• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2263-2273
• /
• 2000

Catalytic wet air oxidation of acetic acid over Mn-Ce based catalysts deposited on various supports ($SiO_2$, $TiO_2$, $ZrO_2$), $ZrSiO_4$, $ZrO_2(10wt%)/TiO_2$) have been carried out in high pressure microreactors. Also, promotional effects by small addition(O.5~1.0 wt%) of p-type semiconductors (CoO, $Ag_2O$, SnO) have been investigated. From the screening tests for initial activity ranking, both Mn(2.8)-Ce(7.2 wt%) and Ru(O.4)Mn(2.7)-Ce(6.9 wt%) supported on $TiO_2$ were selected as the promising reference candidates. In $Mn-Ce/TiO_2$ reference catalyst, addition of small amount of each p-type semiconductor (Co, Sn and Ag) resulted in activity promotional effect and the degree of the increase was in the following order: Co> Ag > Sn. Especially, $Mn-Ce/TiO_2$ promoted with 0.5 wt% Co gave the 2.6 folds activity increase compared to the reference case attributing to the surface area increase as well as synergy effect. In $Ru-Mn-Ce/TiO_2$ reference catalyst, only Co(1.0 wt%) promoted case showed a little reaction rate increase.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.6
• /
• pp.275-281
• /
• 2017

AlN is a promising material for wide band gap and high-frequency electronics device due to its wide bandgap and high thermal conductivity. AlN has advantages as materials for power semiconductors with a larger breakdown field, and a smaller specific on-resistance at high voltage. The growth of a p-type AlN epilayer with high conductivity is important for a manufacturing an AlN-based applications. In this paper, Mg doped AlN epilayers were grown by a mixed-source HVPE. Al and Mg mixture were used as source materials for the growth of Mg-doped AlN epilayers. Mg concentration in the AlN was controlled by modulating the quantity of Mg source in the mixed-source. Surface morphology and crystalline structure of AlN epilayers with different Mg concentrations were characterized by FE-SEM and HR-XRD. XPS spectra of the Mg-doped AlN epilayers demonstrated that Mg was doped successfully into the AlN epilayer by the mixed-source HVPE.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.14-18
• /
• 2019

The conductivity of a semiconductor is primarily determined by the carriers. To achieve higher conductivity, the number of carriers should be high, and an energy trap level is created so that the carriers can cross the forbidden zone with low energy. Carriers have a crystalline binding structure, and interfacial mismatching tends to make them less conductive. In general, high-concentration doping is typically used to increase mobility. However, higher conductivity is also observed in non-orthogonal conjugation structures. In this study, the phenomena of higher conductivity and higher mobility were observed with space charge limiting current due to tunneling phenomena, which are different from trapping phenomena. In an atypical structure, the number of carriers is low, the resistance is high, and the on/off characteristics of capacitances are improved, thus increasing the mobility. ZTO thin film improved the on/off characteristics of capacitances after heat treating at $150^{\circ}C$. In charging and discharging tests, there was a time difference in the charge and discharging shapes, there was no distinction between n and p type, and the bonding structure was amorphous, such as in the depletion layer. The amorphous bonding structure can be seen as a potential barrier, which is also a source of space charge limiting current and causes conduction as a result of tunneling. Thus, increased mobility was observed in the non-structured configuration, and the conductivity increased despite the reduction of carriers.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.19-24
• /
• 2007

With recent advancement of high-speed, multi-gigabit data transmission capabilities, serial links have been more widely adopted in industry than parallel links. Since the parallel link design forces its transmitter to transmit both the data and the clock to the receiver at the same time, it leads to hardware's intricacy during high-speed data transmission, large power consumption, and high cost. Meanwhile, the serial links allows the transmitter to transmit data only with no synchronized clock information. For the purpose, clock and data recovery circuit becomes a very crucial key block. In this paper, a 5.4Gbps half-rate bang-bang CDR is designed for the applications of high-speed graphic DRAM interface. The CDR consists of a half-rate bang-bang phase detector, a current-mirror charge-pump, a 2nd-order loop filter, and a 4-stage differential ring-type VCO. The PD automatically retimes and demultiplexes the data, generating two 2.7Gb/s sequences. The proposed circuit is realized in 66㎚ CMOS process. With input pseudo-random bit sequences (PRBS) of $2^{13}-1$, the post-layout simulations show 10psRMS clock jitter and $40ps_{p-p}$ retimed data jitter characteristics, and also the power dissipation of 80mW from a single 1.8V supply.

