• 제목/요약/키워드: nano-cellulose

검색결과 67건 처리시간 0.031초

나노셀룰로스를 활용한 쑥 추출물의 염색성 (The Dyeing Properties of Mugwort(Artemisia princeps) Extract using Nano-cellulose)

  • 박영미
    • 한국염색가공학회지
    • /
    • 제32권3호
    • /
    • pp.142-149
    • /
    • 2020
  • The purpose of this study was to investigate the dyeing properties of mugwort extract by nano-cellulose(n-cell). When dyeing cotton, rayon(artificial silk, called Ingyeon) and silk with mugwort extract, the difference with and without 2 wt% n-cell which it diluted to 0.6% treatment was compared. It was found that the addition of n-cell changed the values of L, -a(+red ~ -green), and b(+yellow ~ -blue) of all scoured cotton, rayon and silk fabrics, compared to dyeing only mugwort extract. Furthermore, it was confirmed that the ΔE and the K/S value slightly increased in all of the dyed cotton, rayon, and silk fabrics treated with n-cell at the same time as dyeing compared to the untreated ones. Therefore, by treating the fabric with n-cell, a natural cellulose component, at the same time as dyeing, it is expected to maintain stable fastness, which is a disadvantage of dyeing using natural dyes, and contribute to the utilization and commercialization of other natural dyes.

분무방식에 의한 NFC(Nano-Fibrillated Cellulose)의 제지공정 적용 방안 탐색 연구 (Studies on Application of Spray of Nano-fibrillated Cellulose to Papermaking Process)

  • 이광섭;김창근;이재훈;이태주;류정용
    • 펄프종이기술
    • /
    • 제47권4호
    • /
    • pp.5-12
    • /
    • 2015
  • In recent years, it had focused on the improvement of paper properties by addition of NFC (Nano-fibrillated Cellulose). Although the addition of NFC to wet-end of papermaking process could be suggested as a new solution to improve the strength properties of paper, it was not possible to avoid the bad drainage caused by the added NFC's chocking pores of wet web. Instead of the direct addition to wet-end, spraying of NFC to web in wire-section was tried in this study and evaluated by checking various paper properties including surface smoothness, tensile strength, folding endurance and stiffness. According to the increase of spraying amount of NFC, above mentioned paper properties were enhanced without excessive deterioration of drainage. Compared with direct introduction to wet-end, spraying could be regarded as a more proper method to enhance the surface smoothness and strength properties of paper.

Cellulose Nanocrystals as Advanced "Green" Materials for Biological and Biomedical Engineering

  • Sinha, Arvind;Martin, Elizabeth M.;Lim, Ki-Taek;Carrier, Danielle Julie;Han, Haewook;Zharov, Vladimir P.;Kim, Jin-Woo
    • Journal of Biosystems Engineering
    • /
    • 제40권4호
    • /
    • pp.373-393
    • /
    • 2015
  • Background: Cellulose is a ubiquitous, renewable and environmentally friendly biopolymer, which has high promise to fulfil the rising demand for sustainable and biocompatible materials. Particularly, the recent progress in the synthesis of highly crystalline cellulose-based nanoscale biomaterials, namely cellulose nanocrystals (CNCs), draws significant attention from many research communities, ranging from bioresource engineering, to materials science and engineering, to biological and biomedical engineering to bionanotechnology. The feasibility of harnessing CNCs' unique biophysicochemical properties has inspired their basic and applied research, offering much promise for new biomaterials with diverse advanced functionalities. Purpose: This review focuses on vital issues and topics on the recent advances in CNC-based biomaterials with potential, in particular, for bionanotechnology and biological and biomedical engineering. The challenges and limitations of CNC technology are discussed as well as potential strategies to overcome them, providing an essential source of information in the exploration of possible and futuristic applications of the CNC-based functional "green" nanomaterials. Conclusion: CNCs offer exciting possibilities for advanced "green" nanomaterials, driving innovative research and development in a wide range of fields, including biological and biomedical engineering.

Effects of constituents in CNT pastes on the field emission characteristics of carbon nanotubes

  • Yoon, Seung-Il;Kim, Sam-Soo;Lee, Yang-Kyu;Kim, Tae-Kwon;Lee, Dong-Gu
    • 한국정보디스플레이학회:학술대회논문집
    • /
    • 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
    • /
    • pp.1206-1209
    • /
    • 2006
  • Carbon nanotubes (CNTs) have been significantly used for the field emitters for display applications. However, the lifetime of CNT emitters which are formed by screen printing technique is not guaranteed yet, because the constituents in CNT paste affect the lifetime of CNTs. The CNT pastes for screen printing are normally composed of organic vehicles (nitro cellulose, ethyl cellulose, etc) and additives (glass frits, ITO, etc) with CNTs. In this study, the effects of constituents in CNT pastes on the lifetime and emission characteristics of CNTs were investigated by thermal and electrical analysis. Use of glass frits worsened the lifetime and electron emission of CNTs. However, an addition of ITO to CNT paste rather improved the lifetime of CNTs. Degradation of CNTs was small when nitro cellulose was used in CNT paste as an organic vehicle.

