• Journal of the Korean earth science society
• /
• v.38 no.2
• /
• pp.150-160
• /
• 2017

In order to determine the porosity of rock, the 'standard test method for porosity and density of rock' proposed by the Korean Society for Rock Mechanics is commonly used. However, the standard test method, which uses a drying oven, takes 8 to 24 hours to complete the test in taking samples out of the oven every four hours and measuring the weight of the specimen. To complement these disadvantages, we devised a method for measuring rock porosity by using a microwave oven. The devised method reduced the cause of errors and the inconvenience occurred in the process of weighing samples by constructing a weight monitoring system, which monitors the drying process. A suitable heating/pause time was set up to maintain the temperature of sample below $105{\pm}3^{\circ}C$ in drying process, and an alarm system was implemented in order to stop drying process when the weight change of the rock sample is within 0.1% of the initial weight. The porosity was determined from the dry weight of the sample, which was obtained by the curve fitting of weight monitoring data. Then, the porosities obtained by using the microwave oven were compared with those obtained by the standard test method. Test results using sandstone samples showed that the porosities obtained by a microwave oven was similar to those obtained by the standard method and the porosity difference between two methods was as large as 0.4%. In addition, repeated porosity measurement using the same specimen showed that the standard deviation of the porosity, which reflects the precision of the measurement was as good as 0.23%. Therefore, a microwave oven porosity measurement system can give the porosity of rock samples with high reliability.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.3
• /
• pp.393-398
• /
• 1998

The loss of ascorbic acid in dried red pepper leaves prepare with different drying methods of air-, oven-, microwave oven-, and vacuum drying with blanching or without was determined by a HPLC method. Vacuum drying showed the least loss of ascorbic acid than the other drying methods. Additionally, the feasibility of near infrared reflectance spectroscopy(NIRS) to determine the contents of ascorbic acid in the red pepper leaves was studied. NIRS was found to be an efficient way of determining ascorbic acid contents in red pepper leaves, requiring only 30 seconds of an analytical time.

• Journal of environmental and Sanitary engineering
• /
• v.13 no.3
• /
• pp.133-140
• /
• 1998

The food wastes from a refectory and an eating house were heated in domestic microwave oven(700W) equipped with a fan and the drying rates and destruction of microorganisms were investigated. The drying rate was decreased with the size of food waste and the food wastes in polypropylene basket were dried faster than that on glass dish. The rate was increased with lower initial moisture content. Death rate of microorganisms was also decreased with the size of food waste. Ninety eight percent of reduction in viable cell numbers for the 400g of food waste could be achieved in 240sec of microwave irradiation. The growth of microorganisms in food wastes after microwave irradiated was observed at $32^{\circ}C$ and 95% relative humidity after 7days and the cell numbers in microwave irradiated food wastes were found to be 1/2 ~ 1/20 of the numbers in untreated wastes in accordance with the mass and the length of exposed time to microwave. To minimize the moisture and microorganisms in food wastes, the use of microwave oven are recommended.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.2
• /
• pp.143-152
• /
• 2023

In this research, the microwave oven drying method was investigated as a potential accurate testing approach for determining the water content of fresh concrete. To do so, water content estimation formulas employed in three prominent oven drying test methods were selected, and the calculation principles for each equation, along with potential error factors arising during the actual testing process, were considered. Moreover, a concrete test was conducted to validate the possible error factors. Consequently, it was confirmed that estimation errors in the water content of fresh concrete can occur due to sample deviations arising during the wet screening process for creating mortar specimens or deviations in the coarse aggregate sampling quantity during the sample collection process.

• Journal of the Korea Furniture Society
• /
• v.27 no.1
• /
• pp.43-48
• /
• 2016

PEG (Polyethylene glycol) impregnation in wood reduces the occurrence of checking during kiln drying. The volumetric shrinkages of wood PEG impregnated by pressure (PEG-P) or soaking (PEG-S) methods, and oven-dried by vent (VD) or air-tight (AD) methods were measured and compared with the controls. The average oven-dry weight of PEG impregnated specimens was larger than that of the controls by 3.6 g, but was not influenced by the drying methods. The average of the total volumetric shrinkage of PEG-P-VD specimens was the least (2.3%), while that of CON-S-AD specimens was the largest (28.9%). Within a drying method the total volumetric shrinkage of the control was the largest followed by PEG-S and PEG-P specimens, which implied that residual PEG in wood restrained its shrinkage during drying.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.14 no.2
• /
• pp.95-98
• /
• 1985

