• Biotechnology and Bioprocess Engineering:BBE
• /
• v.2 no.2
• /
• pp.73-76
• /
• 1997

Biopolymer membrane was prepared using two oppositely charged natural biopolymer. The biopolymer membrane was used for the encapsulation of two hybridoma cell lines(ATCC CRL-1606, ATCC BH-8852) to produce monoclonal antibodies. In order to reduce the down stream steps, the pore size of the membrane was controlled to retain the monoclonal antibodies in the capsules based on the diffusion experiments with standard proteins. T-flask culture showed cell densities of 8$\times$107cells/mL 3$\times$107cells/mL, and MAb concentrations of 506 $\mu\textrm{g}$/mL and 109$\mu\textrm{g}$/mL for encapsulated ATCC CRL-1606 and HB-8852, respectively. Two liter perfusion culture with encapsulated ATCC HB-8852 was performed to enhance the MAb production. The MAb production of the encapsulated hybridoma increased considerably comparing to the culture using silicone tubing for oxygen transfer.

• KSBB Journal
• /
• v.5 no.3
• /
• pp.207-214
• /
• 1990

Growth properties of carrot hairy roots transformed by Agrobacterium rhizogenes were compared in flask and bioreactor. Oxygen transfer coefficient KLa was measured during the cultivation in bioreactor. In flask cultures, initially sucrose 30g/l was nearly exhausted after 20days. pH was dropped from initially 5.8 to 4.79 after 4 days, but it is stable after that time. Finally, after 28 days, hairy roots were grown about twelve times. In view of the results studied optimum conditions, hairy roots were maintained high growth rates in sucrose 50g/l, pH 5.8, total nitrogen 60mM. Also in bioreactor cultures, fixed stainless sieve in bottom and aerated 0.31 vvm, the results of cultivation by the use of sucrose 50g/l had grown about twenty-eight times and pH variations were liked in flask. As a results, growth rate of 1.756g fresh weight/day/g inoculum in bioreactor were higher about three times than 0.57g fresh weight/day/g inoculum in flask culture. KLa values were showed a tendency to decrease from 0.209 min-1 to 0.068 min-1.

• Journal of the Korean Society of Combustion
• /
• v.5 no.1
• /
• pp.1-6
• /
• 2000

Surface reaction occurs at a certain surface temperature when a catalyst is heated up in a reactive mixture. If homogeneous ignition does not occur, a steady state is observed because the heat produced by the surface reaction is balanced with the heat loss caused by convection, conduction and radiation. The present paper treats the effects of pressure on the surface temperature at the steady state. Hydrogen and oxygen are used as reactants and nitrogen as an inert gas. A spherical platinum catalyst of 1.5 mm in diameter is sustained in the chamber with two wires of 0.1 mm in diameter. As results, there exists a maximum steady temperature at a certain relative hydrogen concentration which increases with total pressure. At the steady state, it can be approximated that the heat release is estimated by the mass transfer considering the effect of natural convection. The experimental results are explained qualitatively by the approximation.

• Journal of Astronomy and Space Sciences
• /
• v.9 no.2
• /
• pp.183-192
• /
• 1992

We have investigated the properties of dust grains in the envelopes of infrared carbon stars by testing various radiative transfer model spectra with different stellar and enveloped parameters. We have deduced a new opacity pattern for the dust grains reflecting both the experimental data and the model fitting with recent infrared observations. The best pattern we find is very similar to amorphous carbon with a slight modification that could be attributed to some unknown dust grain materials. Unlike oxygen-rich dust grains, the optical properties of carbon grains do not show any reasonable tendency of temperature dependence. We find that the Planck mean values of radiation pressure efficiency factors for the modified amorphous carbon are much larger than those for graphite.