• The Korean Journal of Ceramics
• /
• v.6 no.2
• /
• pp.138-142
• /
• 2000

Thin film $LiNbO_3$MFS (metal-ferroelectric-semiconductor) capacitor showed improved characteristics such as low interface trap density, low interaction with Si substrate, and large remanent polarization. This paper reports ferroelectric $LiNbO_3$thin films grown directly on p-type Si (100) substrates by 13.56 MHz RF magnetron sputtering system for FRAM (ferroelectric random access memory) applications. RTA (rapid thermal anneal) treatment was performed for as-deposited films in an oxygen atmosphere at $600^{\circ}C$ for 60sec. We learned from X-ray diffraction that the RTA treated films were changed from amorphous to poly-crystalline $LiNbO_3$which exhibited (012), (015), (022), and (023) plane. Low temperature film growth and post RTA treatments improved the leakage current of $LiNbO_3$films while keeping other properties almost as same as high substrate temperature grown samples. The leakage current density of $LiNbO_3$films decreased from $10^{-5}$ to $10^{-7}$A/$\textrm{cm}^2$ after RTA treatment. Breakdown electric field of the films exhibited higher than 500 kV/cm. C-V curves showed the clockwise hysteresis which represents ferroelectric switching characteristics. Calculated dielectric constant of thin film $LiNbO_3$illustrated as high as 27.9. From ferroelectric measurement, the remanent polarization and coercive field were achieved as 1.37 $\muC/\textrm{cm}^2$ and 170 kV/cm, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.492-498
• /
• 2012

A hyper branched 10-butylphenothiazine with in-situ thermally curable methacrylate (1,3,5-tris-[$\{$10-Butyl-3-(4-(2-methyl-acryloyloxy)-phenyl)-7-yl-10H-phenothiazine$\}$]-benzene, (tris-PTMA)) was synthesized successfully. From the TGA thermogram of tris-PTMA was thermally stable up to $336^{\circ}C$. In the first heating scan of DSC thermogram, tris-PTMA showed glass transition temperature (Tg) at $140^{\circ}C$ and broad endothermic process in the region of $144-179^{\circ}C$, which is thermally curing temperature. In the second heating process, $T_g$ exhibited at $158.7^{\circ}C$ and endothermic process was not observed. Thermally cured tris-PTMA showed no big change in the UV-visible spectrum after washing with organic solvent such as methylene chloride, chloroform, toluene, indicating that thermally cured film was very good solvent resistance. Thermally cured tris-PTMA was electrochemically stable and the HOMO energy level of tris-PTMA was -5.54 eV. The maximum luminance efficiency of double layer structured polymer light-emitting diode based on in-situ thermally cured tris-PTMA was 0.685 cd/A at 16.0 V, which was higher than that of the device without thermally cured tris-PTMA (0.348 cd/A at 15.0 V).

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.39.2-39.2
• /
• 2010

In this work we have investigated electrical and optical properties of interface for ITO/Si with shallow doped emitter. The ITO is prepared by DC magnetron sputter on p-type monocrystalline silicon substrate. As an experimental result, The transmittance at 640nm spectra is obtained an average transmittance over 85% in the visible range of the optical spectrum. The energy bandgap of ITO at oxygen flow from 0% to 4% obtained between 3.57eV and 3.68eV (ITO : 3.75eV). The energy bandgap of ITO is depending on the thickness, sturcture and doping concentration. Because the bandgap and position of absorption edge for degenerated semiconductor oxide are determined by two competing mechanism; i) bandgap narrowing due to electron-electron and electron-impurity effects on the valance and conduction bands (> 3.38eV), ii) bandgap widening by the Burstein-Moss effect, a blocking of the lowest states of the conduction band by excess electrons( < 4.15eV). The resistivity of ITO layer obtained about $6{\times}10^{-4}{\Omega}cm$ at 4% of oxygen flow. In case of decrease resistivity of ITO, the carrier concentration and carrier mobility of ITO film will be increased. The contact resistance of ITO/Si with shallow doped emitter was measured by the transmission line method(TLM). As an experimental result, the contact resistance was obtained $0.0705{\Omega}cm^2$ at 2% oxygen flow. It is formed ohmic-contact of interface ITO/Si substrate. The emitter series resistance of ITO/Si with shallow doped emitter was obtained $0.1821{\Omega}cm^2$. Therefore, As an PC1D simulation result, the fill factor of EWT solar cell obtained above 80%. The details will be presented in conference.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.180-180
• /
• 2015

