• Journal of the Korean Applied Science and Technology
• /
• v.21 no.4
• /
• pp.289-299
• /
• 2004

Multi-walled carbon nanotubes (CNTs) were prepared by microwave plasma chemical vapor deposition (MPCVD) using various combination of binary catalysts and methane precursor. The maximum yield (10.3 %) of CNTs was obtained using a methane-hydrogen-nitrogen mixture with volume ratio of 1:1:2 at 1000 W of microwave power. As the microwave power increased up to 1000 W, the deposition yield of CNTs raised from 4.1 % to 10. 3 %. However, the prepared CNTs at 800 W showed the more crystalline structure than those prepared at 1000 W. The prepared CNTs over different binary catalysts had various structural conformations such as aligned cylinder, bamboo, and nanofibers. The Id/Ig value of CNTs over$Fe-Fe/Al_2O_3, $Co-Co/Al_2O_3, and $Co-Cu/Al_2O_3 were in the range of 0.89${\sim}$0.93. Among the various binary catalysts used, $Fe-Co./Al_2O_3 showed the highest yield.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.96-96
• /
• 2016

나노섬유(nanofiber), 나노선(nanowire), 그리고 나노튜브(nanotube)와 같은 1차원 구조의(one-dimensional structure) 나노재료는 벌크(bulk) 및 박막(film) 재료와는 다르게 물리적, 화학적으로 특이한 성질을 가지고 있으며, 이러한 성질은 나노재료의 구조, 형상, 크기 등에 큰 영향을 받는다. 첫 째, 전기방사(electrospinning) 공정을 이용한 나노섬유의 합성; 용액의 특성, 전기장 세기, 방사시간 등의 변수를 조절하게 되면 방출되는 재료의 형상을 입자 혹은 섬유상의 형태로 얻을 수 있으며, 전기방사를 통해 합성된 나노재료의 소결 온도 및 시간을 달리함으로써 나노입자의 크기를 조절할 수 있다. 또한, 템플레이트 합성법(template synthesis) 및 이중노즐(coaxial nozzle)을 이용해 속이 빈 형태인 중공(hollow) 구조의 나노섬유를 얻을 수 있으며, 전기방사에 사용되는 전구물질에 원하는 금속 및 산화물을 첨가함으로써 복합체(composite) 나노섬유를 얻을 수 있다. 둘 째, VLS(Vapor-Liquid-Solid) 공정을 이용한 나노선의 성장; 온도, 압력, 전구물질의 양, 그리고 시간 등의 변수를 조절하게 되면 원하는 직경 및 길이를 갖는 나노선을 성장시킬 수 있다. 그리고 ALD(Atomic Layer Deposition)를 이용해 나노선에 추가적인 층을 형성함으로써 코어-셀 구조를 형성할 수 있으며, 감마선, UV와 같은 공정을 이용해 귀금속 촉매를 나노선에 기능화 시킬 수도 있다. 코어-셀 구조를 갖는 나노선/나노섬유는 코어 혹은 셀 층의 전자나 홀의 이동을 유발하여 전자공핍층(electron depletion layer) 또는 정공축적층(hole accumulation layer)을 확대 및 축소시켜 센서의 초기저항을 증가시키거나 감소시키는 역할로써 이용되고 있으며, 특히, 셀 층의 두께가 셀 층 재료의 Debye length와 유사한 크기를 갖게 되면, 셀 층은 완전공핍층(fully depleted layer)을 형성해 최대의 감도를 나타낼 수 있다. 본 연구에서는 다양한 제조 공정을 통해 제작될 수 있는 1차원 나노-구조물을 가스센서에 적용하는 사례들을 소개하고, 이러한 가스센서의 감응성능을 향상시키기 위한 방법의 한 가지로 원자층증착법으로 나노선/나노섬유의 표면에 셀층을 형성하여 감응성 향상 메커니즘 및 관련 주요 변수들을 조사하고자 한다.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.539-548
• /
• 2016

