• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.1
• /
• pp.106-113
• /
• 2013

One of feasible non-destructivity test methods for evaluation of concrete permeability is the measurement of surface resistivity. But the application to steel fiber-reinforced concrete has been limited because mis-evaluation could be caused by the steel fibers in concrete. In this study, the effect of fiber distribution on surface electrical resistivity of steel fiber-reinforced concrete was investigated through experimental program. Resistivity was measured three times on four surfaces in three rectangular and circular specimens with 0.5%, 1% and 1.5% steel fibers by volume and compared each other. The results obtained from circular specimens were consistent compared to those from rectangular specimens. And the results demonstrated that the effect of fiber distribution on surface resistivity was not significant compared to that of mixing ratio of steel fibers. In conclusion, this non-destructive testing method using measurement of surface resistivity could be used for SFRC within 0.5% steel fibers by volume.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.72-77
• /
• 2008

This paper investgated on fabrication process and tolerance of resistance body with a uniform thickness formed by the process of cavity type on organic substrate for application of embedded resistor. To improve the tolerance of resistance value according to a position of PCB cause by conventional screen printing, we introduced the process of cavity type from organic substrate. A resistor with a desired shape and volume was precisely formed by the process of cavity using a resistor paste and screen printing. This method can increase PCB's productivity by shortening its production time because process conditions of a screen prining device can be set quickly without any affection on its position accuracy.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.2 s.20
• /
• pp.115-121
• /
• 2006

In recent years vibration control damper made of low yield point steel is expected to play an important role in controlling structural vibration induced earthquake and wind. But their dynamic characteristics and energy dissipation effects on the whole structure model are not clarified. In this paper, firstly, we presents the results of cyclic tests on low yield steel dampers. Secondly, forced vibration tests on existence three stories steel structure model with low yield point steel dampers are presented. Lastly, it is estimated energy amount which is dissipated through the hysteresis dampers by using two types of analytical models, hysteresis model and equivalent linear model.

• Applied Biological Chemistry
• /
• v.40 no.6
• /
• pp.508-513
• /
• 1997

Thermal characteristics and granular morphology on enzyme-resistant starches (RS) formed during heat-moisture treatment (HMT) and retrogradation were investigated in high amylose corn starches, Hylon V and Hylon VII. With each treatment, both starches showed a similar trend in the increase of RS, but RS yield of Hylon VII is higher than that of Hylon V. Specially, RS was increased remarkably by HMT. It was more than doubled from 11.4% to 26.6% for Hylon V and from 15.9% to 32.8% for Hylon VII. A small increase of RS resulted from retrogradation. HMT on starch increased gelatinization temperature, decreased enthalpy. Retrograded starch exhibited small three endothermic transitions at $94^{\circ}C$, $110^{\circ}C$ and $140^{\circ}C$ in differential scanning calorimetry (DSC) thermogram due to the remained ungelatinized starch granules, dissociation of amylose-lipid complex and melting of recrystallized amylose, respectively. Enzyme-resistant starches isolated from native and heat-moisture treated starches showed a broad endothermic transition at higher temperature than native starch, while retrograded starch exhibited a very sharp peak at ${\sim}150^{\circ}C$ due to the melting of amylose crystallites. Under microscopy, starch granules with HMT was not changed, but retrograded starches showed the aggregates of starch granules because amylose leached out during gelatinization. Iodine stained RS clearly showed the differences in enzyme hydrolysis on the native, heat-moisture treated and retrograded starches.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.291-298
• /
• 2006

Resistivity method is a practical and effective geophysical technique to detect leakage zones in embankment dams. Generally, resistivity survey conducted along the crest assumes that the embankment dam has a 2D structure. However, the 3D topography of embankments distorts significantly resistivity data measured on anywhere of the dam. In this study, we analyse the influence from 3D effects created by specific dam geometry through the 3D finite element modeling technique. We compared 3D effects when resistivity surveys are carried out on the upstream slope, left edge of the crest, center of the crest, right edge of the crest and downstream slope. We ensure that 3D effect is greatly different according to the location of the survey line and data obtained on the downstream slope are most greatly influenced by 3D dam geometry. Also, resistivity data are more influenced by the electrical resistivity of materials constituting reservoir than 3D effects due to specific dam geometry. Furthermore, using resistivity data synthesized with 3D modeling program for an embankment dam model with leakage zone, we analyse the possibility of leakages detection from 2D resistivity surveys performed along the embankment dam.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2C
• /
• pp.85-93
• /
• 2010

