• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.3
• /
• pp.120-125
• /
• 2002

The aim of the present work is to optimized the annealing parameter in both front and back screen printed contacts realization on p-type multicrystalline silicon and with phosphorus diffused. The RTA treatments were carried out at various temperatures from 600 to 850$\^{C}$ and annealing time ranging from 3 min to 5 min in air, O$_2$and N$_2$ ambiance. The contacts parameters are obtained according to Transmission Line Model measurements. A good RTA cycle is obtained with a temperature plateau of 700$\^{C}$-750$\^{C}$ and annealing ambiance of air. Several processing parameters required for good cell efficiency are discussed with an emphasis placed on the critical role of the glass frit in the aluminum paste. A anamolus behaviour of Aluminum n-doping on p-type Si wafer, contact at high temperature have also been studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.456-456
• /
• 2009

Boron doping on an n-type Si wafer is requisite process for IBC (Interdigitated Back Contact) solar cells. Fiber laser annealing is one of boron doping methods. For the boron doping, uniformly coated or deposited film is highly required. Plasma enhanced chemical vapor deposition (PECVD) method provides a uniform dopant film or layer which can facilitate doping. Because amorphous silicon layer absorption range for the wavelength of fiber laser does not match well for the direct annealing. In this study, to enhance thermal affection on the existing p-a-Si:H layer, a ${\mu}c$-Si:H intrinsic layer was deposited on the p-a-Si:H layer additionally by PECVD. To improve heat transfer rate to the amorphous silicon layer, and as heating both sides and protecting boron eliminating from the amorphous silicon layer. For p-a-Si:H layer with the ratio of $SiH_4$ : $B_2H_6$ : $H_2$ = 30 : 30 : 120, at $200^{\circ}C$, 50 W, 0.2 Torr for 30 minutes, and for ${\mu}c$-Si:H intrinsic layer, $SiH_4$ : $H_2$ = 10 : 300, at $200^{\circ}C$, 30 W, 0.5 Torr for 60 minutes, 2 cm $\times$ 2 cm size wafers were used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 20 ~ 27 % of power, 150 ~ 160 kHz, 20 ~ 50 mm/s of marking speed, and $10\;{\sim}\;50 {\mu}m$ spacing with continuous wave mode of scanner lens showed the correlation between lifetime and sheet resistance as $100\;{\Omega}/sq$ and $11.8\;{\mu}s$ vs. $17\;{\Omega}/sq$ and $8.2\;{\mu}s$. Comparing to the singly deposited p-a-Si:H layer case, the additional ${\mu}c$-Si:H layer for doping resulted in no trade-offs, but showed slight improvement of both lifetime and sheet resistance, however sheet resistance might be confined by the additional intrinsic layer. This might come from the ineffective crystallization of amorphous silicon layer. For the additional layer case, lifetime and sheet resistance were measured as $84.8\;{\Omega}/sq$ and $11.09\;{\mu}s$ vs. $79.8\;{\Omega}/sq$ and $11.93\;{\mu}s$. The co-existence of $n^+$layeronthesamesurfaceandeliminating the laser damage should be taken into account for an IBC solar cell structure. Heavily doped uniform boron layer by fiber laser brings not only basic and essential conditions for the beginning step of IBC solar cell fabrication processes, but also the controllable doping concentration and depth that can be established according to the deposition conditions of layers.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.75-80
• /
• 2019

Silicon solar cells have been widely used as a most promising renewable energy source due to eco-friendliness and high efficiency. As modules of silicon solar cells are connected in series for a practical electricity generation, a large voltage of 500-1,500 V is applied to the modules inevitably. Potential-induced degradation (PID), a deterioration of the efficiency and maximum power output by the continuously applied high voltage between the module frames and solar cells, has been regarded as the major cause that reduces the lifetime of silicon solar cells. In particular, the migration of the $Na^+$ ions from the front glass into Si through the anti-reflection coating and the accumulation of $Na^+$ ions at stacking faults inside Si have been reported as the reason of PID. In this research, the thickness effect of $SiO_x$ layer that can block the migration of $Na^+$ ions on the reduction of PID is investigated as it is incorporated between anti-reflection coating and p-n junction in p-type PERC solar cells. From the measurement of shunt resistance, efficiency, and maximum power output after the continuous application of 1,000 V for 96 hours, it is revealed that the thickness of $SiO_x$ layer should be larger than 7-8 nm to reduce PID effectively.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1738-1740
• /
• 1999