  • PDF

Removal of BP-3 Endocrine Disrupting Chemical (EDC) using cellulose acetate and ZnOnano particles mixed matrix membranes

  • Rajesha, B.J.;Chandan, H.R.;Sunil, K.;Padaki, Mahesh;Balakrishna, Geetha R.
    • Membrane and Water Treatment
    • /
    • 제7권6호
    • /
    • pp.507-520
    • /
    • 2016
  • The effect of ZnO on cellulose acetate in the removal of benzophenone-3 (BP-3) was investigated. The benzophenone-3 (BP-3) which is an endocrine disrupting chemical (EDC) was completely removed (100%) from the drinking water using Cellulose Acetate (CA) and zinc oxide (ZnO) composite membranes. The membranes were prepared by DIPS method and the filtration experiments were conducted by dead end filtration unit. The macrostructure of the membrane were studied by ATR-IR and XRD Spectra's. Atomic force microscopy (AFM) and Scanning electron microscopy (SEM) were used to study the micro properties of the membranes. The laboratory experiments such as water uptake study and pure water flux performed to confirm the increasing hydrophilicity. The enhancing hydrophilicity was confirmed with respect to higher the concentration of nanoparticles. Evaluation of BP-3 removal was carried in different experimental conditions, such as, different Trans membrane pressure and different concentration of feed. The membrane with low pressure showed better performance by rejecting 100% of BP-3. However, 1 ppm, 3 ppm and 6 ppm of feed solution was used and among them 3 ppm of feed solution gives 100% rejection. The ZnO nanoparticales enhances the performance of CA membrane by showing maximum rejection.

Effects of Constituents in CNT Pastes on the Field Emission Characteristics of Carbon Nanotubes

  • 김석환;이동구
    • 한국전기전자재료학회논문지
    • /
    • 제24권3호
    • /
    • pp.245-249
    • /
    • 2011
  • Carbon nanotubes (CNTs) have been significantly used for the field emitters for display applications. However, the lifetime of CNT emitters which are formed by screen printing technique is not guaranteed yet, because the constituents in CNT paste affect the lifetime of CNTs. The CNT pastes for screen printing are normally composed of organic vehicles (nitro cellulose, ethyl cellulose, etc) and additives (glass frits, indium tin oxide (ITO), etc) with CNTs. In this study, the effects of constituents in CNT pastes on the lifetime and emission characteristics of CNTs were investigated by thermal and electrical analysis. Use of glass frits worsened the lifetime and electron emission of CNTs. However, an addition of ITO to CNT paste rather improved the lifetime of CNTs. Degradation of CNTs was small when nitro cellulose was used in CNT paste as an organic vehicle.

Influence of Nano-Cellulose Dispersant on the Vulcanization Characteristics, Viscoelastic Properties, and Mechanical Properties of Silica-SBR Compounds

  • Kim, Jung Soo;Kim, Dong Hyun
    • Elastomers and Composites
    • /
    • 제55권3호
    • /
    • pp.215-221
    • /
    • 2020
  • Silica/SBR (styrene-butadiene rubber) compounds are the primary constituents of tire treads. Furthermore, the excellent dynamic viscoelastic properties of silica lead to good fuel efficiencies. However, the silanol group on the surface of silica does not mix well with non-polar rubber because of its polarity. This incompatibility causes aggregation due to the occurrence of hydrogen bonding between the hydroxyl groups, thereby reducing the dispersibility of silica. Recently, the wet master batch (WMB) process has been applied to overcome these disadvantages, and research on silica dispersants that can be used in the WMB process has been increasing. In this study, we prepared silica/SBR compounds by using three types of eco-friendly cellulose-based dispersants in the WMB process, namely: cellulose-, sodium carboxymethyl cellulose, and nanocellulose-based dispersants. Subsequently, we compared the vulcanization characteristics, viscoelastic properties, and mechanical properties of the compounds. The silica dispersibility in the rubber compounds was improved with the addition of the nano-cellulose dispersant, resulting in the enhancement of the workability, hardness, tensile strength, and wear resistance of the SBR compound.