The shear stiffness has become an important design parameter to understand the soil behavior. In particular, the elastic moduli and void ratio has been considered as important parameters for the design of the geotechnical structures. The objective of this paper is the development of the penetration type Field Velocity and Resistivity Probe (FVRP) which is able to assess the elastic moduli and void ratio based on the elastic wave velocities and electrical resistivity. The elastic waves including the compressional and shear wave are measured by piezo disk elements and bender elements. And the electrical resistivity is measured by the resistivity probe, which is manufactured and installed at the tip of the FVRP. The penetration tests are carried out in calibration chamber and field. In the laboratory calibration chamber test, after the sand-clay slurry mixtures are prepared and consolidated. The FVRP is progressively penetrated and the data are measured at each 1 cm. The field experiment is also carried out in the southern part of Korea Peninsular. Data gathering is performed in the depth of 6~20 m at each 10 cm. The elastic moduli and void ratio are estimated based on the analytical and empirical solutions by using the elastic wave velocities and electrical resistivity measured in the chamber and field. The void ratios based on the elastic wave velocities and the electrical resistivity are similar to the volume based void ratio. This study suggests that the FVRP, which evaluates the elastic wave velocities and the electrical resistivity, may be a useful instrument for assessing the elastic moduli and void ratio in soft soils.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.275-278
• /
• 2000

We were fabricated of NiCr thin film resistors(TFR) on A1$_2$O$_3$(99.5%) substrates by dc magnetic sputtering system. The characteristics of electrical resistance (Sheet resistance & Temperature-Coefficient of the resistance-value:TCR) by annealing condition and reactive gas on the resistors were studied.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.3-12
• /
• 1967

This study has been endeavored to deposit resistance films of tin oxide on the cylindrical Pyrex glass rods. In this report, at first an outline of the film formation is described and later some electrical properities of the resistance films manufactured through new method is discussed in detail. Because the new method which is called, "Chemical Vapour Reaction Process", is not only easy to get stable resistance films, but also doesn't need vacuum systtem, it seems to be a promising fundamental process to go into flow system mass production. Electrical properties of resistance films made by the new mathod are similar to or surpassing those by provious method (for example splay method). The top data thus obtained shows that surface resistivity is 25ohm/sq. with 12 ppm in temperature coefficient of resistor. resistor.

• The Journal of Society for e-Business Studies
• /
• v.15 no.2
• /
• pp.205-217
• /
• 2010

IPTV Service was launched with great expectation, but it is having difficulty due to the low number of subscribers and contents. In addition, the study of IPTV is still in its infancy and most of previous studies are only focused how IPTV is adopted and spread. In this study, we defined that resistance is the users not tend to accept IPTV service, and analyzed factors affecting resistance which are Innovative characteristics, User characteristics, Service characteristics and proposed implications for IPTV service vitalization. The results that relative advantage, complexity, attitude of an existing product, contents, cost, innovativeness have significant effects on resistance to IPTV.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.45-50
• /
• 1999

Copper has been widely used for the electronic parts, and especially spot welded one for the leads of condenser or resistor. However, copper is generally hard to be spot welded because of its low electrical resistivity. For this experiment, Sn-37%Pb solder which has relatively higher resistivity was coated on the Cu-sheet to improve the spot weldability of copper. As the experimental variables welding pressure was varied from 100 to 200kgf, welding time from 20 to 50ms, and welding current from 100 to 2500A. Experimental results showed that the solder coated Cu-sheet can be spot welded under the conditions of 400~2200A welding current, 100~200kgf pressure and 20-50ms welding time. The tensile shear strength of the spot welded joint increased with welding current up to the critical current, and after the critical value decreased with current.