• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.417-424
• /
• 1999

Laser lapping of diamond films is performed with focused beam of copper vapor laser. Both spherical and rod-shape laser beam are used. Diamond surface is scanned at various scan speeds(0,125, 0.5, 0.75 mm/sec) and baem shifts (5, 10, 20, 40, 100$\mu\textrm{m}$) At 0.125 mm/sec 10$\mu\textrm{m}$ scan condition the level difference of di-amond surface of about 700$\mu\textrm{m}$ over 20 mm is reduced to 200$\mu\textrm{m}$ In addition surface roughness is also im-proved from 3.53$\mu\textrm{m}$ to 2.47$\mu\textrm{m}$ at 5$\mu\textrm{m}$ beam shift. But at higher beam shift than 10$\mu\textrm{m}$ laser scan makes the surface rougher which is considered to be due to the non uniform spatial distribution of laser en-ergy. It is concluded that homogenized laser beam with high average power is needed for large area laser lapping of diamond films at appreciable rates.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.220-220
• /
• 2013

Surface-normal transmission electro-absorption modulator (EAM) are attractive for high-definition (HD) three-dimensional (3D) imaging application due to its features such as small system volume and simple epitaxial structure [1,2]. However, EAM in order to be used for HD 3D imaging system requires uniform modulation performance over large area. To achieve highly uniform modulation performance of EAM at the operating wavelength of 850 nm, it is extremely important to remove the GaAs substrate over large area since GaAs material has high absorption coefficient below 870 nm which corresponds to band-edge energy of GaAs (1.424 eV). In this study, we propose and experimentally demonstrate a transmission EAM in which highly selective backside etching methods which include lapping, dry etching and wet etching is carried out to remove the GaAs substrate for achieving highly uniform modulation performance. First, lapping process on GaAs substrate was carried out for different lapping speeds (5 rpm, 7 rpm, 10 rpm) and the thickness was measured over different areas of surface. For a lapping speed of 5 rpm, a highly uniform surface over a large area ($2{\times}1\;mm^2$) was obtained. Second, optimization of inductive coupled plasma-reactive ion etching (ICP-RIE) was carried out to achieve anisotropy and high etch rate. The dry etching carried out using a gas mixture of SiCl4 and Ar, each having a flow rate of 10 sccm and 40 sccm, respectively with an RF power of 50 W, ICP power of 400 W and chamber pressure of 2 mTorr was the optimum etching condition. Last, the rest of GaAs substrate was successfully removed by highly selective backside wet etching with pH adjusted solution of citric acid and hydrogen peroxide. Citric acid/hydrogen peroxide etching solution having a volume ratio of 5:1 was the best etching condition which provides not only high selectivity of 235:1 between GaAs and AlAs but also good etching profile [3]. The fabricated transmission EAM array have an amplitude modulation of more than 50% at the bias voltage of -9 V and maintains high uniformity of >90% over large area ($2{\times}1\;mm^2$). These results show that the fabricated transmission EAM with substrate removed is an excellent candidate to be used as an optical shutter for HD 3D imaging application.

• Tribology and Lubricants
• /
• v.32 no.2
• /
• pp.44-49
• /
• 2016

Diamond mechanical polishing (DMP) is a crucial process in a sapphire wafering process to improve flatness and achieve the target thickness by using free abrasives. In a DMP process, material removal rate (MRR) is a key factor to reduce process time and cost. Controlling mechanical parameters, such as velocity and pressure, can increase the MRR in a DMP process. However, there are limitations of using high velocities and pressures for achieving a high MRR owing to their side effects. In this paper, we present the lapping characteristics and improvement of MRR by using a fixed abrasive plate through an experimental study. The change in MRR as a function of velocity and pressure follows Preston's equation. The surface roughness of a wafer decreases as the plate velocity and pressure increases. We observe a sharp decrease in MRR over the lapping time at a high velocity and pressure in the velocity and pressure test. An analysis of surface roughness (Rq and Rpk) indicates that wear of abrasives decreases the MRR sharply. In order to investigate the effect of abrasive wear on the MRR, we utilize a cutting fluid and a rough wafer. The cutting fluid delays the wear of abrasives resulting in improvement of MRR drop. The rough wafer maintains the MRR at a stable rate by self-dressing.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.7 no.2
• /
• pp.59-65
• /
• 1982

In this paper, the CdS single crystal, which was grown as piper-polish method, was Ion-bombarded with Sb and In, and the thermally stimulated current of the spot that was Ionbombarded was measured. In the sample which was individually bombarded by Sb and In, the over-lapping peak was found, this over lapping peak was separated, by the method of thermal cleaning, showing the trap levels of 0.25(eV) and 0.31(eV) at the temperature of 147(K) and 181(K). While the spot is being cooled down and excited with photolight at the same time, the trap level 0.25(eV) disappeared and the new trap level of 0.85(eV) appeared. It can be said that the better photo-conductive crystals, the T.S.C is better measured.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.76-80
• /
• 2018

