• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1185-1192
• /
• 2012

The typical operating temperature of an automotive fuel cell is lower than that of an internal combustion engine, which necessitates a refined strategy for thermal management. In particular, the performance of the cooling module has to be higher for a fuel cell system because the temperature difference between the fuel cell and the surrounding is lower than in the case of the internal combustion engine. Even though the cooling system of an automotive fuel cell determines the operating temperature and temperature distribution of the fuel cell, it has attracted little research attention. This study presents the mathematical model of a cooling system for an automotive fuel cell system using Matlab/$Simulink^{(R)}$. In particular, a radiator model is developed for design optimization from the development stage to the operating stage for an automotive fuel cell. The cooling system model comprises a fan, pump, and radiator. The pump and fan model have an empirical relation, and the dynamics of the pump and fan are only explained by motor dynamics. The basic design study was conducted, and the geometric setup of the radiator was investigated. When the control logic was applied, the pump senses the coolant inlet temperature and the fan senses the coolant out temperature. Additionally, the cooling module is integrated with the fuel cell system model so that the performance of the cooling module can be investigated under realistic operating conditions.

• Journal of Korea Water Resources Association
• /
• v.46 no.9
• /
• pp.933-946
• /
• 2013

The quantitative analysis of evapotranspiration (ET) is a key component in hydrological studies and the establishment of water resources planning. Generally, the quantitative analysis of ET is performed by the estimation method of potential or reference ET based on meteorological factors such as air temperature, wind speed, etc. Hargreaves equation is one of empirical methods for reference ET using air temperature data. In this study, in order to estimate more exact reference ET considering climatological characteristics in Korea, parameter regionalization of Hargreaves equation is carried out. Firstly, modified Hargreaves equation is presented after the analysis of the relationship between solar radiation and temperature. Secondly, parameter ($K_{ET}$) optimization of Hargreaves equation is performed using Penman-Monteith method and modified equation at 71 weather stations. Lastly, the equation for calculating $K_{ET}$ using temperature data is proposed and verified. As a result, reference ET from original Hargreaves equation is overestimated or underestimated compared with Penman-Monteith method. But modified equation in this study is more accurate in the climatic conditions of Korea. In addition, the applicability of the equation between $K_{ET}$ and temperature is confirmed.

• Korean Journal of Microbiology
• /
• v.38 no.4
• /
• pp.312-317
• /
• 2002

Erythritol is of interest as a low calorie sweetner. Penicillium sp. KJ8l was screened for erythritol producer in nature. The effect of culture conditions on erythritol production by Penicillium sp. KJ81 was examined. This strain produced about 12 g/l erythritol and a small amout of glycerol. Erythritol was not produced from mannitol, arabinose, sorbitol, and xylose but from glucose, sucrose, fructose, mannose, lactose, maltose, and galactose. This strain was able to produce erythritol in a medium containing 60% sucrose but demonstrated the highest productivity of erythritol in a 30% sucrose medium. The highest yield in Penicillium sp. KJ8l was obtained when 0.5% ammonium sulfate was added to the medium containing 30% sucrose and 0.5% yeast extract. Penicillium sp. KJ81 produced 28.2 g/l erythritol when this strain was cultured in the medium containing 30% sucrose, 0.5% yeast extract, 0.5%$(NH_{4})_{2}SO_{4}$ 0.1% $KH_{2}PO_{4}$ and 0.01% $MgCl_{2}$ under the condition of 1 vvm aeration and 200 rpm agitation at $37^{\circ}C$ for 10 days in 5ι jar fermentor.

