• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.106-112
• /
• 2016

Maleimidopropyltriethoxysilane grafted natural rubber (MISNR) was prepared by reaction of maleic anhydride grafted natural rubber and 3-aminopropyl triethoxysilane. MISNR was used as the compatibilizer of natural rubber/silica composites. The composites were prepared by two-step mixing procedures. The final mixtures were cured with optimum cure condition, which was established by a rheometer. Effects of the amounts of compatibilizer in the composites on the cure characteristics, morphology, thermal stability, and physical and mechanical behaviors were investigated. The composites having MISNR had shown cure characteristics and physical and mechanical properties superior to those without MISNR. Silica particles in the former appeared to be more uniform and reduced in size compared with the latter. The effects of the types of silica were also evaluated.

• Elastomers and Composites
• /
• v.29 no.1
• /
• pp.9-17
• /
• 1994

Methylmetharylate grafted latex(MGL) was prepared by emulsion graft copolymerization of methyl methacrylate onto natural rubber latex(NRL) by using t-butyl hydroperoxide and tetraethylene pentamine in an aqueous medium. Blending of MGL and NRL with different mixing ratio carried out and viscosity and particle size distribution of blend latex were determined. It was found that the optimum condition of mature time, vulcanizing temperature and time for preparation of blend latex films were investigated. latex films prepared by dipping process were meaured. As the reuslt, blend latex(NR-d-MG) films obtained from two-dipping system were more excellent than NR and MG film obtained from one-dipping system.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.1
• /
• pp.69-74
• /
• 2000

Applicability of Thermal field flow fractionation (ThFFF) was investigated for the analysis of masticated natural rubber (NR) adhesives produced bya hot melt mastication process. An optimum ThFFF condition for NR analysis was found by using tetrahydrofuran (THF) as a solvent/carrier and a field-programming. Low flowrate (0.3 mL/min) was used to avoid stopping the flow for the sample relaxation. Measured molecular weight distribution was used to monitor degradation of rubber during the mastication process. Rubber samples collected at three different stages of the mastication process and were analyzed by ThFFF. It was found that in an anaerobic process rubber degradation occurs at the resin-mixing (compounding) zone as well as in the initial break-down zone, while in an aerobic process most of degradation occurs at the initial breakdown zone. It was also found that E-beam radiation on NR causes a slight increase in the NR molecular weight due to the formation of a branched structure.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.374-381
• /
• 2000

Composites of polypropylene (PP) and organically modified montmorillonite (org-MMT) were prepared by melt mixing in an intensive mixer. Three grades of PP's having different melt viscosities were employed to investigate the dispersion characteristics of the composites with various org-MMT's. Depending on the matrix viscosity and nature of the interlayer in org-MMT significant variations of the phase structure were found. Under the constant mixing condition and matrix viscosity, intercalation of PP chains into the interlayer of org-MMT was possible when initial interlayer distance and packing density were maintained in the optimum range; by which the loss in entropy associated with the confinement of polymer chains was compensated. The state of org-MMT particle dispersion was improved by increasing the matrix viscosity only in the case that dispersed phase is suitable for intercalation process thermodynamically, otherwise little variation was occurred regardless of the matrix viscosity. Due to the lack of specific interaction between PP and erg-MMT considered here, although the intercalation was possible for an appropriate org-MMT, the composites revealed unstable phase structure upon increasing the mixing time, which was characterized by agglomeration of the org-MMT domains.

• Environmental Analysis Health and Toxicology
• /
• v.6 no.3_4
• /
• pp.133-141
• /
• 1991

Vermistabilization is the stabilization of organic wastes using earthworms. The worms maintain aerobic conditions in the waste, accelerating and enhancing the biological decomposition of the waste. This study was carried out to find out fundamental factors affecting the performance of the process such as temperature, moisture content and pH condition of nightsoil sludge, and to evaluate the worms excreta (casting) as fertilizer. The results could be summarized as follows; the optimum range of temperature was observed 10~3$0^{\circ}C$ while survival rate of eathworm decreased rapidly at 35$^{\circ}C$ within 6 days and death occurred at 5$^{\circ}C$. Those of moisture content and pH condition were 50~70% and 5~8, respectively. Earthworms were revealed to change the composition of N in nightsoil sludge consisting of$NH_3$-N (71%), $NO_2$-N (2%) and $NO_3$-N (27%) into that $NH_3$-N (24%), $NO_2$-N (1%), $NO_3$-N (75%) in earthworm excreta, respectively The concentrations of NH$_3$and H$_2$S gas in pig manure were reduced by 59.2% and 45.2% in case of mixing pig manure with casting.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.229-232
• /
• 2006

Two novel synthetic route proposed for Hydro-Terminated Poly(EO-ran-THF) and tri-block(PEC-PTHF-PEG) copolymer by cationic ring-opening polymerization of tetrahydrofuran(THF) and ethylene oxide(EO) and just by polymerization of EO on poly-THF, respectively. Polyurethane was synthesized from random and tri-block HTPE using N-100/IPDI mixture as curing agent, and TPB(Triphenylbismuth) as catalyst. The mechanical properties of resultant polyurethane after mixing with various ratio of isocyanate was also investigated. Finally, the post treatment process of HTPE based on amount of catalyst used in the synthesis was studied, to evaluate the optimum curing condition for the polyurethane propellant binder.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.691-697
• /
• 1996