This paper deals with a novel structure of poly-Si solar cell. A solar cell conversion efficiency was degraded by grain boundary effect in Polycrystalline silicon. To reduce grain boundary effect, we performed a preferential grain boundary etching, $POCl_3$ n-type emitter doping, and then ITO film growth on poly-Si. Among the various preferential etchants, Schimmel etch solution exhibited the best result having grain boundary etch depth about $10{\mu}m$. RF magnetron sputter grown ITO films showed a low resistivity of $10^{-4}\Omega-cm$ and high transmittance of 85%. With well fabricated poly-Si solar cells. we were able to achieve as high as 15% conversion efficiency at the input power of 20mW/$cm^2$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.30.1-30.1
• /
• 2011

Silicon is one of useful materials in various industry such as semiconductor, solar cell, and secondary battery. The metallic silicon produces generally melting process for ingot type or chemical vapor deposition (CVD) for thin film type. However, these methods have disadvantages of high cost, complicated process, and consumption of much energy. Electrodeposition has been known as a powerful synthesis method for obtaining metallic species by relatively simple operation with current and voltage control. Unfortunately, the electrodeposition of the silicon is impossible in aqueous electrolyte solution due to its low oxidation-reduction equilibrium potential. Ionic liquids are simply defined as ionic melts with a melting point below $100^{\circ}C$. Characteristics of the ionic liquids are high ionic conductivities, low vapour pressures, chemical stability, and wide electrochemical windows. The ionic liquids enable the electrochemically active elements, such as silicon, titanium, and aluminum, to be reduced to their metallic states without vigorous hydrogen gas evolution. In this study, the electrodeposion of silicon has been investigated in ionic liquid of 1-butyl-3-methylpyrolidinium bis (trifluoromethylsulfonyl) imide ([bmpy]$Tf_2N$) saturated with $SiCl_4$ at room temperature. Also, the effect of electrode materials on the electrodeposition and morphological characteristics of the silicon electrodeposited were analyzed The silicon electrodeposited on gold substrate was composed of the metallic Si with single crystalline size between 100~200nm. The silicon content by XPS analysis was detected in 31.3 wt% and the others were oxygen, gold, and carbon. The oxygen was detected much in edge area of th electrode due to $SiO_2$ from a partial oxidation of the metallic Si.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.335-336
• /
• 2009

저가격 고효율 실리콘 태양전지를 구현하기 위하여 핵심적으로 적용되는 공정인 SOD(Spin on Doping) 확산공정 최적화에 관하여 연구하였다. n-type 도핑 물질로는 인(P509)을 사용하였으며, Spinning 속도와 Spinning 시간을 각 3000 rpm, 30 초로 고정하고 급속 열처리로에서 확산 온도와 확산 시간을 $800\;^{\circ}C\;{\sim}\;950\;^{\circ}C$, 2 분에서 20 분까지 가변하며 확산공정을 실시하였다. 4-Point Probe 장비로 에미터 표면 저항을 측정한 결과 확산 온도 $850\;^{\circ}C$에서 5분간 열처리 하여 확산 공정을 하였을 때 저가의 고효율 실리콘 태양전지를 구현하는데 적용 하기위한 $30\;{\sim}\;50\;{\Omega}$-sq의 에미터 표면 저항을 만족 시키는 $36\;{\Omega}$-sq의 값을 얻을 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.313.1-313.1
• /
• 2013

