• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.1
• /
• pp.6-12
• /
• 2007

In this paper, an robust adaptive backstepping controller is proposed for the speed control of separately excited DC motor in pure electric vehicles. A general electric drive train of PEV is conceptually rearrange to major subsystems as electric propulsion, energy source, and auxiliary subsystem and the load torque is modeled by considering the aerodynamic, rolling resistance and grading resistance. Armature and field resistance, damping coefficient and load torque are considered as uncertainties and noise generated at applying load torque to motor is also considered. It shows that the backstepping algorithm can be used to solve the problems of nonlinear system very well and robust controller can be designed without the variation of adaptive law. Simulation results are provided to demonstrate the effectiveness of the proposed controller.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.628-634
• /
• 2005

From AC analysis results utilizing a 2-dimensional device simulator, we extracted an AC-equivalent circuit of a grounded-gate NMOS (ggNMOS) electrostatic discharge (ESD) protection device. The extracted equivalent circuit is utilized to analyze the effects of the parasitics in a ggNMOS protection device on the characteristics of a low noise amplifier (LNA). We have shown that the effects of the parasitics can appear exaggerated for an impedance matching aspect and that the noise contribution of the parasitic resistances cannot be counted if the ggNMOS protection device is modeled by a single capacitor, as in prior publications. We have confirmed that the major changes in the characteristics of an LNA when connecting an NMOS protection device at the input are reduction of the power gain and degradation of the noise performance. We have also shown that the performance degradation worsens as the substrate resistance is reduced, which could not be detected if a single capacitor model is used.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2835-2838
• /
• 2003

We study the characteristics of oscillating in non-autonomous condition and the conducted noise generation in a RL-photocoupler circuit. This circuit may be shown a period-doubling and a chaos dynamics under any specific conditions of input circuit. But, the relationship between input signals and output signals is different according to the amplitude of driving input voltage. Then, the oscillation noise was analyzed with respect to both the frequency and the amplitude of an external ac signal and do values. The results show that the noise-induced oscillations for falling and rising cycles induced by kick-back effect in an inductor, nonlinear capacitance, nonlinear resistance and charge storage time in a diode and an LED. We also compared the simulation with the experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.517-521
• /
• 2001

Measurement techniques for the in-duct source characteristics of fluid machines can be classified into direct method and load method, according to whether the technique employs an external acoustic source or not. It has been known that the two methods yield different results and the load method used to come up with a negative source resistance, in spite of the fact that a very accurate prediction of radiated noise can be obtained by using any result. This paper is focused to the effect of time-varying nature of fluid machines on the output result. For this purpose, a simplified fluid machine consisting of a reservoir, a valve and a pipe is considered as representing a typical linear, periodic, time-varying system and the measurement techniques are simulated by utilizing the Hill equation and its steady-state forced response. In the load method, the source impedance turns out being dependent on the valve impedance at the calculation frequency and the valve and load impedances at other frequencies as well.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.35-39
• /
• 2000

Large-area high-temperature superconducting (HTS) films, filter design and damage-free processing technique have been developed to fabricate low insertion loss and sharp skirt filters. Further, long life cryocooler, low temperature low noise amplifier (LNA) and cryocable have been developed to assemble HTS filter subsystem for IS-95 and IMT-2000 mobile telecommunication. The surface resistance of the films was about 0.2 milli-ohm at 70 K, 12 GHz. An 11-pole HTS filter for IS-95 telecommunication system and a 16-pole HTS filter for IMT-2000 telecommunication system were designed and fabricated using 60 {\times}$ 50 mm$^2$ and one half of 3-inch diameter YBCO films on a 0.5-mm-thick MgO substrate, respectively. We have assembled the filter and low temperature LNA in a dewar with the cryocooler. Ultra low-noise (noise figure: 0.5 dB at 70 K) and ultra sharp-skirt (40 dB/1.5 MHz) performance was presented by the IS-95 filter subsystem and the IMT-2000 filter subsystem, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.5 no.1
• /
• pp.40-43
• /
• 1980

The Service area in AM Broadcast Changes according to its transmitting frequency. It is also reduced by increase of the citizen noise. As a result, the efficency of transmitting Antenna should be higer in a low noise region as long as AM Broadcast does not build up its transmitting power. The efficiency of transmitting Antenna can also function as a low resistance connection to earth. Most Vertical Antenna used in the AM standard Broadcast band in the Korea have extensive radial ground systems beneath them which serve as image plane.

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.122-126
• /
• 2012

Steel lining board usually is used as a floor on the temporary steel bridges. It also is installed in the subway construction site. However, in particular in subway construction, renovations and site of old bridges, these steel lining board structures have a problem such as noise, accidents and slip hazards. So steel composite lining board is being developed to solve this problem. Steel composite lining board consists of compressive concrete showing excellent performance in slip, durability, resistance and noise, lower tensile and shear steel showing high safety, effective and superior workability in many respects. Steel composite lining board structure gradually is used in many construction sites, because it has a high quality such as durability, little noise and slip. In this study, flexural tests of steel composite lining board in accordance with welding patterns were conducted to compare the performance of the structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.268-270
• /
• 2013

It is well known that tire pattern design factors have a large influence on overall tire performance. In this paper, the basic study on the effects of tire pattern design factors on tire labeling performance has been carried out through experimental tests. The pass-by noise is affected by tire pattern design, by a maximum of 2.7dB(A), and the number of sipes gives large effects on PBN. The rolling resistance is also influenced, mostly by the number of longitudinal grooves and secondly the number of sipes. Finally, there is a weak correlation between PBN and RR when the pattern design factors are changed.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.475-482
• /
• 2022

Signal pre-processing and post-processing are some areas of study around electrical resistance tomography due to the low spatial resolution of pixel-based reconstructed images. In addition, methods that improve integrity and noise reduction are candidates for application in ERT. Lately, formulations of image processing methods provide new implementations and studies to improve the response against noise. For example, compact variational mode decomposition has recently shown good performance in image decomposition and segmentation. The results from this first approach of C-VMD to ERT show an improvement due to image segmentation, providing filtering of noise in the background and location of the target.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.2 s.314
• /
• pp.55-62
• /
• 2007

This paper proposes method to get exquisite third dimension data removing included noise by error that occur in third dimension reconstruction through camera auto-calibration. Though reconstructing third dimension data by previous noise removing method, mesh that area is wide is happened problem by noise. Because mesh's area is important, the proposed algorithm need preprocessing that remove unnecessary triangle meshes of acquired third dimension data. The research analyzes the characteristics of noise using the area information of 3-dimensional meshes, separates a peek noise and a Gauss noise by its characteristics and removes the noise effectively. We give a quantitative evaluation of the proposed preprocessing filter and compare with the mesh smoothing procedures. We demonstrate that our effective preprocessing filter outperform the mesh smoothing procedures in terms of accuracy and resistance to over-smoothing.