The present study investigates the hydrodynamic force acting on the vertical wall of a portable water storage tank which has reentrant bottom topology. To numerically simulate the lapping waves in the tank, functional iterative method for the linearized Peregrine's model which numerically simulates the propagating waves over the slowly-sloped bottom topology is introduced. The numerical experiment condition is controlled to adjust the position and the height of the water supplying nozzle. Finally, it is observed that the maximum wave height at the vertical wall and the ratio of hydrodynamic force to hydrostatic one are amplified accordingly. Therefore it must be give attention to this bad effect of amplified hydrodynamic force by the supply method of fire water in order to have the structural stability of the portable water storage tank when it was used on the reentrant bottom topography.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.442-450
• /
• 2006

This paper describes the new modal analysis method to detect the presence of the breathing crack in a general rotor system with disk asymmetry and stator anisotropy. It is proposed that the modal analysis using directional frequency response functions (dFRFs), which, accounting for the directivity in modes, clears the heavily over-lapping of other harmonics occurring from non-isotropic properties in addition to those due to crack, can provide an effective method to detect the modes by a crack. The simulations from the simple general rotor model show that the r-dFRFs (reverse dFRFs) for asymmetry confirms a good indicator of the presence of the breathing crack and the instability is primarily influenced by the shaft asymmetry than the breathing crack.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.03a
• /
• pp.16-19
• /
• 1998

본 논문에서는 생물학적인 DNA와 인위적인 DNA의 개발 메커니즘에 근거를 둔 새로운 DNA coding mithod를 소개한다. 이 방법은 DNA 유전자의 Redundancy 성질과 Over-lapping 성질을 분석하여 구성한 알고리즘으로, DNA 자체의 특성 때문에 염색체의 길이를 자유자재로 변화시킬 수 있는 장점을 가지고 있다. 즉 삽입과 삭제의 과정을 쉽게 처리할 수 있다. 따라서 본 연구에서는 이 DNA coding method를 사용하여 시스템 제어에 필요한 지식을 표현하는 적당한 퍼지규칙을, 전건부와 후건부의 구조 및 매개변수 동조를 통하여, 획득하고, 이 규칙을 새로운 유전자 알고리즘을 이용하여 최적화 시킬 수 있는 새로운 퍼지규칙 획득 알고리즘을 개발한다. 이 방법의 유용성을 입증하기 위하여 물탱크 시스템에 적용한 결과 효과적으로 퍼지규칙을 획득한다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.21-25
• /
• 2008

In this paper, the temperature history and the strength development of concrete corresponded to various bubble sheets layer and curing temperature. Based on the results, In case of the test temperature of -5℃, concrete subject in the exposure condition, result in a frost damage at initial stage by a fall of below zero temperature. In case of the combination of PE film and non woven fabric was after 36 hour, and combination of bubble sheet over double, a tremendous insulating effect of bubble sheet over double is confirmed due to the temperature of concrete fall of below zero temperature after 60 hours. Meanwhile, regarding the -15℃ of temperature, special measure for insulation curing is necessary to secure stability against early frost damage because frost damage was not affected by the lapping thickness of bubble sheet subjected to severe cold weather condition.

• The Research Journal of the Costume Culture
• /
• v.12 no.5
• /
• pp.880-896
• /
• 2004

Trompe l'Oeil technique strategically conceived with a view to effectively realize creative ideas among the expression techniques of fine arts style has provided the driving force in development of fine arts and has continuously influenced development of the modem fashion pursuing unique individuality. The study is focused first on finding out how Trompe l'Oeil technique originated in connection with researching the fashion of Trompe l'Oeil and on analysing the technique of expression. The author referred to fashion magazines for designing ideas of Trompe l'Oeil represented in modem fashion in practical applications used by designers in Paris, Italy, London and New York during the 10 year period(1990-1999). The collections of data were analyzed as following: Effectiveness depending on the method of Trompe l'Oeil I. Effectiveness of Layering: when two clothing are over lapped or coordinated with one another in color or style. 2. Effectiveness of Detailing: when pictures, stitch, tape, cutting, quilting and etc are used to create collar, pocket, yoke, zipper, string, shadow and etc. 3. Effectiveness of Accessories: when the image of necklace, belt, tie, tassel, badges and stars are represented by illustration or embroidery on clothing to substitute the actual existence. 4. Effectiveness of Nudity: when human body is realistically drawn and printed on clothing.

• Culinary science and hospitality research
• /
• v.14 no.2
• /
• pp.293-302
• /
• 2008

The objective of this study is to suggest development methods of marine tour complexes by specializing and modernizing the renowned Jagalchi Fish Market. This study tries to suggest the ways of overcoming limitations of the traditional market place and making a unique tourism destination with affluent attractive culture elements. To preserve its position as the most famous fish market in Korea, Jagalchi market needs to more differentiate its position over competitors. To do that, it needs to avoid over-lapping of product categories among different sectors and specializing each zone according to the assigned theme. Improving tourism environments by expanding entertaining aspects, building landmark facilities and a seaside park, and tourism infrastructures. In addition, the development scheme needs to be planned unified with other city development plans to create a unified image, and a connection program with other tourism resources surrounding the target area needs to be created in order to pursue synergy effects. In the aspect of food, a large seafood center which offers various seafood from all around the world, a traditional night market street, various theme restaurants can be suggested. Successful development of the Jagalchi marine tour complexes not only has ripple effects on the region's culture, society, and other related industries but directly influences related regional tourism and commercial industry.