The NR films were prepared with mixing of natural rubber latex(NRL) with various additives, and NR/CR films were prepared by blend ratio of chloroprene rubber latex(CRL). The swelling degree and the mechanical properties of these films were measured according to the procure time. As a result, optimum condition were showed the swelling degree : 80~85%, precure time : 48~60hrs., and tensile strength was reduced but elongation was increased as increasing the blend ratio of CRL. On the mechanical properties of films prepared by different dipping process in these optimum condition, the tensile strength and tear strength of NR/CR films by one dipping process are better than NR-d-CR films by two dipping process. The surface of these films were observed with scanning electron microscopy(SEM). It was found that phase separation was occured as increasing the blend ratio of CRL.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.1
• /
• pp.1-7
• /
• 2014

When processing the biomass by Hydrothermal carbonization (HTC), a slow pyrolysis process, it produces bio-gas, biooil, and biochar. Among these end products, biochar is known for isolating or storing carbon and being used as a soil amendment. In this study, the characteristics of biochar generated by HTC at $250^{\circ}C$ for 1 hour, 2 hours, 3 hours, and 20 hours with synthetic food wastes and wood wastes were analyzed for potential uses in soil contaminated with heavy metals. The yield of biochar (weight %) increased when the ratio of wood wastes increased and showed a decreasing tendency as reaction time increased. Elemental analysis of biochar based on various conditions showed a maximum of 70% carbon (C) content. The carbon content showed an increasing tendency with the increase of wood wastes. Iodine adsorption test was peformed to determine the optimum reaction condition, which was 15% wood waste for mixing ratio and 2 hours for reaction time. Using biochar generated at the optimum condition, its capability of adsorbing heavy metals (Cd, Cu, Pb, Zn, Ni) was evaluated. It was concluded that lead (Pb) was removed efficiently while zinc (Zn) and nickel (Ni) were hardly adsorbed by biochar.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.3
• /
• pp.34-42
• /
• 1997

This study was carried out to investigate the proper cooking conditions of soda-anthraquinone and alkaline sulfite-anthraquinone pulping of rice-straw, and get basic data f9r the use of rice-straw chemical pulp through the test of characteristics and physical properties of pulps made in the various cooking conditions From the experimental results , we can conclude as follows. In the soda-anthraquinone pulping of rice-straw, the optimum cooking conditions were 60 min. at $150^{\circ}C$ in the amount of caustic soda of 20% with the addition of anthraquinone(0.05%). And total yield, Kappa No. and brightness of pulp made in the condition above mentioned were 41.9%, 7.7 and 51.1 respectively. In the alkaline sulfite-anthraquinone pulping of rice-straw, the proper mixing ratio of cooking chemical(caustic soda : sodium sulfite) was 50:50. And the optimum cooking conditions were 60 min. at $150^{\circ}C$ in the amount of cooking chemical of 20% with the addition of anthraquinone(0.05%). At that time, the total yield, Kappa No, and brightness of pulp were 50.1%, 9.1 and 40.2 respectively. As a result, the alkaline sulfite-anthraquinone pulping was superior to the soda-anthraquinone pulping in the aspect of yield, but inferior in the viewpoints of Kappa No. and brightness. For the comparison of qualities of pulps made in the various cooking methods and conditions, the physical properties of four sorts of pulps were tested. As a result, soda-anthraquinone pulps were superior to alkaline sulfite-anthraquinone pulps in the various strengths excluding tear strength and brightness. On the other hand, pulps made in the condition of addition of cooking chemical of 20% were superior to pulps in the dosage of 15% in the aspects of all the strengths and brightness.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.10
• /
• pp.1039-1046
• /
• 2008

The combining process of UV irradiation and H$_2$O$_2$ was used to investigate characteristics of cefaclor decomposition in the aquatic environment. The separate mixing tank was used to minimize the decreasing effective of contact area caused by sampling. Four baffles were installed inside the UV reactor for the complete mixing of the sample and outside of the reactor was wrapped with aluminum foil to protect the emission of photon energy. Production of OH radical was measured using pCBA(p-Chlorobenzoic acid) indirectly and rate constants were withdrawn pseudo-frist order reaction. Optimum condition for the maximum production of OH radical was found to be pH 3, hydrogen peroxide of 5 mmol/L and recirculation rate of 400 mL/min. Pseudo-frist order reaction rate constant was 0.1051 min$^{-1}$. In the optimum condition, cefaclor was completely decomposed within 40 min and rate constant was 0.093 min$^{-1}$. Decomposition by OH radical producted intermediate anions such as chloride, nitrate, sulfite and acetic acid and phenylglycine. After 6 hr most cefaclor was decomposed by UV/H$_2$O$_2$ process and converted to CO$_2$ and H$_2$O, resulting of operation in the decrease of TOC and acetic acid and the disappearance of phenylglycine.