• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.6
• /
• pp.37-43
• /
• 1999

Two-way addressing method has been proposed for efficient VLSI implementation of Euclidean calculation circuit for pipelined Reed-Solomon decoder. This new circuit is operating with single clock while exploiting maximum parallelism, and uses register addressing instead of register shifting to minimize the switching power. Logic synthesis shows the circuit with the new scheme takes 3,000 logic gates, which is about 40% reduction from the previous 5,000 gate implementation. Computer simulation also shows the power consumption is about 3mW. The previous implementation with multiple clock consumed about 5mW.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.531-540
• /
• 2019

Spectral Amplitude Coding Optical Code Division Multiple Access (SAC OCDMA) is an advanced technique in asynchronous environments. This paper proposes design and implementation of a novel quantum logic gate (QLG) code, with code construction algorithm generated without following any code mapping procedures for SAC system. The proposed code has a unitary matrices property with maximum overlap of one chip for various clients and no overlaps in spectra for the rest of the subscribers. Results indicate that a single algorithm produces the same length increment for codes with weight greater than two and follows the same signal to noise ratio (SNR) and bit error rate (BER) calculations for a higher number of users. This paper further examines the performance of a QLG code based SAC-OCDMA system with NAND and direct detection techniques. BER analysis was carried out for the proposed code and results were compared with existing MDW, RD and GMP codes. We demonstrate that the QLG code based system performs better in terms of cardinality, which is followed by improved BER. Numerical analysis reveals that for error free transmission (10^-9), the suggested code supports approximately 170 users with code weight 4. Our results also conclude that the proposed code provides improvement in the code construction, cross-correlation and minimization of noises.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.6
• /
• pp.389-397
• /
• 2015

Recently, wave propagation imaging based on laser scanning-generated elastic waves has been intensively used for nondestructive inspection. However, the proficiency of the conventional software based system reduces when the scan area is large since the processing time increases significantly due to unavoidable processor multitasking, where computing resources are shared with multiple processes. Hence, the field programmable gate array (FPGA) was introduced for a wave propagation imaging method in order to obtain extreme processing time reduction. An FPGA board was used for the design, implementing post-processing ultrasonic wave propagation imaging (UWPI). The results were compared with the conventional system and considerable improvement was observed, with at least 78% (scanning of $100{\times}100mm^2$ with 0.5 mm interval) to 87.5% (scanning of $200{\times}200mm^2$ with 0.5 mm interval) less processing time, strengthening the claim for the research. This new concept to implement FPGA technology into the UPI system will act as a break-through technology for full-scale automatic inspection.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.234-238
• /
• 2003

In this work, we have designed a fully integrated 2.4GHz LC-tuned voltage-controlled oscillator (VCO) with multiple tuning inputs for a $0.25-{\mu}m$ standard CMOS Process. The design of voltage-controlled oscillator is based on an LC-resonator with a spiral inductor of octagonal type and pMOS-varactors. Only two metal layer have been used in the designed inductor. The frequency tuning is achieved by using parallel pMOS transistors as varactors and back-gate tuned pMOS transistors in an active region. Coarse tuning is achieved by using 3-bit pMOS-varactors and fine tuning is performed by using back-gate tuned pMOS transistors in the active region. When 3-bit digital and analog inputs are applied to the designed circuits, voltage-controlled oscillator shows the tuning feature of frequency range between 2.3 GHz and 2.64 GHz. At the power supply voltage of 2.5 V, phase noise is -128dBc/Hz at 3MHz offset from the carrier, Total power dissipation is 7.5 mW.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.32-36
• /
• 2003

In this work, we have designed a fully integrated 2.4GHz LC-tuned voltage-controlled oscillator (VCO) with multiple tuning inputs for a 0.25-$\mu\textrm{m}$ standard CMOS process. The design of voltage-controlled oscillator is based on an LC-resonator with a spiral inductor of octagonal type and pMOS-varactors. Only two metal layer have been used in the designed inductor. The frequency tuning is achieved by using parallel pMOS transistors as varactors and back-gate tuned pMOS transistors in an active region. Coarse tuning is achieved by using 3-bit pMOS-varactors and fine tuning is performed by using back-gate tuned pMOS transistors in the active region. When 3-bit digital and analog inputs are applied to the designed circuits, voltage-controlled oscillator shows the tuning feature of frequency range between 2.3 GHz and 2.64 GHz. At the power supply voltage of 2.5 V, phase noise is -128dBc/Hz at 3MHz offset from the carrier. Total power dissipation is 7.5 mW.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.73-81
• /
• 2014

