• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.4
• /
• pp.249-255
• /
• 2021

A novel current balancing technique for multichannel light-emitting diode (LED) that uses a series resonance and coupled inductor is proposed in this paper. The proposed LED driver balances output currents through frequency control and enables zero-voltage switching. The proposed converter utilizes the charge balance condition of the resonant capacitor and the current sharing function of the coupled inductor to achieve whole LED current balancing without an additional controller. The proposed coupled inductor can integrate the current balancing function and the resonant inductor, so the power density can be increased by reducing the number of magnetic devices. A 40 W prototype is built to verify the validity of this LED driver, and the experimental results are successfully obtained.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.777-788
• /
• 2014

This paper presents a wide output range, high power efficiency reconfigurable charge pump for driving touch panels with the high resistances. The charge pump is composed of 4-stages and its configuration automatically changes based on the required output voltage level. In order to keep the power efficiency over the wide output voltage range, internal blocks are automatically activated or deactivated by the clock driver in the reconfigurable charge pump minimizing the switching power loss due to the On and Off operations of MOSFET. In addition, the leakage current paths in each mode are blocked to compensate for the variation of power efficiency with respect to the wide output voltage range. This chip is fabricated using $0.18{\mu}m$ BCD process with high power MOSFET options, and the die area is $1870{\mu}m{\times}1430{\mu}m$. The power consumption of the charge pump itself is 79.13 mW when the output power is 415.45 mW at the high voltage mode, while it is 20.097 mW when the output power is 89.903 mW at the low voltage mode. The measured maximum power efficiency is 84.01 %, when the output voltage is from 7.43 V to 12.23 V.

• Journal of Hydrogen and New Energy
• /
• v.34 no.5
• /
• pp.398-412
• /
• 2023

The Korean government is actively promoting the hydrogen industry as a key driver of economic growth. This commitment is evident in the 2019 hydrogen economy activation roadmap and the 2021 basic plan for hydrogen economy implementation. This study quantitatively analyzes the economic impact of the hydrogen economy using input-output analysis based on the Bank of Korea's 2019 input-output table, projecting its size by 2050. Four parts dealt with production-inducing, value-added creation, employment-inducing, and wage-inducing based on a demand-driven model. The results reveal that transportation had the most remarkable economic effect throughout the hydrogen economy, and production was the least. The hydrogen economy is projected to reach 71.2 trillion won by 2050.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.51-57
• /
• 2010

A CMOS rail-to-rail high voltage buffer amplifier is proposed to drive the gamma correction reference voltage of large TFT LCD panels. It is operating by a single supply and only shows current consumption of 0.5mA at 18V power supply voltage. The circuit is designed to drive the gamma correction voltage of 8-bit or 10-bit high resolution TFT LCD panels. The buffer has high slew rate, 0.5mA static current and 1k$\Omega$ resistive and capacitive load driving capability. Also, it offers wide supply range, offset voltages below 50mV at 5mA constant output current, and below 2.5mV input referred offset voltage. To achieve wide-swing input and output dynamic range, current mirrored n-channel differential amplifier, p-channel differential amplifier, a class-AB push-pull output stage and a input level detector using hysteresis comparator are applied. The proposed circuit is realized in a high voltage 0.18um 18V CMOS process technology for display driver IC. The circuit operates at supply voltages from 8V to 18V.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.2
• /
• pp.15-22
• /
• 2012

A low power consumption scan driver using depletion-mode n-type InGaZnO thin-film transistors is proposed. The proposed circuit uses 2 clock signals and generates the non-overlap output signals without the additional masking signals and circuits. The power consumption of the proposed circuit is decreased by reducing the number of the clock signals and short circuit current. The simulation results show that the proposed circuit operates successfully when the threshold voltage of TFT is varied from -3.0V to 1.0V. The proposed scan driver consumes 4.89mW when the positive and negative supply voltage is 15V and -5V, respectively, and the operating frequency is 46KHz on the XGA resolution panel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.8
• /
• pp.905-910
• /
• 2010

