• Bulletin of the Korean Chemical Society
• /
• v.26 no.11
• /
• pp.1749-1756
• /
• 2005

The $NiSO_4$ supported on FeO-promoted $ZrO_2$ catalysts were prepared by the impregnation method. FeOpromoted $ZrO_2$ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. The addition of nickel sulfate (or FeO) to $ZrO_2$ shifted the phase transition of $ZrO_2$ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or FeO) and $ZrO_2$. 10-$NiSO_4$/5-FeO-$ZrO_2$ containing 10 wt % $NiSO_4$ and 5 mol % FeO, and calcined at 500 ${^{\circ}C}$ exhibited a maximum catalytic activity for ethylene dimerization. $NiSO_4$/FeO-$ZrO_2$ catalysts was very effective for ethylene dimerization even at room temperature, but FeO-$ZrO_2$ without $NiSO_4$ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of FeO up to 5 mol % enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between FeO and $ZrO_2$ and due to consequent formation of Fe-O-Zr bond.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.402.1-402.1
• /
• 2016

The performance of solid oxide fuel cells (SOFCs) is directly related to the electrocatalytic activity of composite electrodes in which triple phase boundaries (TPBs) of metallic catalyst, oxygen ion conducting support, and gas should be three-dimensionally maximized. The distribution morphology of catalytic nanoparticle dispersed on external surfaces is of key importance for maximized TPBs. Herein in situ grown nickel nanoparticle onto the surface of fluorite oxide is demonstrated employing gadolium-nickel co-doped ceria ($Gd0.2-xNixCe0.8O2-{\delta}$, GNDC) by reductive annealing. GNDC powders were synthesized via a Pechini-type sol-gel process while maximum doping ratio of Ni into the cerium oxide was defined by X-ray diffraction. Subsequently, NiO-GNDC composite were screen printed on the both sides of yttrium-stabilized zirconia (YSZ) pellet to fabricate the symmetrical half cells. Electrochemical impedance spectroscopy (EIS) showed that the polarization resistance was decreased when it was compared to conventional Ni-GDC anode and this effect became greater at lower temperature. Ex situ microstructural analysis using scanning electron microscopy after the reductive annealing exhibited the exsolution of Ni nanoparticles on the fluorite phases. The influence of Ni contents in GNDC on polarization characteristics of anodes were examined by EIS under H2/H2O atmosphere. Finally, the addition of optimized GNDC into the anode functional layer (AFL) dramatically enhanced cell performance of anode-supported coin cells.

• Resources Recycling
• /
• v.30 no.3
• /
• pp.18-29
• /
• 2021

Platinum group metals (PGMs) are used in a wide range of application fields such as catalysts, electronic devices, electrodes, electrical devices, fuel cells and high temperature materials due to their excellent electrical and thermal conductivity as well as chemical resistivity. Platinum group elements are generally associated with nickel-copper sulfides in magmatic rocks. Depending on the relative concentrations of the PGMs, they are produced either as the primary products or as by-products of the nickel and copper. However, PGMs natural resource deposits are strictly limited in countries such as South Africa and Russia. The annual supply of PGMs is only under 500 t. Considering the limited supply of PGMs, there will be a noticeable increase in the supply risk associated with PGMs in the near future. Therefore, it is extremely important to recover PGMs from secondary resources such as spent catalysts. This paper reviews on overview of PGMs extraction and recycling processes.

• Korean Chemical Engineering Research
• /
• v.61 no.4
• /
• pp.604-610
• /
• 2023

The nitrogen reduction reaction (NRR), which produces NH₃ by reducing N₂ under ambient conditions, is attracting attention as a promising technology that can reduce energy consumption in industrial processes. We investigated the adsorption behaviors at various active sites on the Ni (100) surface, which is widely used among catalytic metal surfaces capable of adsorbing and activating N₂, based on density-functional theory calculations. We also investigated two N₂ adsorption structures, so-called end-on and side-on structures. We find that for the end-on case, N₂ is adsorbed on a top site, and the reaction proceeded in a distal pathway, while for the side-on case, N₂ is adsorbed on a bridge site, and the reaction proceeded with enzymatic pathway. Finally, this study provides insight into the adsorption of metal catalyst surfaces for the NRR reactions based on the calculated Gibbs free energy profiles of the thermodynamically most favorable pathways.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.913-924
• /
• 1996

In this study HDS(hydrodesulfurization) of thiophene was researched over nickel catalysts added with small amounts of neodymium which were prepared by different methods such as unsupported coprepricipitated NdNi catalysts, unsupported intermetallic $NdNi_5$ catalysts, and carbon supported NdNi catalyst. The HDS activity was remarkably increased when a small amounts of neodymium was added to unsupported coprecipitated Ni catalysts. Thus it was known that the role of Nd is important in HDS of thiophene of Ni catalysts. For the case of unsupported intermetallic $NdNi_5$, the intermetallic crystallinity was destroyed to oxide and sulfide after calcination and presulfidation respectively. The HDS activity of thiophene can be explained by surface area of unsupported catalysts. And Nd acts like as structural promoter keeping the high surface area of unsupported catalysts. The HDS activity was increased by each ten times based on 1 gr. of nickel in the order of unsupported intermetallic $NdNi_5$, unsupported coprecipitated NdNi, and carbon supported NdNi catalysts according to different preparation method of catalysts.