The non-noble 1D nanofibers(NFs) prepared by electrospinning and calcination method were used as oxygen evolution reaction (OER) electrocatalyst for water electrolysis. The electrospinning process and rate of solution composition was optimized to prepare uniform and non-beaded PVP polymer electrospun NFs. The diameter and morphology of PVP NFs changed in accordance with the viscosity and ion conductivity. The clean metal precursor contained electrospun fibers were synthesized via the optimized electrospinning process and solution composition. The calcined $CuCo_2O_4$ NFs catalyst showed higher activity and long-term cycle stability for OER compared with other $Co_3O_4$, $NiCo_2O$ NF catalysts. Furthermore, the $CuCo_2O_4$ NFs maintained the OER activity during long-term cycle test compared with commercial $CuCo_2O_4$ nanoparticle catalyst due to unique physicochemical and electrochemical properties by1D nanostructure.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.555-559
• /
• 2016

A biodegradable nanofiber scaffolds using electrospining provide fibrous guidance cues for controlling cell fate that mimic the native extracellular matrix (ECM). It can create a pattern using conventional electrospining method, but has a difficulty to generate one or more pattern structures. Femtosecond(fs) laser ablation has much interested in patterning on biomaterials in order to distinguish the fundamental or systemic interaction between cell and material surface. The ablated materials with a short pulse duration using femtosecond laser that allows for precise removal of materials without transition of the inherent material properties. In this study, linear grooves and circular craters were fabricated on electrospun nanofiber scaffolds (poly-L-lactide(PLLA)) by femtosecond laser patterning processes. As parametric studies, pulse energy and beam spot size were varied to determine the effects of the laser pulse on groove size. We confirmed controlling pulse energy to $5{\mu}J-20{\mu}J$ and variation of lens maginfication of 2X, 5X, 10X, 20X created grooves of width to approximately $5{\mu}m-50{\mu}m$. Our results demonstrate that femtosecond laser processing is an effective means for flexibly structuring the surface of electrospun PLLA nanofibers.

• Smart Structures and Systems
• /
• v.25 no.1
• /
• pp.97-104
• /
• 2020

Due to the superior properties of nanoparticles, using them has been increased in concrete production technology. In this study, the effect of zinc oxide (ZnO) nanoparticles on the mechanical and smart properties of concrete was studied. At the first, the ZnO nanoparticles are dispersed in water using shaker, magnetic stirrer and ultrasonic devices. The nanoparticles with 3.5, 0.25, 0.75, and 1.0 volume percent are added to the concrete mixture and replaced by the appropriate amount of cement to compare with the control sample without any additives. In order to study the mechanical and smart properties of the concrete, the cubic samples for determining the compressive strength and cylindrical samples for determining tensile strength with different amounts of ZnO nanoparticles are produced and tested. The most important finding of this paper is about the smartness of the concrete due to the piezoelectric properties of the ZnO nanoparticles. In other words, the concrete in this study can produce the voltage when subjected to mechanical load and vice versa it can induce the mechanical displacement when subjected to external voltage. The experimental results show that the best volume percent for ZnO nanoparticles in 28-day samples is 0.5%. In other words, adding 0.5% ZnO nanoparticles to the concrete instead of cement leads to increases of 18.70% and 3.77% in the compressive and tensile strengths, respectively. In addition, it shows the best direct and reverse piezoelectric properties. It is also worth to mention that adding 3.5% zinc oxide nanoparticles, the setting of cement is stopped in the concrete mixture.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.274-281
• /
• 2009

Nylon 6 and nylon elastomer were prepared by anionic polymerization route. Nylon elastomers, composed of hard segment of polyamide(PA) and soft segment of polyether(PE), were synthesized by use of TDI terminated polyol with caprolactam. The morphology of the electrospun webs of nylon and nylon elastomers, observed by FE-SEM, showed that the porous electrospun web was composed of nanofibers, whose diameter were in the range of 100 to 180 nm. Their behavior of melting and crystallization and the chemical structure of nylon elastomers were investigated by DSC and ATR FT-IR. Result of tensile testing indicated that nylon has higher tensile strength and lower elongation than nylon elastomers. Atmospheric plasma(APP) with $O_2$ and $N_2$ as reactive gas modified the surface of electrospun nylon and electrospun nylon elastomers allowing them higher hydrophilicity, while APP with $CH_4$ as reactive gas modified the surface of polymers allowing higher hydrophobicity.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.5
• /
• pp.455-460
• /
• 2012