Solution processed Resistive random access memory (ReRAM)은 간단한 공정 과정, 고집적도, 저렴한 가격, 대면적화 플라즈마 데미지 최소화 등의 장점으로 차세대 비휘발성 메모리로 써 많은 관심을 받고 있으며, 주로 high-k 물질인 HfOx, TiOx, ZnO 가 이용 된다. IGZO와 ZTO와 같은 산화물 반도체는 높은 이동도, 대면적화, 넓은 밴드갭으로 인하여 투명한 장점으로 LCDs (Liquid crystal displays)에 이용 가능하며, 최근에는 IGZO와 ZTO에서 Resistive Switching (RS) 특성을 확인한 논문이 보고되면서 IGZO와 ZTO를 ReRAM의 switching medium와 TFT의 active material로써 동시에 활용하는 것에 많은 관심을 받고 있다. 이와 같은 산화물 반도체는 flat panel display 회로에 TFT와 ReRAM의 active layer로써 집적가능 하며 systems-on-panels (SOP)에 적용 가능하다. 하지만 IGZO 보다는 ZTO가 In과 Ga을 포함하지 않기 때문에 저렴하다. 그러므로 IGZO를 대신하는 물질로 ZTO가 각광 받고 있다. 본 실험에서는 ZTO film에 Al을 doping하여 메모리 특성을 평가하였다. 실험 방법으로는 p-type Si에 습식산화를 통하여 SiO2를 300 nm 성장시킨 기판을 사용하였다. 그리고 Electron beam evaporator를 이용하여 Ti를 10 nm, Pt를 100 nm 증착 한다. 용액은 Zn와 Tin의 비율을 1:1로 고정한 후 Al의 비율을 0, 0.1, 0.2의 비율로 용액을 각각 제작하였다. 이 용액을 이용하여 Pt 위에 spin coating방법을 이용하여 1000 rpm 10초, 6000 rpm 30초의 조건으로 AZTO (Al-ZnO-Tin-Oxide) 박막을 증착한 뒤, solvent 및 불순물 제거를 위하여 $250^{\circ}C$의 온도로 30분 동안 열처리를 진행하였다. 이후 Electron beam evaporator를 이용하여 top electrode인 Ti를 100 nm 증착하였다. 제작된 메모리의 전기적 특성은 HP 4156B semiconductor parameter analyzer를 이용하여 측정하였다. 측정 결과, AZTO (0:1:1, 0.1:1:1, 0.2:1:1)를 이용하여 제작한 ReRAM에서 RS특성을 얻었으며 104 s이상의 신뢰성 있는 data retention특성을 확인하였다. 그리고 Al의 비율이 증가할수록 on/off ratio가 증가하고 endurance 특성이 향상되는 것을 확인하였다. 결론적으로 Al을 doping함으로써 ZTO film의 메모리 특성을 향상 시켰으며 AZTO film을 메모리와 트랜지스터의 active layer로써 활용 가능할 것으로 기대된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.181.1-181.1
• /
• 2015