This study was carried out to investigate changes in the compositions of fatty acids according to the different drying methods of raw mugwort. Raw mugwort from Kang-wha was dried with four methods such as sun-drying, shady sun-drying, heated oven-drying and freeze-drying. Total contents and fatty acid compositions of the ethyl ether extracts from the dried mugworts were examined. Total contents of the ethyl ether extracts showed remarkable differences with drying methods; freeze-dried mugwort had the highest content (5.60%), while oven dried mugwort revealed the lowest content (2.45%). Eleven fatty acids and four unknown peaks were identified by gas-liquid chromatography; major fatty acids were linoleic acid, linolenic acid and palmitic acid. Fatty acids of mugworts dried by 4 different methods were the same in kinds, but different in their compositions. The content of polyunsaturated fatty acids $(C_{18:2}+C_{18:3})$ was the highest and the loss of low volatile fatty acids was the least in mugwort dried by the freeze-drying method. The volatile fatty acids considerably decreased in oven-dried mugwort. However, the contents of polyunsaturated fatty acids were a little higher in oven-dried mugwort than in sun-dried and shady sun-dried mugwort, and the lowest in sun-dried mugwort.

• BMB Reports
• /
• v.45 no.2
• /
• pp.91-95
• /
• 2012

Glutamate dehydrogenase from axenic bacterial cultures of a new microorganism, called GWE1, isolated from the interior of a sterilization drying oven, was purified by anion-exchange and molecular-exclusion liquid chromatography. The apparent molecular mass of the native enzyme was 250.5 kDa and was shown to be an hexamer with similar subunits of molecular mass 40.5 kDa. For glutamate oxidation, the enzyme showed an optimal pH and temperature of 8.0 and $70^{\circ}C$, respectively. In contrast to other glutamate dehydrogenases isolated from bacteria, the enzyme isolated in this study can use both $NAD^+$ and $NADP^+$ as electron acceptors, displaying more affinity for $NADP^+$ than for $NAD^+$. No activity was detected with NADH or NADPH, 2-oxoglutarate and ammonia. The enzyme was exceptionally thermostable, maintaining more than 70% of activity after incubating at $100^{\circ}C$ for more than five hours suggesting being one of the most thermoestable enzymes reported in the family of dehydrogenases.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.69-74
• /
• 2000

Pinus $rigida{\times}taeda$ and Liriodendron tulipifira have been planted in this country for about 20 years. They are known as a relatively 13st-grown and useful species. The physical properties such as green moisture contents, specific gravities and dimensional shrinkages were examined with natively grown timbers. The kiln-dry schedules were developed with 30m thick boards by using an oven-fast-drying method. In both species the green MC's of sapwoods were higher than those of heartwoods, but their discrepancies were small. The green specific gravities of Pinus $rigida{\times}taeda$ and Liriodendron tulipifera were 0.48 and 0.41~O.42, respectively. The developed kiln-dry schedules were proven to minimize drying defects for the hoards of 30mm thickness and various width.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.1
• /
• pp.10-15
• /
• 2003

This study was carried out to investigate a radial distribution of moisture contents(MCs) within a log cross section(LC) during oven-drying of circumferential slices cut from some of domestic hardwoods LCs. For zelkova, the slices from sapwood and from transition part already reached to below hygroscopic range at 30% in average MC, whereas the innermost slice represented about 40% MC. A moisture gradient between the innermost slice and the adjacent slice from a cherry LC became severer with drying times. For castor aralia, the green MC for heartwood slices was approximately 23% higher than that for sapwood slices, and the similar moisture gradient still lasted until average 15% MC during oven-drying. For Chinese mahogany, the MCs of the mixed slices and the innermost slice were lower than those of the slices cut from the other parts during all over drying stage.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.101-111
• /
• 2014

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaining (BR) and bark-remaining-coating (BRC) treatments on the air circulating oven-drying characteristics of Japanese larch hollowed round-post was evaluated. The drying times of the hollowed round-posts for control, VD, HCO and BR specimens were 72, 168, 204 and 240 hours, respectively, from the initial MC to about 8% MC, which was recommended as the indoor in-use MC. The temperature in the hole of the VD specimen was lower than that of wood and the difference between air temperature in the hole and wood temperature became large during drying period. The vapor pressure of air in the hole was higher than that of inside wood for all specimens except VD specimen. The surface checks on all specimens were observed in increasing order of BR, BRC, UC, HCO and VD specimens.