셀룰로오스 아세테이트 안경테 판재에 관한 연구 (Studies on the Cellulose Acetate Glasses Frame Sheet)

  • 이해성;이성준;정상원;김현철;김은주;고영준;이세근
    • 한국안광학회지
    • /
    • 제16권1호
    • /
    • pp.13-19
    • /
    • 2011
  • 목적: 본 연구는 국외에서 판매중인 셀룰로오스 아세테이트 안경테용 판재(수입 CA판재, overseas company's cellulose acetate glasses frame sheet)의 특성을 평가하고 안경테용 CA 판재로서 적합한 공업용 셀룰로오스 아세테이트 레진(공업용 CA레진, industrial cellulose acetate resin)을 선정하여 그 소재의 최적 용융 압출 조건을 도출하는 데 목적이 있다. 방법: 수입 CA판재의 특성을 고찰하기 위해 $^1H$-NMR, GPC, TGA 분석을 실시하고, 공업용 CA레진의 최적 배합 조건 및 용융 압출 조건을 도출한다. 또한 hot press에 의해 제조 된 3개국의 수입 CA판재와 공업용 CA레진 성형체의 물성을 비교 평가를 실시하였다. 결과: 수입 CA판재의 특성 분석 결과, virgin CA를 가소화시키기 위해 사용된 가소제는 diethyl phthalate이며 가소제의 함량은 30 wt% 내외임을 확인하였다. 용융 압출 시험 결과, 압출온도는 190~200${^{\circ}C}$에서 공업용 CA레진의 충분한 용융거동 및 압출성을 보였으며 성형체 또한 안경테용 물성을 만족하는 수준인 2.3 kgf/$mm^2$임을 확인하였다. 결론: 30 wt%의 가소제 함량을 가진 공업용 CA레진의 경우, 중국의 CA판재를 대체하여 안경테용 셀룰로오스 아세테이트 판재 제조에 적합한 소재로 판단된다.

High Luminescence Properties of YPV nano size phosphors by a Liquid Phase Precursor Method

  • Jo, D.S.;Dulda, A.;Masaki, T.;Yoon, D.H.
    • 한국정보디스플레이학회:학술대회논문집
    • /
    • 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
    • /
    • pp.1293-1296
    • /
    • 2009
  • The synthesis of nano-size ($Y_{0.955}Eu_{0.1}$)($P_{0.7}V_{0.45}$)$O_4$ red phosphors were conducted by using a Liquid Phase Precursor (LPP) method. In this method, cellulose pulp was used as a template showing the micro fibre structures to obtain the nano size YPV red phosphor. Aqueous solutions of raw materials were impregnated into cellulose pulp and subsequently impregnated pulp was dried and fired at $800-1200^{\circ}C$ for 1h. The effect of luminescence properties on compositions and temperatures was evaluated with photoluminescence spectrum, X-ray diffraction and FE-SEM, and TEM. High efficiency (~110%) of phosphor of size of ~500nm fired at $1150^{\circ}C$ was obtained compared with the micro size of commercial product. High efficiency behaviors of nano size phosphors were discussed in this paper.

  • PDF

Titanized or Zirconized Porous Silica Modified with a Cellulose Derivative as New Chiral Stationary Phases

  • Seo, You-Jin;Kang, Gyoung-Won;Park, Seong-Tae;Moon, Myeong-Hee;Park, Jung-Hag;Cheong, Won-Jo
    • Bulletin of the Korean Chemical Society
    • /
    • 제28권6호
    • /
    • pp.999-1004
    • /
    • 2007
  • Spherical porous silica supports modified with titanium or zirconium alkoxides were prepared, and allyl groups were chemically attached to the titanized or zirconized silica supports, and the product was cross-polymerized with a double bond containing cellulose derivative to yield new CSPs (chiral stationary phases). Magic angle spinning 13C solid state NMR and elemental analysis were used to characterize the CSPs. The performances of the chiral stationary phases were examined in comparison with a conventional chiral stationary phase. Spherical porous silica particles modified with 3,5-dimethylphenylcarbamate of cellulose were prepared and used as the conventional chiral stationary phase. Chromatographic data were collected for a few pairs of enantionmers in heptane/2-propanol mixed solvents of various compositions with the three chiral columns and the results were comparatively studied. The separation performance of the chrial phase made of the titanized silica was better than the others, and the separation performance of the chiral phase of the zirconized silica was comparable to that of the conventional chiral phase. The superiority of titanized silica over bare or zirconized silica in chiral separation seemed to be owing to the better yield of crosslinking (monitored by increase of carbon load) for titanized silica than for the others.