage shifts toward further positive gate voltages. The results of this experiment support possible application of single-walled carbon nanotubes for humidity sensing material.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.5
• /
• pp.418-422
• /
• 1989

Cadmium-doped indium sesquioxide systems with a variety of CdO mol % were prepared to investigate the effect of doping on the electrical properties of indium sesquioxide. The electrical conductivities of pure $In_2O_3$ and Cd-doped $In_2O_3$ systems were measured in the temperature range from 25 to $1200^{\circ}C$ and $P_O_2$ range from $10^{-7}$ to $10^{-1}$ atm, and the thermoelectric power was measured in the same temperature range. The electrical conductivity and thermopower decreased with increasing CdO mol % indicating that all the samples are n-type semiconductors. The electrical conductivities of pure $In_2O_3$ and lightly doped $In_2O_3$ were considerably affected by the chemisorption $O_2$ at temperatures of 400 to $560^{\circ}C$ and then gaseous oxygen was reversibly chemisorbed at the temperature. The predominant defects in $In_2O_3$ are believed to be triply-charged interstitial indiums at temperatures above $560^{\circ}C$ and oxygen vacancies below $560^{\circ}C$. In Cd-doped $In_2O_3$ systems, cadmium acts as an electron acceptor and inhibits the transfer of lattice indium to interstitial sites, which give rise to the decrease of the electrical conductivity.

• Korean Journal of Materials Research
• /
• v.31 no.8
• /
• pp.445-449
• /
• 2021

Zintl compound Mg₃Sb₂ is a promising candidate for efficient thermoelectric material due to its small band gap energy and characteristic electron-crystal phonon-glass behavior. Furthermore, this compound enables fine tuning of carrier concentration via chemical doping for optimizing thermoelectric performance. In this study, nominal compositions of Mg_3.8Sb_2-xTe_x (0 ≤ x ≤ 0.03) are synthesized through controlled melting and subsequent vacuum hot pressing method. X-ray diffraction (XRD) and scanning electron microscopy (SEM) are carried out to investigate phase development and surface morphology during the process. It should be noted that 16 at. % of excessive Mg must be added to the system to compensate for the loss of Mg during melting process. Herein, thermoelectric properties such as Seebeck coefficient, electrical conductivity, and thermal conductivity are evaluated from low to high temperature regimes. The results show that Te substitution at Sb sites effectively tunes the majority carriers from holes to electrons, resulting in a transition from p to n-type. At 873 K, a peak ZT value of 0.27 is found for the specimen Mg_3.8Sb_1.99Te_0.01, indicating an improved ZT value over the intrinsic value.

• Mass Spectrometry Letters
• /
• v.12 no.2
• /
• pp.47-52
• /
• 2021

Evaluating the impurity concentrations in semiconductor thin films using time of flight secondary ion mass spectrometry (ToF-SIMS) is an effective technique. The mass interference between isotopes and matrix element in data interpretation makes the process complex. In this study, we have investigated the doping concentration of phosphorus in, phosphorus doped silicon thin film on glass using ToF-SIMS in the dynamic mode of operation. To overcome the mass interference between phosphorus and silicon isotopes, the quantitative analysis of counts to concentration conversion was done following two routes, standard relative sensitivity factor (RSF) and SIMetric software estimation. Phosphorus doped silicon thin film of 180 nm was grown on glass substrate using hot wire chemical vapor deposition technique for possible applications in optoelectronic devices. Using ToF-SIMS, the phosphorus-31 isotopes were detected in the range of 10¹~10⁴ counts. The silicon isotopes matrix element was measured from p-type silicon wafer from a separate measurement to avoid mass interference. For the both procedures, the phosphorus concentration versus depth profiles were plotted which agree with a percent difference of about 3% at 100 nm depth. The concentration of phosphorus in silicon was determined in the range of 10¹⁹~10²¹ atoms/cm³. The technique will be useful for estimating distributions of various dopants in the silicon thin film grown on glass using ToF-SIMS overcoming the mass interference between isotopes.

• Korean Journal of Materials Research
• /
• v.7 no.10
• /
• pp.856-862
• /
• 1997

박막형 CdTe/CdS 태양전지의 배면전극(back contacts)물질로서 Cu도핑된 ZnTe 박막(ZnTe:Cu)을 전착법(electroplating)으로 제조하는 연구를 수행하였다. Sulfate계의 전해질 수용액에서 CdTe 기판과 투명전극으로 코팅된 유리(In$_{2}$O$_{3}$: Sn, ITO)기판 위에 ZnTe 박막을 코팅하는 방법으로써 potentiostat와 기판(cathode), Pt counter electrode, Ag/AgCI 표준전극으로 구성된 장치를 사용하여 pH=2.5-4, T=70-8$0^{\circ}C$, 0.02M $Zn^{2+}$ 1x$10^{-4}$M TeO$_{2}$, 0.2M $K_{2}$SO$_{4}$조건에서 -0.800 Vs~-0.975 V 범위의 전압(V$_{a}$ )에 걸쳐 실험하였다. ITO박막을 기판으로 사용하여 cyclic voltammogram을 작성한 결과 약 -0.50 V 에서 Te환원 peak이 나타났다. Auger electron spectroscopy (AES)로 조성분석한 결과 표면에서 Zn signal이 강하게 나왔고 시편의 두께에 따라 Zn의 signal감소하는 반면 Cd signal은 증가하는 것이 확인되었다. SEM 사진으로부터 ZnTe의 표면이 작은 입자 (0.2$\mu\textrm{m}$ 이하)로 구성되어 있으며 낮은 V$_{a}$ 에서는 입자가 작아지면서 조직이 치밀해짐이 관찰되었다. Optical transmission방법에 의하여 ITO기판위에 입혀진 박막의 밴드갭은 2.5 eV으로 측정되었다. 수용액중의 Cu$_{2+}$와 triethanolamine(TEA)은 산성용액에서 착물형성이 이루어지지 않았으며 1,10-phenanthroline과는 pH=2에서도 착물이 형성되었다.