In this paper, visible light communication(VLC) system modulated by a switching driver circuit of lighting light emitting diode(LED), not only for illumination but also for optical wireless communication, is implemented. Presented system could overcome the drawbacks of prior linear modulation technique such as low efficiency, heat generation, and limits to realization of high power lighting LED. Experimental results from the realized digital audio system are presented to confirm the superiority of the proposed circuit. Our prototype achieves a transmission data rate of 10 Mbps with a radius of 1.5 meters using 20 W output power, and the signals were detected successfully.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.4
• /
• pp.49-58
• /
• 2014

A low-swing differential near-ground signaling (NGS) transceiver for low-power high-speed mobile I/O interface is presented. The proposed transmitter adopts an on-chip regulated programmable-swing voltage-mode driver and a pre-driver with asymmetric rising/falling time. The proposed receiver utilizes a new multiple gain-path differential amplifier with feed-forward capacitors that boost high-frequency gain. Also, the receiver incorporates a new adaptive bias generator to compensate the input common-mode variation due to the variable output swing of the transmitter and to minimize the current mismatch of the receiver's input stage amplifier. The use of the new simple and effective impedance matching techniques applied in the transmitter and receiver results in good signal integrity and high power efficiency. The proposed transceiver designed in a 65-nm CMOS technology achieves a data rate of 13 Gbps/channel and 0.3 pJ/bit (= 0.3 mW/Gbps) high power efficiency over a 10 cm FR4 printed circuit board.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.4
• /
• pp.247-258
• /
• 2017

Since 2016 when the regulations related to vehicle structure and device modification were drastically revised, the car tuning market has been growing rapidly. Particularly, many drivers are showing interest in changing the interior and exterior according to their preference, or improving the specifications of their cars by changing the engine and powertrain, among others. Also, as the initial engine settings such as horse power and torque of the vehicle are made for stable driving of the vehicle, it is possible to change the engine performance, via Engine Control Unit (ECU) mapping, to the driver's preference. However, traditionally, ECU mapping could be only performed by professional car engineers and the settings were also decided by them. Therefore, this study proposed a system that collects data related to the driver's driving habits for a certain period and sends them to a cloud server in order to analyze them and recommend ECU mapping values. The traditional mapping method only aimed to improve the car's performance and, therefore, if the changes were not compatible with the driver's driving habits, could cause problems such as incomplete combustion or low fuel efficiency. However, the proposed system allows drivers to set legally permitted ECU mapping based on analysis of their driving habits, and, therefore, different drivers can set it differently according to the vehicle specifications and driving habits. As a result, the system can optimize the car performance by improving output, fuel efficiency, etc. within the range that is legally permitted.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4A
• /
• pp.408-416
• /
• 2010

A dumbbell-type CPW transmission-line structure has been proposed to improve the return loss of the transmission line between a driver IC and flip-chip-bonding VCSEL(Vertical Cavity Surface Emitting Laser) in a hybrid opto-electric circuit board(OECB). The proposed structure used a pair of dummy ground solder balls on the ground lines for flip-chip bonding of the VCSEL and designed the dumbbell-type CPW transmission line to improve reflection characteristics. The simulated results revealed that the return loss of the dumbbell-type CPW transmission line was 13-dB lower than the conventional CPW transmission line. A 4-dB improvement in the return loss was obtained using the dummy ground solder balls on the ground lines. The variation rate of the reflection characteristic with the variation of terminal impedances of the transmission line (at the output terminal of the driver IC and the input terminal of the VCSEL) is about ${\pm}2.5\;dB$.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2116-2118
• /
• 2000

In the technique of Q-switching, very fast electronically controlled optical shutters can be made by using the electro-optic effect in crystals or liquids. The driver for the Pockels cell must be a high-speed, high-voltage switch which also must deliver a sizeable current. Common switching techniques include the use of vacuum tubes, cold cathode tubes, thyratrons, SCRs, and avalanche transistors. Semiconductor devices such as SCRs, avalanche transistors, and MOSFETs have been successfully employed to drive Pockels cell Q-switch. In this study, a simple driver for the Pockels cell Q-switch was developed by using SCRs, pulse transformer and TTL ICs. The Pockels cell Q-switch which was operated by this driver was employed in pulsed Nd:YAG laser system to investigate the operating characteristics of this Q-switch. And we have investigated the output characteristics of this Q-switch as a function of the Q-switch delay time to Xe flashlamp current on.