• Korean Chemical Engineering Research
• /
• v.55 no.4
• /
• pp.542-547
• /
• 2017

Ultrasound-assisted extraction (UAE) has attracted growing interest, as it is an effective method for the rapid extraction of bioactive compounds from plants with a high extraction efficiency comparable to the conventional extraction. In this study, UAE was used for the extraction of polyphenols from lipid extracted microalgae (Tetraselmis KCTC 12236BP) and the effects of five extraction variables on the total phenolic compounds (TPC) were studied. For the optimization of extraction parameters, particle size, solid-to-liquid (L/S) ratio, ethanol concentration, extraction temperature and extraction time have been examined as independent variables. All variables exhibited the significant effects on the extraction of TPC and extraction temperature showed the most significant effect among five variables. The optimal extraction conditions were the extraction using mixed particle, S/L ratio of 10%, ethanol concentration of 60%, extraction temperature of $100^{\circ}C$ and extraction time of 30 min, which gave the 8.7 mg GAE/g DW for TPC. Compared with conventional hot-water extraction, TPC extraction under UAE was increased by up to 1.8 fold with same extraction condition. This study showed that UAE under low temperature and short extraction time was proven to be an effective extraction process for TPC production from LEA compared to conventional hot-water extraction process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.27-36
• /
• 2019

The demand for a low dispersion lens with a small refractive index and a high refractive index is increasing, and accordingly, there is an increasing need for a releasable protective film with high heat resistance and abrasion resistance. On the other hand, the optical industry has not yet established a clear standard for the manufacturing process and quality standards for mold-releasing protective films used in aspheric glass lens molding. Optical lens manufacturers treat this technology as proprietary information. In this study, an experiment was conducted regarding the optimization of ion etching, magnetron, and arc current at each source and filter part, and bias voltage in FCVA (filtered cathode vacuum arc)-based Ta-C thin film coatings. This study found that compared to iridium-rhenium alloy thin film sputtering products, the coating conditions were improved by approximately 50%, 20%, and 40% in terms of thickness, hardness, and adhesive strength of the film, respectively. The thin-film coating process proposed in this study is expected to contribute significantly to the development and utilization of glass lenses, which will help enhance the minimum mechanical properties and quality of the mold-release thin film layer required for glass mold surface forming technology.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.26 no.1
• /
• pp.1-8
• /
• 2016

The Korea Meteorological Administration has operated the Automatic Weather Stations, of the average 13 km horizontal resolution, to observe rainfall. However, an additional RADAR network also has been operated in all-weather conditions, because AWS network could not observed rainfall over the sea. In general, the rain rate is obtained by estimating the relationship between the radar reflectivity (Z) and the rainfall (R). But this empirical relationship needs to be optimized on the rainfall over the Korean peninsula. This study was carried out to optimize the Z-R relationship in the summer of 2014 using a parallel Micro Genetic Algorithm. The optimized Z-R relationship, $Z=120R^{1.56}$, using a micro genetic algorithm was different from the various Z-R relationships that have been previously used. However, the landscape of the fitness function found in this study looked like a flat plateau. So there was a limit to the fine estimation including the complex development and decay processes of precipitation between the ground and an altitude of 1.5km.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.171-178
• /
• 2014

From now on, in order to meet more stringer diesel emission standard, diesel vehicle should be equipped with emission after-treatment devices as NOx reduction catalyst and particulate filters. Urea-SCR is being developed as the most efficient method of reducing NOx emissions in the after-treatment devices of diesel engines, and recent studies have begun to mount the urea-SCR device for diesel passenger cars and light duty vehicles. That is because their operational characteristics are quite different from heavy duty vehicles, urea solution injection should be changed with other conditions. Therefore, the number and diameter of the nozzle, injection directions, mounting positions in front of the catalytic converter are important design factors. In this study, major design parameters concerning urea solution injection in front of SCR are optimized by using a CFD analysis and Taguchi method. The computational prediction of internal flow and spray characteristics in front of SCR was carried out by using STAR-CCM+7.06 code that used to evaluate $NH_3$ uniformity index($NH_3$ UI). The design parameters are optimized by using the $L_{16}$ orthogonal array and small-the-better characteristics of the Taguchi method. As a result, the optimal values are confirmed to be valid in 95% confidence and 5% significance level through analysis of variance(ANOVA). The compared maximize $NH_3$ UI and activation time($NH_3$ UI 0.82) are numerically confirmed that the optimal model provides better conversion efficiency of $NH_3$. In addition, we propose a method to minimize wall-wetting around the urea injector in order to prevent injector blocks caused by solid urea loading. Consequently, the thickness reduction of fluid film in front of mixer is numerically confirmed through the mounting mixer and correcting injection direction by using the trial and error method.