• Rapid Communication in Photoscience
• /
• v.4 no.3
• /
• pp.73-75
• /
• 2015

Cr(VI) reduction was successfully achieved in the presence of cationic micelles (CMs) under visible light illumination. Micelle formation of cationic surfactants seems to be critical in Cr(VI) reduction. Cr(VI) was reduced very fast above the critical micelle concentration (cmc) of CTAB solutions, but was not reduced at all either below or around the cmc of CTAB. The reduction rate of Cr(VI) was enhanced in the absence of dissolved oxygen, supporting that the removal of Cr(VI) should be achieved via a reductive pathway. When CTAB was substituted by Brij 35 or SDS, the reduction of Cr(VI) was negligible. This indicates that the electrostatic interaction between Cr(VI) and headgroups of surfactants is important in the visible light-induced Cr(VI) reduction in micellar solutions.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.477-482
• /
• 1995

A computer simulation model of various smelting process for melting waste sand was developed by using energy and material balance concept. This model can predict the coal, flux and oxygen consumption and the volume and temperature of off-gas. The major critical variables for smelting process can be explained by using the analysis of energy and material balance. The major conclusions were as follows; 1. The most important variables for smelting process were high post-combustion ratio, high heat transfer efficiency and refractory protection technology. 2. For saving energy in this smelting process, selection of raw materials i.e coal, flux are very important, espacially using of low volatile coal is very profitable. 3. The treatment cost of waste sand is high and environmental restriction is severe, in this reason we must be concerned in the treatment of waste sand by smelting process.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.8 no.5
• /
• pp.303-305
• /
• 2003

Scale-up of hirudin production from Saccharomyces cerevisiae from bench-scale to pilot-scale was carried out based on constant volumetric oxygen transfer coefficient (K$\sub$L/a). Fed-batch mode of cultivation using step-wise feeding strategy of galactose was employed for the production of hirudin in a 30-L and a 300-L pilot-scale fermentor. The final hirudin concentrations were achieved 390 mg/L and 286.1 mg/L, and the volumetric productivities were 80.4% and 90.7% with the 30-L and 300-L fermentors, respectively, compared to the productivity of the 5-L bench-scale fermentor.

• Journal of Korea Foundry Society
• /
• v.11 no.6
• /
• pp.482-490
• /
• 1991

This study presents the wear characteristics of Ti alloys (Pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn) fabricated by centrifugal precision casting in an Ohara dental titanium casting machine. It was found that the hardness of the surface region is higher than that of the interior region. It is considered that the oxygen adsorption in the surface region during casting, leads to the interstitial solid solution hardening. Wear resistance incerases in the order of pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn alloys. The interior hardness value increases in the same order. The specific wear rate increases with applied load and increases monotonously with sliding speed. The Fe transfer from the counterpart material was observed on the worn surface of the Ti-5Al-2.5Sn alloy. Oxidative wear occurs at low sliding speeds and mechanical fracture wear occurs at high sliding speeds.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2809-2812
• /
• 2010

The Chemical Doping of epitaxial graphene (EG) due to p-tert-butylcalix[4]arene was investigated using high resolution photoemission spectroscopy (HRPES). The measured work function changes verified that increased adsorption of the p-tert-butylcalix[4]arene on EG showed p-type doping characteristics due to charge transfer from the graphene to the p-tert-butylcalix[4]arene through the hydroxyl group. A single oxygen bonding feature associated with the O 1s peak was clearly observed in the core-level spectra, indicating the presence of one equivalent adsorption state.

• Carbon letters
• /
• v.23
• /
• pp.55-62
• /
• 2017

We report on the dispersion state of partially reduced graphene oxide (PRGO) in organic solvents, namely methyl ethyl ketone, ethyl acetate, methylene chloride, toluene, and xylene, by controlling the carbon to oxygen (C/O) atomic ratio of the PRGOs. A two-phase solvent exchange method is also proposed to transfer PRGO from water to an aprotic solvent, such as methyl ethyl ketone. We achieve relatively good dispersion in aprotic and non-polar solvents by controlling the C/O atomic ratio of the PRGOs and applying the two-phase solvent exchange method. There is an increase in the glass transition temperatures with the dispersion of PRGOs into amorphous polymers, in particular a $4.4^{\circ}C$ increase for poly(methyl methacrylate) and $3.0^{\circ}C$ increase for polycarbonate. Good dispersion of PRGO in a nonpolar polymer, such as linear low density polyethylene, is also obtained.