This work describes the hydriding chemical vapor synthesis (HCVS) of the $MgH_2$ in a hydrogen atmosphere and the product's hydriding-dehydridng properties. Mg powder was used as a starting material to synthesize $MgH_2$ and uniformly heated to a temperature of $600^{\circ}C$ for Mg vaporization. The effects of hydrogen pressure on the morphology and the composition of HCVS-$MgH_2$ were examined by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). It is clearly seen that after the HCVS process, the particle size of synthesized $MgH_2$ was drastically reduced to the submicron or micrometer-scale and these showed different shapes (needle-like nanofibers and angulated plate) depending on the hydrogen pressure. It was found that after the HCVS process, the $H_2$ desorption temperature of HCVS-$MgH_2$ decreased from 380 to $410^{\circ}C$, and the minimum hydrogen desorption tempreature of HCVS-$MgH_2$ powder with needle-like shape can be obtained. In addition, the enhanced hydrogen storage performance for needle-like $MgH_2$ was achieved during subsequent hydriding-dehydriding cycles.

• Textile Coloration and Finishing
• /
• v.32 no.3
• /
• pp.167-175
• /
• 2020

In this study, the optimum conditions for manufacturing PVDF nano web according to various electrospinning conditions such as solution concentration and applied voltage conditions were confirmed. The optimum spinning conditions were studied by analyzing the changes in the radioactivity of PVDF/TiO₂ nano web according to the TiO₂ content and the content of β-phase closely related to the piezoelectric properties under established conditions. As a result, it was confirmed that the concentration of the spinning solution was 20 wt%, the applied voltage was 25 kV, and the TiO₂ content was 5 phr. PVDF nano web and PVDF/TiO₂ nano web were observed morphologies through Scanning Electron Microscope(SEM) analysis. Formation of β-phase by electrospinning was confirmed by Fourier transform infrared spectroscopy(FT-IR) and X-ray Diffractometer(XRD), and the effect of the trapped nano web structure on the piezoelectric properties was investigated.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.322-331
• /
• 2017

Hydrogen evolution reaction(HER) was studied over $Ni_4Cr$ nanofibers(NFs) prepared by electrospinning method and oxidation/reduction heat treatment for alkaline water electrolysis. The physicochemical and electrochemical properties such as average diameter, lattice parameter, HER activity of synthesized $Ni_4Cr$ NFs could be modified by proper electrospinning process condition and reduction temperature. It was shown that $Ni_4Cr$ NFs had average diameter from 151 to 273 nm. Also, it exhibited the overpotential between 0.419 V and 0.526 V at $1mA/cm^2$ and Tafel slope of -334.75 mV to -444.55 mV per decade in 1 M KOH solution. These results indicate that $Ni_4Cr$ NFs with reduction heat treatment at $600^{\circ}C$ show thinnest diameter and highest HER activity among the other catalysts.

• Journal of Radiation Industry
• /
• v.5 no.4
• /
• pp.371-376
• /
• 2011

The surface property of the materials used in tissue engineering application has been essential to regulate cellular behaviors by directing their adhesion on the materials. To modulate surface property of the synthetic biodegradable materials, a variety of surface modification techniques have used to introduced surface functional groups or bioactive molecules, recently polydopamine coating method have been introduce as a facile modification method which can be coated on various materials such as polymers, metals, and ceramics regardless of their surface property. However, there are no reports about the degree of polydopamine coating on the materials with different hydrophilicity. In the present study, we prepared acrylic acid grafted nanofibrous meshes using electron-beam irradiation, and then coated meshes with polydopamine. Polydopamine successfully coated on the all meshes, both properties of acrylic acid and polydopamine were detected on the meshes. In addition, the degree of polydopamine deposition on the materials has been altered according to surface hydrophilicity, which was approximately 8-times greater than those on the non-modified materials. In conclusion, dual effect from the acrylic acid grafting and polydopamine may give a chance as a alternative tool in tissue engineering application.