• 한국분말재료학회지
• /
• 제26권1호
• /
• pp.11-15
• /
• 2019

In this study, a method to remove residual powder on a multi-layered graphene and a new approach to transfer multi-layered graphene at once are studied. A graphene one-step transfer (GOST) method is conducted to minimize the residual powder comparison with a layer-by-layer transfer. Furthermore, a residual powder removing process is investigated to remove residual powder at the top of a multi-layered graphene. After residual powder is removed, the sheet resistance of graphene is decreased from 393 to 340 Ohm/sq in a four-layered graphene. In addition, transmittance slightly increases after residual powder is removed from the top of the multi-layered graphene. Optical and atomic-force microscopy images are used to analyze the graphene surface, and the Ra value is reduced from 5.2 to 3.7 nm following residual powder removal. Therefore, GOST and residual powder removal resolve the limited application of graphene electrodes due to residual powder.

• Journal of Mechanical Science and Technology
• /
• 제19권5호
• /
• pp.1065-1071
• /
• 2005

In this study, residual stress distribution in multi-stacked film by MEMS (Micro-Electro Mechanical System) process is predicted using Finite Element method (FEM). We evelop a finite element program for residual stress analysis (RESA) in multi-stacked film. The RESA predicts the distribution of residual stress field in multi-stacked film. Curvatures of multi­stacked film and single layers which consist of the multi-stacked film are used as the input to the RESA. To measure those curvatures is easier than to measure a distribution of residual stress. To verify the RESA, mean stresses and stress gradients of single and multi layers are measured. The mean stresses are calculated from curvatures of deposited wafer by using Stoney's equation. The stress gradients are calculated from the vertical deflection at the end of cantilever beam. To measure the mean stress of each layer in multi-stacked film, we measure the curvature of wafer with the left film after etching layer by layer in multi-stacked film.

• 한국정밀공학회지
• /
• 제26권4호
• /
• pp.100-106
• /
• 2009

The current tendency toward light weight and fast machines has lead to a need to suppress vibration of flexible dynamic systems. Input shaping is an efficient tool to eliminate transient and residual vibration caused by motion of these systems. This paper proposes a new formulation of the design method for multi-mode input shapers to eliminate residual vibration in flexible dynamic systems. The essence of the proposed method is to minimize the number of impulses to be n+1 for n-mode input shapers. This paper also suggests a solution procedure to solve the complex-valued nonlinear matrix equation for the input shapers. The proposed method is applied to two-mode input shapers. This paper discusses characteristics of several input shapers obtained under the same condition. Simulations and experiments show that the proposed method is very useful for designing multi-mode input shapers.

• Journal of Mechanical Science and Technology
• /
• 제16권9호
• /
• pp.1033-1039
• /
• 2002

Partial penetration welding joint refers to the groove weld that applies to the one side welding which does not use steel backing and to both side welding without back gouging, that is, the partial penetration welding joint leaves an unwelded portion at the root of the welding area. In this study, we analyzed the residual stress and fracture on the thick metal plates that introduced the partial penetration welding method. According to the above-mentioned welding method, we could draw a conclusion that longitudinal stress and traverse stress occurred around the welding area are so minimal and do not affect any influence. We also performed the fracture behavior evaluation on the partial penetration multi pass welding with 25.4 mm thick plate by using the J-integral, which finally led us the conclusion that the partial penetration multi-pass welding method is more applicable and effective in handling the root face with less than 6.35 mm.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.421-430
• /
• 2000

We apply the Rayleigh Ritz method to analyze multi-layered plates with residual stresses. The method is very simple, straight forward, and easily programmable, but it should be applied to structure s only in simple shapes. We derive coupled variational equations based on the principle of virtual displacement, and investigate what kind of basis functions is desirable for the analysis of rectangular plates with various boundary conditions. We demonstrate the effectiveness and usefulness of the method through several examples. The analysis results obtained with the method are in good agreement with those available in literature. A multi-layered MEMS plate example shows that the coupling effect should not be ignored and that residual stresses do influence the stiffness of the structure very much.