In this paper, multiple gate locations and process conditions under concern are automatically optimized by considering robustness to minimize the injection pressure required to mold an automotive dashboard. Computer simulation-based experiments using orthogonal arrays(OA) and a design-range reduction algorithm are consolidated into an iterative search scheme, which is then used as a tool for the optimization process. The robustness of a design is evaluated using an OA-based simulation of process fluctuations due to noise as well as the signal-to-noise ratio. The optimal design solution for the automotive dashboard shows that the robustness of the injection pressure is significantly improved when compared to the initial design. As a result, both the die clamping force and the pressure distribution in the part cavity are also much improved in terms of their robustness.

• ETRI Journal
• /
• v.38 no.4
• /
• pp.645-653
• /
• 2016

This paper demonstrates the performance of a metal-substrate power module with multiple fabricated chips for a high current electrical application, and evaluates the proposed module using a 1.5-kW sinusoidal brushless direct current (BLDC) motor. Specifically, the power module has a hybrid structure employing a single-layer heat-sink extensible metal board (Al board). A fabricated motor driver IC and trench gate DMOSFET (TDMOSFET) are implemented on the Al board, and the proper heat-sink size was designed under the operating conditions. The fabricated motor driver IC mainly operates as a speed controller under various load conditions, and as a multi-phase gate driver using an N-ch silicon MOSFET high-side drive scheme. A fabricated power TDMOSFET is also included in the fabricated power module for three-phase inverter operation. Using this proposed module, a BLDC motor is operated and evaluated under various pulse load tests, and our module is compared with a commercial MOSFET module in terms of the system efficiency and input current.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.30-33
• /
• 2008

Injection Molding is the most effective process for mass production of plastic parts. The injection molding process is composed with several steps such as Filling, Packing, Holding, Cooling, Ejecting. Among them, filling and packing process should be considered carefully to improve accuracy of dimension, surface quality of plastic parts. Usually the quality above-mentioned is managed with weight of part after molding on the field. In this paper, a series of experiment for molding automotive front bumper was conducted with cavitity temperature sensor to optimize switch-over time(V-P switching), hot runner vale gate sequence time during filling and packing step for the purpose of uniform quality, weight at every molding. As a result, it was found that it is effective method to use temperature sensor in injection molding for quality control of plastic molding.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1301-1304
• /
• 2008

In this study, we used a multiple phase scheme for the clock in the dual-pull-down driver for TFT display panels. In this scheme, the turn-on time for the transistors in the dual-pull-down structure was reduced from 1/2 to 1/4 or 1/8 of the period cycle time. While keeping proper operation of the transistor size of circuit was fine tuned to achieve an optimal performance. The relation between the active time and the transistor dimensions was obtained for the optimal design.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.823-826
• /
• 2003

FPGA-based logic emulator with lane gate capacity generally comprises a large number of FPGAs connected in mesh or crossbar topology. However, gate utilization of FPGAs and speed of emulation are limited by the number of signal pins among FPGAs and the interconnection architecture of the logic emulator. The time-multiplexing of interconnection wires is required for multi-FPGA system incorporating several state-of-the-art FPGAs. This paper proposes a circuit partitioning algorithm called SCATOMi(SCheduling driven Algorithm for TOMi)for multi-FPGA system incorporating four to eight FPGAs where FPGAs are interconnected through TOMi(Time-multiplexed, Off-chip, Multicasting interconnection). SCATOMi improves the performance of TOMi architecture by limiting the number of inter-FPGA signal transfers on the critical path and considering the scheduling of inter-FPGA signal transfers. The performance of the partitioning result of SCATOMi is 5.5 times faster than traditional partitioning algorithms. Architecture comparison show that the pin count is reduced to 15.2%-81.3% while the critical path delay is reduced to 46.1%-67.6% compared to traditional architectures.