• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.43-49
• /
• 2002

Pd/Ge/Pd/Ti/Au ohmic contact to n-type InGaAs was investigated with rapid thermal annealing conditions. Minimum specific contact resistivity of $1.1\times10^{-6}\Omega\textrm{cm}^2$ was achieved after annealing at $400^{\circ}C$/10sec, and a ohmic performance was degraded at higher annealing temperature due to the chemical reaction between the ohmic contact materials and the InGaAs substrate. However, non-spiking planar interface and relatively good ohmic contact($high-10^{-6};{\Omega}\textrm{cm}^2$) were maintained. This ohmic contact system is expected to be a promising candidate for compound semiconductor devices.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.417-420
• /
• 2009

This study develops a highly transparent ohmic contact using phosphorus doped ZnO with current spreading for p-GaN to increase the optical output power of nitride-based light-emitting diodes (LEDs). The phosphorus doped ZnO transparent ohmic contact layer was prepared by radio frequency magnetron sputtering with post-deposition annealing. The transmittance of the phosphorus doped ZnO exceeds 90% in the region of 440 nm to 500 nm. The specific contact resistance of the phosphorus doped ZnO on p-GaN was determined to be $7.82{\times}10^{-3}{\Omega}{\cdot}cm^2$ after annealing at $700^{\circ}C$. GaN LED chips with dimensions of $300\times300{\mu}m$ fabricated with the phosphorus doped ZnO transparent ohmic contact were developed and produced a 2.7 V increase in forward voltage under a nominal forward current of 20 mA compared to GaN LED with Ni/Au Ohmic contact. However, the output power increased by 25% at the injection current of 20 mA compared to GaN LED with the Ni/Au contact scheme.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.208-209
• /
• 2008

Ni/Ti/Al multilayer system was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Compared with conventional process using Ni, Ni/Ti/Al contact shows perfect ohmic behavior, and possesses much lower contact resistance of about $2.5\times10^{-4}\Omega{\cdot}cm^2$ after $930^{\circ}C$ RTA, which is about 2 orders of magnitude smaller than that of Ni contact. Contact resistance gradually increased as the RTA temperature was lowered in the range of 840 ~ $930^{\circ}C$, and about $3.4\times10^{-4}\Omega{\cdot}cm^2$ was obtained at the lowest RTA temperature of $840^{\circ}C$. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance.

• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.131-135
• /
• 2005

This paper describes the ohmic contact formation of single crystalline 3C-SiC thin films heteroepitaxially grown on Si(001) wafers. In this work, a TiW (Titanium-tungsten) film as a contact matieral was deposited by RF magnetron sputter and annealed with the vacuum and RTA (rapid thermal anneal) process respectively. Contact resistivities between the TiW film and the n-type 3C-SiC substrate were measured by the C-TLM (circular transmission line model) method. The contact phases and interface the TiW/3C-SiC were evaulated with XRD (X-ray diffraction), SEM (scanning electron microscope) and AES (Auger electron spectroscopy) depth-profiles, respectively. The TiW film annealed at $1000^{\circ}C$ for 45 sec with the RTA play am important role in formation of ohmic contact with the 3C-SiC substrate and the contact resistance is less than $4.62{\times}10^{-4}{\Omega}{\cdot}cm^{2}$. Moreover, the inter-diffusion at TiW/3C-SiC interface was not generated during before and after annealing, and kept stable state. Therefore, the ohmic contact formation technology of single crystalline 3C-SiC using the TiW film is very suitable for high temperature MEMS applications.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.21-28
• /
• 2000

Refractory metals, W and Ti, and their nitrides, $W_2N$ and TiN, were investigated for using as an ohmic contact material with SiC single crystalline thin films. The possibility of nitride materials for using as a stable ohmic contact material of SiC at high temperatures was examined by considering the thermal stability depending on the heat treatment temperature, their electrical properties and protective behavior from the interdiffusion. W contact with SiC thin films, deposited by using new organosilicon precursor, bis-trimethylsilylmethane, showed the lowest resistivity, $2.17{\times}10^{-5}$Ω$\textrm{cm}^2$. On the other hand, Ti-based contact materials showed higher contact resistivity than W-based ones. The oxidation of contact materials was restricted by applying Pt thin films on those electrodes. Nitride electrodes had rather stable electrical properties and better protective behavior from interdiffusion than metal electrodes.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.2
• /
• pp.129-138
• /
• 2011

Performance changes of an anode-supported tubular SOFC including current collectors are analyzed at different current collecting methods using numerical simulation. From the two dimensional numerical model of the solid oxide fuel cell with nickel felts as anodic current collectors and silver wires as cathodic ones, the performance curves and the distributions of temperature, concentration, current density are obtained. Also, the voltage loss of the cell is divided into three parts: activation loss, concentration loss and ohmic loss. The results show that the performance change of the cell is dominantly influenced by the ohmic loss. Although the temperature and concentration distributions are different, the total activation loss and concentration loss are nearly same. And the ohmic loss is divided into each parts of the cell components. The ohmic loss of the anodic current collectorreaches about 60~80% of the cell's total ohmic loss. Therefore, the reduction of the ohmic loss of the anodic current collector is very important for stack power enhancement. It is also recommended that the load should be connected to the both ends of the anodic current collector.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.567-571
• /
• 2003

We investigate vanadium (V)-based Ohmic contacts on n-GaN ($N_{d}$=$2.0${\times}$10^{18}$ $cm^{-3}$ ) as a function of annealing temperature. It is shown that the V (60 nm) contacts become Ohmic with specific contact resistances of $10^{-3}$ $- 10^{-4}$ Ω$\textrm{cm}^2$ upon annealing at 650 and $850^{\circ}C$. The V(20 nm)/Ti(60 nm)/Au(20 nm)contacts produce very low specific contact resistances of $2.2 ${\times}$ 10^{-5}$ and$ 4.0${\times}$10^{-6}$ Ω$\textrm{cm}^2$ when annealed at 650 and $850{\circ}C$, respectively. A comparison shows that the use of the overlayers (Ti/Au) is very effective in improving Ohmic property. Based on the current-voltage measurement, Auger electron spectroscopy, glancing angle X-ray diffraction, and X-ray photoemission spectroscopy results, the possible mechanisms for the annealing temperature dependence of the Ohmic behavior of the V-based contacts are described and discussed.d.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.4
• /
• pp.357-362
• /
• 2010

Electricity can be directly generated from organic matter even wastewaters using a microbial fuel cell. To achieve high power in MFCs, finding factors decreasing activation and Ohmic losses is very important. In this study we determined activation loss at the anode and cathode and Ohmic loss using the current interruption technique in a H-type MFC. Activation loss at the cathode was four times higher that that of anode activation loss even if pt-coated carbon (0.5 $mg/cm^2$;10%Pt) was used as the cathode. Ohmic loss determined using current interruption technique (1146 ${\Omega}$) was almost same as the internal resistance (1167 ${\Omega}$) measured using AC impedance. The sum of activation losses at the anode and cathode was the same as the value of activation loss of the cell.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.125-128
• /
• 2017

This study is on how ohmic area etching affects the buffer breakdown voltage of AlGaN/GaN HEMT. The surface morphology of the ohmic metal can be improved by whole etching on the ohmic area. The buffer breakdown voltages of the samples with whole etching on the ohmic area were improved by the suppression of the metal spikes formed under the ohmic contact regions during high-temperature annealing. The samples with selective etching on the ohmic area were investigated for comparison. In addition, the buffer leakage currents were measured on the different radii of the wafer, and the uniformity of the buffer leakage currents on the wafer were investigated by PL mapping measurement.