• 상하수도학회지
• /
• 제34권5호
• /
• pp.311-321
• /
• 2020

In this study, a model to optimize residual chlorine concentrations in a water supply system was developed using a multi-objective genetic algorithm. Moreover, to quantify the effects of optimized residual chlorine concentration management and to consider customer service requirements, this study developed indices to quantify the spatial and temporal distributions of residual chlorine concentration. Based on the results, the most economical operational method to manage booster chlorination was derived, which would supply water that satisfies the service level required by consumers, as well as the cost-effectiveness and operation requirements relevant to the service providers. A simulation model was then created based on an actual water supply system (i.e., the Multi-regional Water Supply W in Korea). Simulated optimizations were successful, evidencing that it is possible to meet the residual chlorine concentration demanded by consumers at a low cost.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1813-1819
• /
• 2001

Partial penetration welding Joint defines that groove welds without steel backing, welded from on side, and groove weeds welded from both sides but without back gouging, that is. it has an unwelded portion at the root of the weld. In this study we analysed fur residual stress and displacement distribution on partial penetration welding condition of thick plate metal. For 25.4mm thick plate, theoretical residual stress and displacement analysis by finite element method using ABAQUS was carried out and compared with the experimental result using hole-drilling method. In results of the condition of partial penetration, it appeared that longitudinal stress at welding area was a little difference and transverse stress did not have any effect by partial penetration multi-pass welding. From a point of welding distortion in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• 정보처리학회논문지:컴퓨터 및 통신 시스템
• /
• 제9권2호
• /
• pp.37-44
• /
• 2020

본 논문에서는 딥 러닝 기반의 전-자동 심장 분할 알고리즘을 제안한다. 본 논문에서 제안하는 딥 러닝 모델은 기존 U-Net에 residual recurrent convolutional block과 residual multi-dilated convolutional block을 삽입하여 성능을 개선한 모델이다. 모델의 성능은 테스트 데이터 세트를 전-자동 분할한 결과와 영상의학 전문가의 수동 분할 결과를 비교하여 분석하였다. CT 영상에서 평균 96.88%의 DSC, 95.60%의 precision과 97.00%의 recall 결과를 얻었다. 분할된 영상은 3차원 볼륨 렌더링 기법을 적용하여 시각화한 후 관찰하여 분석할 수 있었다. 실험 결과를 통해 제안된 알고리즘이 다양한 심장 하부 구조를 분할하기에 효과적인 것을 알 수 있었다. 본 논문에서 제안하는 알고리즘이 전문의 또는 방사선사의 임상적 보조역할을 수행할 수 있을 것으로 기대한다.

• 제어로봇시스템학회논문지
• /
• 제6권12호
• /
• pp.1045-1052
• /
• 2000

In this paper, we propose a method to apply the Input Shaping Technique (IST) to multi-input multi-output (MIMO) systems. In MIMO systems, there is a high possibility of multi-mode residual vibration. The IST filter designed for this multi mode may need a longer time to suppress the residual vibration. Previous works prove that we can shorten the time lag by using negative sequence. This negative sequence, however, causes another problem - it requires excessive control input. In this paper, we provide a remedy to reduce the size of control input by limiting the reference input by limiting the reference input and its derivative. The result of simulations and experiments on a 2 link flexible arm confirmed the effectiveness of the proposed method.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권9호
• /
• pp.495-501
• /
• 2000

This paper presents a method to minimize the initial deflection of a multi-layer piezoelectric microactuator without loosing its piezoelectric deflection performance required for light modulating micromirror devices. The multi-layer piezoelectric actuator composed of PZT silicon nitride and platinum layers deflects or buckles due to the gradient of residual stress. Based on the structural analysis results and relationship between process conditions and mechanical properties we have modified the fabrication process and the thickness of thin film layers to reduce the initial residual stress deflection without decreasing its piezoelectric deflection performance. The modified designs fabricated by surface-micromachining process achieved the 77% reduction of the initial deflection compared with that of the conventional method based on the measured micromechanical material properties is applicable to the design refinement of multi-layer MEMS devices and micromechanical structures.