• Microbiology and Biotechnology Letters
• /
• v.26 no.1
• /
• pp.15-22
• /
• 1998

The dnrF gene, responsible for conversion of aklavinone to $\varepsilon$-rhodomycinone via C-11 hydroxylation, was mapped in the daunorubicin gene cluster of Streptomyces peucetius subsp. caesius ATCC 27952, close to drrAB, one of the anthracycline resistance genes. To characterize the enzymatic properties of the aklavinone 11-hydroxylase, the dnrF gene was overexpressed in Escherchia coli. The pET-22(+) plasmid which has the T7 promoter under the control of lacUV5 gene was used for the overexpression of the dnrF gene, and the recombinant plasmid pET213 that contains the dnrF gene linked to the T7 promoter of pET-22b(+) was introduced into the E. coli BL2l. When the expression of the dnrF gene was induced by IPTG at the final concentration of 1 mM, the induced protein could be detected in SDS-PAGE only in insoluble precipitate. The insoluble protein was electroeluted from the gel and used for the preparation of antiserum in mice. Various culture conditions were tested to maximize the expression of the aklavinone 11-hydroxylase in soluble form. The enzymatic activity was checked by the bioconversion experiment, and the protein was confirmed by the SDS-PAGE and the Western blot analysis. From the analysis of the data, it was concluded that the culture induced with IPTG at the final concentration of 0.02 mM at 37$^{\circ}C$ yielded the best productivity of active form of enzyme.

• Journal of Astronomy and Space Sciences
• /
• v.22 no.4
• /
• pp.451-462
• /
• 2005

Optimal Trajectory Correction Maneuver (TCM) design algorithm has been developed using the B-plane targeting method for future Korean Mars missions. For every-mission phase, trajectory informations can also be obtained using this developed algorithms which are essential to design optimal TCM strategy. The information were computed under minimum requiring perturbations to design Mars missions. Spacecraft can not be reached at designed aim point because of unexpected trajectory errors, caused by many perturbations and errors due to operating impulsive maneuvers during the cruising phase of missions. To maintain spacecraft's appropriate trajectory and deliver it to the designed aim point, B-plane targeting techniques are needed. A software NPSOL is used to solve this optimization problem, with the performance index of minimizing total amount of TCM's magnitude. And also executing time of maneuvers on be controlled for the user defined maneuver number $(1\~5)$ of TCMs. The constraints, the Mars arrival B-plane boundary conditions, are formulated for the problem. Results of this work show the ability to design and analyze overall Mars missions, from the Earth launch phase to Mars arrival phase including capture orbit status for future Korean Mars missions

• Journal of Korean Society of Steel Construction
• /
• v.19 no.1
• /
• pp.15-27
• /
• 2007

Over the past decade, labor costs have increased relative to the cost of material hardware according to analysts in the construction industry. Therefore, the minimum weight design, which has been widely adopted in the literature for the optimal design of steel structures, is no longer the most economical construction approach. Presently, although connection- related costs is crucial in determining the most cost-effective steel structures, most studies on this subject focused on minimum-weight design or engaged in higher analysis. Therefore, in this study, we proposed a fabrication scheme for the most cost-effective moment-resisting steel frame structures that resist lateral loads without compromising overall stability. The proposed approach considers the cost of steel products, fabrication, and connections within the design process. The optimal design considered construction realities, with the optimal trade-off between the number of moment connections and total cost was achieved by reducing the number of moment connections and rearranging them using the combination of analysis that includes shear, displacement and interaction value based on the LRFD code and optimization scheme based on genetic algorithms. In this study, we have shown the applicability and efficiency in the examples that considered actual loading conditions.