• Journal of Korea Foundry Society
• /
• v.11 no.5
• /
• pp.392-397
• /
• 1991

This study has been performed to investigate the austempering heat treatment response and mechanical properties of a high carbon(0.9%), silicon(1.5-4.5%)-alloyed cast steel, with a chemical composition similar to that of the matrix of a ductile cast iron. Tensile and hardness tests were used to evaluate the effects of a wide variety of austempering heat treatment variables. SEM metallography and X-ray measurements of stabilized austenite were also performed for all the specimens employed. The austempered microstructures which contain up to 39% stabilized austenite were obtained. Mechanical properties and microstructures depended primarily on the austempering time and temperature. The optimum mechanical properties were obtained at the chemical compositions of 0.9% C and 2.5% Si.

• KSBB Journal
• /
• v.14 no.4
• /
• pp.470-475
• /
• 1999

Several enzyme were applied to Laubholz Bleached Kraft Pulp(LBKP) to evaluate the influence on beatability which was measured in Schopper Riegler value, and the results were compared with untreated pulp. Among the types of enzyme, cellulase was found to be the most effective. Addition of cellulase increased the beatability by 28% at optimum condition. Strength properties such as tensile strength and folding endurance also increased with enzymatic treatment by 12% and 46%, respectively. However, excessive dosage of cellulase had an adverse effect on strength properties in spite of the high beatability. Fibrillization by cellulase and destruction of fiber by excessive reaction was observed by Scanning Electron Microscopy(SEM).

• Fibers and Polymers
• /
• v.7 no.2
• /
• pp.95-104
• /
• 2006

In order to improve the water swelling, thermal/mechanical and adhesion properties of waterborne polyurethane (WBPU), a series of the crosslinkable WBPUs containing hydrophilic ionic component, dimethylol propionic acid (20 mole%), were prepared by in-situ polymerization using a cross-linker hexakis (methoxymethyl) melamine (HMMM). Effects of the HMMM content (2, 4, and 6 wt%) and curing temperature on these properties of the crosslinked WBPUs samples were investigated. All properties were found to increase with increasing HMMM content. It was found that the optimum curing temperature of the WBPU films and adhesives was near $120^{\circ}C$, which was not dependent on the HMMM content.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.4
• /
• pp.289-296
• /
• 2001

The piezoelectric transformers of 2.0x10x48 ㎣ size were fabricated with PSN-PMN-PZT(T10 and PNW-PMN-PZT(T2) composition ceramics. Effects of micro structural and piezoelectric properties on the electrical characteristics of the piezoelectric transformers were investigated. Under the fixed output power of 6 W, temperature rise of T1 transformer at the optimum load was smaller than T2 one because of fine grain size effect. Voltage step-up ratio of T1 transformer showed higher value than T2 one T1 transformer showed an excellent properties with voltage step-up ratio of 12.41, efficiency of 95.23% and temperature rise of 7.2$^{\circ}C$ at 200㏀ load resistance. And also, T2 transformer showed an excellent properties with voltage step up ratio of 9.81, efficiency of 95.51% and temperature rise of 9$^{\circ}C$ at 150㏀ load resistance.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.2891-2894
• /
• 2014

The effects of mechanical activation of carbon black on the processing and properties of butadiene nitrile rubber were studied. Mechanical activation of carbon black caused an improvement in the physical and mechanical properties of the butadiene-nitrile rubber, BNR-18AMN. The optimum activation time that would afford rubber with improved properties was established.

• Macromolecular Research
• /
• v.16 no.7
• /
• pp.596-603
• /
• 2008

To improve the mechanical properties, dimensional stability and blood compatibility, the biomedical material $Pellethene^{(R)}$ was blended with multiblock polyurethane (MPU) containing phospopholipid/long alkyl chain (C-18) at the various MPU contents and crosslinked using dicumyl peroxide as a crosslinking agent. The maximum MPU content for stable $Pellethene^{(R)}$/MPU blended films was approximately 30 wt%. The optimum crosslinking agent content and crosslinking time with respect to the mechanical properties were 4 wt% and 3 h, respectively. The mechanical properties (tensile strength and elongation at break) and water absorption of the crosslinked blend film increased with increasing MPU content. The test of platelet adhesion on the surfaces of the crosslinked blend film showed a decrease in the level of platelet adhesion from 70% to 6% with increasing MPU content from 0 to 30 wt%. These results suggest that the crosslinked $Pellethene^{(R)}$/MPU-30 (MPU content: 30 wt%) sample has strong potential as a novel material for blood compatible material applications.

• Elastomers and Composites
• /
• v.51 no.1
• /
• pp.38-42
• /
• 2016

For improving the heat loss of a refrigerator around door gasket, it is very important to reduce the amount of rubber magnet used, of which thermal conductivity is much higher than the plastics, and enhancing the magnetic properties of rubber magnet itself is crucial for this. In the present study, therefore, a relationship between the optimum conditions of rubber magnet fabrication process and raw material compositions in the ferrite powder/CPE binder compounds was investigated for finding a way to enhance the magnetic properties of rubber magnet. Magnetic attraction forces of a sample rubber magnet was measured as function of distance, and thermal properties of the sample ferrite powder/CPE binder compound were analyzed with TG/DTA thermal analyzer. As a results, a rubber magnet strip with enhanced magnetic properties was expected to be fabricated, of which raw material compound was prepared by compounding with higher ferrite magnetic powder concentration.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.278-284
• /
• 1997

This study dealt with the flowing properties of the super flowing concrete for class F fly ash producted thermal power plant and the application for concrete industry. For this purpose, fly ash is analyzed for confined water ratio($\beta_p$)and the super flowing concrete is tested the flowing properties including flowing velocity, funneling time, height difference of box test and compressive strength. As the result, in order to satisfy the flowing properties of the super flowing concrete using class F fly ash, the optimum mixing conditions are determined water-bindrer ratio 37$\pm$2%, volume ratio of fine aggregates(Sr) 47$\pm$2% and coarse aggregates(Gv) 51$\pm$1%.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.5
• /
• pp.206-206
• /
• 2003

It is hard to expect excellent electrical, mechanical and chemical properties from most of the composite materials presently used as insulators due to insufficient wettability property caused by the difference of interfacial properties between the matrix material and the reinforcer. Therefore, various interfacial coupling agents have been developed to improve the interfacial properties of composite materials. But if the wettable coupling agents are used outdoor for a long time, change in quality takes place in the coupling agents themselves, bringing about deterioration of the properties of the composite materials. In this study, glass surface was treated by plasma to examine the effect of dry interface treatment without coupling agent. It was identified that the optimum parameters for the best wettability of the samples at the time of generation of plasma were oxygen atmosphere, 0.1 torr of system pressure, 100 W of discharge power, and 3 minutes of discharge time. Also, the surface resistance rate and dielectric property were improved.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.5
• /
• pp.206-212
• /
• 2003

It is hard to expect excellent electrical, mechanical and chemical properties from most of the composite materials presently used as insulators due to insufficient wettability property caused by the difference of interfacial properties between the matrix material and the reinforcer. Therefore, various interfacial coupling agents have been developed to improve the interfacial properties of composite materials. But if the wettable coupling agents are used outdoor for a long time, change in quality takes place in the coupling agents themselves, bringing about deterioration of the properties of the composite materials. In this study, glass surface was treated by plasma to examine the effect of dry interface treatment without coupling agent. It was identified that the optimum parameters for the best wettability of the samples at the time of generation of plasma were oxygen atmosphere, 0.1 torr of system pressure, 100 W of discharge power, and 3 minutes of discharge time. Also, the surface resistance rate and dielectric property were improved.