현재 결정질 실리콘 태양전지의 전 후면 전극의 형성은 스크린 프린팅 방법이 주를 이루고 있다. 스크린 프린팅 방법은 쉽고 빠르게 인쇄가 가능한 반면 단가가 높고 금속 페이스트에 첨가된 여러 혼합물에 의해서 전극과 기판 사이의 저항이 크다는 단점이 있다. 본 논문에서는 스크린 프린팅 방법으로 태양전지의 seed layer를 인쇄하고, Cu도금을 진행함으로써 태양전지의 전기적 특성을 비교하였다. 주요 전극 형성을 Cu 도금을 사용함으로써 전극과 기판사이의 저항을 감소시키고 값비싼 Ag페이스트를 값싼 Cu로 대체함으로써 가격을 낮출 수 있는 장점이 있다. 실험에 사용된 Si 웨이퍼 특성은 $156{\times}156$ mm2, 200 ${\mu}m$, 0.5-3.0 ${\Omega}{\cdot}cm$ and p-type 웨이퍼를 사용하였다. 웨이퍼는 표면조직화, p-n접합 형성, 반사방지막 코팅을 하였으며 스크린 프린팅 방법을 이용해 전 후면 전극을 인쇄하고 열처리 과정을 통해 전극을 형성하였다. 이 후 전면에 Cu도금을 실행하여 태양전지를 완성하였다. 완성된 태양전지는 솔라 시뮬레이터 및 TLM패턴을 이용하여 전기적 특성을 분석하였으며, SEM과 linescan, 광학현미경 등을 이용하여 전극을 분석하였다.

• Current Photovoltaic Research
• /
• v.7 no.1
• /
• pp.9-14
• /
• 2019

Carrier selective solar cell structure has allured curiosity of photovoltaic researchers due to the use of wide band gap transition metal oxide (TMO). Distinctive p/n-type character, broad range of work functions (2 to 7 eV) and risk free fabrication of TMO has evolved new concept of heterojunction intrinsic thin layer (HIT) solar cell employing carrier selective layers such as $MoO_x$, $WO_x$, $V_2O_5$ and $TiO_2$ replacing the doped a-Si layers on either front side or back side. The p/n-doped hydrogenated amorphous silicon (a-Si:H) layers are deposited by Plasma-Enhanced Chemical Vapor Deposition (PECVD), which includes the flammable and toxic boron/phosphorous gas precursors. Due to this, carrier selective TMO is gaining popularity as analternative risk-free material in place of conventional a-Si:H. In this work hole selective materials such as $MoO_x$, $WO_x$ and $V_2O_5$has been investigated. Recently $MoO_x$, $WO_x$ & $V_2O_5$ hetero-structures showed conversion efficiency of 22.5%, 12.6% & 15.7% respectively at temperature below $200^{\circ}C$. In this work a concise review on few important aspects of the hole selective material solar cell such as historical developments, device structure, fabrication, factors effecting cell performance and dependency on temperature has been reported.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.30-37
• /
• 1989

The PIN type a-SiC:H/a-Si:H heterojunction solar cells were fabricated by using the rf glow discharge decomposition of $SiH_4$ mixed with $CH_4,B_2,H_6\;and\;PH_3.$ The efficiency of the solar cell of the $SnO_2/ITO$ was higher than that of ITO transparent oxide layer by 1.5%. The P layer was prepared with the thickness of $100{\AA}$ and $CH_4/SiH_4$ ration of 5. The I layer has been deposited on the P layer and it is not pure intrinsic but near N type. So $SiH_4$ mixed with $B_2H_6$ of 0.3ppm was used to change this N type nature to intrinsic having the thickness of 5000${\AA}$. And consecutively, the N layer was deposited with t ethickness of $400{\AA}$ using $SiH_4/PH_3$ mixtures. The solar cell demonstrated 0.94V of $V_{oc'}$ 14.6mA/cm of $J_{sc}$ and 58.2% of FF, resulting the efficiency of 8.0%. To minimize loss by the reflection of light, $MgF_2$ layer was coated on the lgass and the efficiency was improved by 0.5%. Therefore, the solar cell indicated overall efficiency of 8.5%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.366-366
• /
• 2010

Simulation Program (AFORS-HET 2.4.1) was used, include the basic structure of crystalline silicon thin film as above, below Intrinsic a-Si:H films bonded symmetrical structure (Symmetrical structure) were used. Efficiency with variation of the concentration was grown by the a-Si p-type with increasing concentrations of Na, efficiency with increasing a-Si n-type of Nd Concentrations was not changed, was decreased rapidly when concentrations were decreased. Efficiency was increased when c-Si n-type of Nd concentration was increased, otherwise efficiency was decreased when concentration was decreased.