• Journal of the Korean Chemical Society
• /
• v.51 no.6
• /
• pp.499-505
• /
• 2007

Monomeric complexes of nickel(II) having terdentate bis(imino)aryl ligands (N,C,N-pincer) are reported. New complexes (2,6-(ArN=CH)2C6H3)NiBr (Ar=2,6-dimethylphenyl (1), 2,6-diisopropylphenyl (2)) have been synthesized through oxidative addition of 1,3-(ArN=CH)2C6H3Br (bis(N-Ar)-2-bromoisophthalaldimine: Ar=Ph-2,6-Me2, Ph-2,6-iPr2) to Ni(COD)2 (COD=1,5-cyclooctadiene), in high yields. The development of a synthetic route to ligands and nickel complexes is outlined. The complexes were characterized by IR, 1H-NMR and elemental analysis. Full characterization of complexes 1 and 2 is discussed. An investigation into the catalytic activity of the complexes in ethylene polymerization was performed, resulting in no formation of polyethylenes but producing a small amount of oily oligomers. Preliminary results indicate that the pincer complexes were found to be inactive as catalysts in ethylene polymerization.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.309-313
• /
• 2011

The power capacitors used as vehicle inverters must have a small size, high capacitance, high voltage, fast response and wide operating temperature. Our thin film capacitor was fabricated by alumina layers as a dielectric material and a metal electrode instead of a liquid electrolyte in an aluminum electrolytic capacitor. We analyzed the micro structures and the electrical properties of the thin film capacitors fabricated by nano-channel alumina and metal electrodes. The metal electrode was filled into the alumina nano-channel by electroless nickel plating with polyethylene glycol and a palladium catalyst. The spherical metals were formed inside the alumina nano pores. The breakdown voltage and leakage current increased by the chemical reaction of the alumina layer and $PdCl_2$ solution. The thickness of the electroless plated nickel layer was 300 nm. We observed the nano pores in the interface between the alumina layer and the metal electrode. The alumina capacitors with nickel electrodes had a capacitance density of 100 $nF/cm^2$, dielectric loss of 0.01, breakdown voltage of 0.7MV/cm and leakage current of $10^4{\mu}A$.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.281-295
• /
• 2021

In this study, the direct amination of ethanol was performed over impregnated Ni on SiO2-Al2O3 mixed oxide catalysts prepared by varying Si/(Si + Al) molar ratio to 30 mol%. To characterize the physico-chemical properties of the catalysts used, X-ray diffraction (XRD), N2-physisorption, temperature-programmed desorption of iso-propyl alcohol (IPA-TPD), temperature-programmed desorption of ethanol (EtOH-TPD), temperature-programmed reduction with H2 (H2-TPR), H2-chemisorption and transmission electron microscopy (TEM) were used. The acidic property was continuously increased until Si/(Si + Al) = 30 mol% in SiO2-Al2O3 mixed oxides used. The dispersion of Ni metal and surface area, acid characteristics of the supported Ni catalyst have a complex effect on the catalytic reaction activity. The low reduction temperature of nickel oxide and acidic properties were beneficial to the formation of acetonitrile. In terms of conversion of ethanol, Ni/SiO2-Al2O3 catalyst with a molar ratio of 10 mol% Si/(Si+Al) showed the highest activity and a volcanic curve based on it. The tendency of results were consistent in the metal dispersion and catalytic activity.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4371-4376
• /
• 2011

In this work, we investigate the growth behavior of silicon oxide nanowires via a solid-liquid-solid process. Silicon oxide nanowires were synthesized at $1000^{\circ}C$ in an Ar and $H_2$ mixed gas. A pre-oxidized silicon wafer and a nickel film are used as the substrate and catalyst, respectively. We propose two distinctive growth modes for the silicon oxide nanowires that both act as a unique solid-liquid-solid growth process. We named the two growth mechanisms "grounded-growth" and "branched-growth" modes to characterize their unique solid-liquid-solid growth behavior. The two growth modes were classified by the generation site of the nanowires. The grounded-growth mode in which the grown nanowires are generated from the substrate and the branchedgrowth mode where the nanowires are grown from the side of the previously grown nanowires or at the metal catalyst drop attached at the tip of the nanowire stem.

• Resources Recycling
• /
• v.7 no.2
• /
• pp.9-15
• /
• 1998

Recovery af molybdenum in spent desulfuriring catalyst of petrochemical industries was studied from MfGnatc solulion which is a resultant of firstly remvercd vanadium by wet processes. In order to separate and recover molybdenum from upper mentioned rafinatz solution containing several mctal ions, such as molybdenum (1,100 ppm), vanadium (150 ppm), aluminium (19 ppm), and nickel (33 ppm), either adsorption technique by chelate resin or solvent extr~ction by tertiary amine as extractant was applied. In case of adsorption method, palyamine type chelate resin showed the highest selectivily far molybdenum ion up lo 60 ddm' of ancentration aftcr eluting with 3.0 rnolld~n' of NH,OH. On the othcr hand. molybdenum ion wa cffectlvely cxtractcd in Ule whole ranges of equilibrilrm pR by solvent extraction method with 10 ~01%-alamine 336 which was pretreated with 2N-HCI