용액 공정을 이용한 Resistive random access memory (ReRAM)은 간단한 공정 과정, 대면적화, 저렴한 가격 등의 장점으로 인해 큰 관심을 받고 있으며, HfOx, TiOx, AlOx 등의 산화물이 ReRAM 절연 막으로 주로 연구되고 있다. 더 나아가 최근에는 organic 물질을 메모리 소자로 사용한 연구가 보고되고 있다. 이는 경제적이며, wearable 또는 flexible system에 적용이 용이하다. 그럼에도 불구하고, organic 물질을 갖는 메모리 소자는 기존의 산화물 소자에 비해 열에 취약하며 전기적인 특성과 신뢰성이 우수하지 못하다는 단점을 가지고 있다. 이를 위한 방안으로 본 연구에서는 AlOx - polymethylmethacrylate (PMMA) blended thin film ReRAM을 제안하였다. 이는 organic물질의 전기적 특성을 개선시킬 뿐 아니라, inorganic 물질을 wearable 소자에 적용했을 때 발생하는 crack과 같은 기계적 물리적 결함을 해결할 수 있는 새로운 방법이다. 먼저, P-type Si 위에 습식산화를 통하여 SiO2 300 nm 성장시킨 기판을 사용하여 electron beam evaporation으로 10 nm의 Ti, 100 nm의 Pt 층을 차례로 증착하였다. 그리고 PMMA 용액과 AlOx 용액을 초음파를 이용하여 혼합한 뒤, 이 용액을 Pt 하부 전극 상에서 spin coating방법으로 1000 rpm 10초, 5000 rpm 30초의 조건으로 증착하였다. Solvent 및 불순물 제거를 위하여 150, 180, $210^{\circ}C$의 온도로 30 분 동안 열처리를 진행하였고, shadow mask를 이용하여 상부 전극인 Ti를 sputtering 방식으로 100 nm 증착하였다. 150, 180, $210^{\circ}C$로 각각 열처리한 AlOx - PMMA blended ReRAM의 전기적 특성은 HP 4156B semiconductor parameter analyzer를 이용하여 측정하였다. 측정 결과 제작된 소자 전부에서 2 V이하의 낮은 동작전압, 안정된 DC endurance (>150cycles), 102 이상의 높은 on/off ratio를 확인하였고, 그 중 $180^{\circ}C$에서 열처리한 ReRAM은 더 높은 on/off ratio를 갖는 것을 확인하였다. 결론적으로 baking 온도를 최적화하였으며 AlOx - PMMA blended film ReRAM의 우수한 메모리 특성을 확인하였다. AlOx-PMMA blended film ReRAM은 organic과 inorganic의 장점을 갖는 wearable 및 system용 비휘발성 메모리소자에 적용이 가능한 경제적인 기술로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.211.1-211.1
• /
• 2015

최근 용액 공정을 이용한 산화물 반도체에 대한 연구가 활발히 진행되고 있다. 넓은 밴드갭을 가지고 있는 산화물 반도체는 높은 투과율을 가지고 있어 투명 디스플레이에 적용이 가능하다. 기존의 박막 진공증착 방법은 진공상태를 유지하기 위한 장비의 가격이 비싸며, 대면적의 어려움, 높은 생산단가 등으로 생산율이 높지 않다. 하지만 용액 공정을 이용하면 대기압에서 증착이 가능하고 대면적화가 가능하다. 그리고 각각의 조성비를 조절하는 것이 가능하다. 이러한 장점에도 불구하고, 소자의 신뢰성이나 저온공정은 중요한 이슈이다. Instability는 threshold voltage (Vth)의 shift 및 on/off switching의 신뢰성과 관련된 parameter이다. 용액은 소자의 전기적 특성을 열화 시키는 수분 과 탄소계열의 불순물을 다량 포함 하고 있어 고품질의 박막을 형성하기 위해서는 고온의 열처리가 필요하다. 기존의 열처리는 고온에서 장시간 이루어지기 때문에 유리나 플라스틱, 종이 기판의 소자에서는 불가능하지만 $100^{\circ}C$ 이하의 저온 공정인 microwave를 이용하면 유리, 플라스틱, 종이 기판에서도 적용이 가능하다. 본 연구에서는 산화물 반도체 중에서 InGaZnO (IGZO)를 용액 공정으로 제작한 juctionless thin-film transistor를 제작하여 기존의 열처리를 이용하여 처리한 소자와 microwave를 이용해서 열처리한 소자의 전기적 특성을 한 달 동안 관찰 하였다. 또한 In:Zn의 비율을 고정한 후 Ga의 비율을 달리하여 특성을 비교하였다. 먼저 p-type bulk silicon 위에 SiO2 산화막이 100 nm 증착된 기판에 RCA 클리닝을 진행 하였고, solution InGaZnO 용액을 spin coating 방식으로 증착하였다. Coating 후에, solvent와 수분을 제거하기 위해서 $180^{\circ}C$에서 10분 동안 baking공정을 하였다. 이후 furnace열처리와 microwave열처리를 비교하기 위해 post-deposition-annealing (PDA)으로 furnace N2 분위기에서 $600^{\circ}C$에서 30분, microwave를 1800 W로 2분 동안 각각의 샘플에 진행하였다. 또한, HP 4156B semiconductor parameter analyzer를 이용하여 제작된 TFT의 transfer curve를 측정하였다. 그 결과, microwave 열처리한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 높은 mobility, 낮은 hysteresis 값을 나타내었으며, 1달간 소자의 특성을 관찰하였을 때 microwave 열처리한 소자의 경우 전기적 특성이 거의 변하지 않는 것을 확인하였다. 따라서 향후 용액공정, 저온공정을 요구하는 소자 공정에 있어 열처리방법으로 microwave를 이용한 활용이 기대된다.