• Korean Journal of Agricultural Science
• /
• v.38 no.3
• /
• pp.533-540
• /
• 2011

This study is to develop a mulit-layer glued columns for construction of Korean-style houses by using domestic small diameter logs. Dried small square lumber glued each other to develop a multi-layer glued columns and evaluated its performance of strength. Then, predicted the design load of multi-layer glued columns and make a comparison between actual load and design load of multi-layer glued columns. In the results, allowable load by allowable stress of multi-layer glued columns was measured one-third of actual columns load and prediction load was measured less than 10~30% of the actual load. Therefore, muilt-layer glued member has a standard allowable stress of compressive of 13 MPa (Larix leptolepis) and 19 MPa (Chamaecyparis obtusa) when used as columns. Also, using compression strength of small diameter square logs could calculate maximum loads of multi-layer glued member as column.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.1
• /
• pp.7-11
• /
• 2015

In this study, $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film were prepared on glass substrate by DC/RF magnetron sputtering method. To prevent interfacial reaction between Ag and ITO layer, Ti buffer layer was inserted. Optical properties and sheet resistance were studied depending on laminating times of each multi-layered film especially in visible ray. The simulation program, EMP (essential macleod program), was adopted and compared with experimental data to expect the experimental result. It was found out that the transmittance of the first stacked $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film was more than 90%. However, with increasing stacking times, the optical properties of $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film get worse. Consequently, Ti layer is good for oxidation barrier, but too many uses of this layer may have an adverse effect to optical properties of TCO film.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.29 no.1
• /
• pp.140-151
• /
• 2001

This study based on the theoretical understanding of multi-layer planting which have engineering, ecological and landscape benefits, was conducted to find out the status of multi-layer planting in the apartment and neighborhood park in Seoul. This study was also aimed to seek for the problematic matters, and suggest a solution on the current multi-layer planting. The results of this study were as follows; 1) Since landscape woody plants have been classified just as tree and shrub in Korea, the classification for the multi-layer planting has been unreasonable, and landscape woody plants might have been classified as tree, sub-tree and shrub, or upper, middle, and lower-layer, It could be defined that upper layer is over eight meters in full growth, middle over 3-8 meters and lower under 3 meters. 2) In apartments, the upper layer consisted of eighteen species, the middle and lower layer seven species each. In neighborhood parks, the upper layer consisted of fifteen species, and the middle and lower layer five species each. 3) In terms of planting year of the surveyed areas, there were no differences in the number of species when planting year of the apartment was divided into two groups, the first half(1900-1995) and the second(1996-2000). But, in terms of individual occupation, the percentage was decreased in upper layer, while there was increasing in middle and lower layer. 4) As the result of survey of multi-layered area, it appeared that apartment was shown 0.65 percent and neighborhood park 0.61 percent of the planted area, which was less than 1 percentage of landscape architecturally planted area. 5) In apartment, the number of individual in middle layers has been increased in the first half and the second, but with respect to the correlation with multi-layered area, the apartments had the "$\rho$=0.208", saying that increasing middle layer was scattered planting instead of multi-layered planting. 6) In planting at the apartments in Korea, the planting density was limited, because the layer division was restricted to only tree and shrub. On the contrary, it was divided into upper, middle and lower tree in Japan. Therefore, in Korea, it should be classified as the planting density by dividing into tree, sub-tree, and shrubs, or upper, middle and lower tree by the law. And, it should be considered that the multi-layered planting has a proper organic relation as well as the planting density.g density.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.832-836
• /
• 2003

Multi-layer ceramic composites were prepared by tape casting followed by hot pressing using silicon nitride layer with silicon nitride whiskers, silicon nitride layer with silicon carbide particles and boron nitride-alumina layer. The whiskers were aligned during the casting. As the whisker content of the silicon nitride layer was increased up to 10 wt％, the flexural strength of the multi-layer composite was increased. However, further increase of the whisker content in the layer resulted in a rapid decrease of the strength of the composite. The results suggest that the strength of multi-layer ceramic composite showing non-catastrophic failure behavior can be significantly improved by incorporating the aligned whiskers in the layers.

• Journal of Navigation and Port Research
• /
• v.30 no.8 s.114
• /
• pp.637-642
• /
• 2006

In this paper, we made an experiment on materials of two kinds. First, we made a study of Multi-layer EM wave absorbers using Sendust. In result, The bandwidth of the Multi-layer Sendust EM wave absorbers over 10 dB is extended in S-Band. Second, we investigated the mixing effects of AI(OH)3 on Multi-layer Sendust EM wave Absorbers. In result, the Multi-layer Sendust EM wave absorbers mixed with Al(OH)3 showed a extended bandwidth over 10 dB compared with non-mixed Multi-layer Sendust EM wave absorbers in S-Band.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.97-101
• /
• 2006

In this paper, Multi-layer EM wave absorbers using Sendust are presented. The bandwidth of the Multi-layer Sendust EM wave absorbers over 10 dB is extended in S-Band And we investigated the mixing effects of $Al(OH)_3$ on Multi-layer Sendust EM wave Absorbers. As a result, the Multi-layer Sendust EM wave absorbers mixed with $Al(OH)_3$ showed a extended bandwidth over 10 dB compared with non-mixed Multi-layer Sendust EM wave absorbers in S-Band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.3
• /
• pp.73-84
• /
• 2002

Fast and accurate new capacitance determination methodology for non-uniform complicated multi-layer VLSI interconnects is presented. Since a capacitance determination of intricate multi-layer interconnects using 3-dimensional field-solver is not practical, quasi-3-dimensional methodology is presented. Interconnects with discontinuity (i.e., bend structure and different spacing between lines, etc.) are partitioned. Then, each partial capacitance of divided parts is extracted by using 2-dimensional extraction methodology. For a multi-layer interconnects with shielding layer, the system can be simplified by investigating a distribution of charge in it. Thereby, quasi-3-dimensional capacitance for multi-layer interconnects can be determined by combining solid-ground based 2-dimensional capacitance and shielding effect which is independently determined with layout dimensions. This methodology for complicated multi-layer interconnects is more accurate and cost-efficient than conventional 3-dimensional methodology It is shown that the quasi-3-dimensional capacitance methodology has excellent agreement with 3-dimensional field- solver-based results within 5% error.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.302-308
• /
• 2018

Multi-Layer Sputtering is aim to develop desired thickness thin film multi-layer with different materials. The multi-layer thin film deposition process occupies a relatively large portion in the process time, because the main reason is that it takes much time to move the substrate to be deposited and to make the chamber into a high vacuum state compared to the process time. Most of semiconductor and display industries sputter a single substance in one chamber and move boards through multi-continuous robots to another chamber to sputter other materials. This will inevitably require multiple chambers, vacuum pumps, and multi-contamination robots within the process facility. To solve these problems, this paper proposes a control system for multi-layer thin film sputtering devices that deposit different materials within a single vacuum chamber and is applied in TFT process. The manufacture and experiment of the control system proved its validity.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.63-72
• /
• 2013

The main purpose of this study is to analyze the collection characteristics of multi-layer multi-stage porous plate system with ionizer and dielectric-substance experimentally. The experiment is carried out to analyze the characteristics of pressure drop and collection efficiency for the present system with experimental parameters such as applied voltage, inlet velocity, stage number and inlet particle concentration, etc. In results, for multi-layer multi-stage porous plate system of inflow type, at 5 stage and $v_{in}$=2.58 m/s, the pressure drop becomes lower 15 $mmH_2O$ as 95 $mmH_2O$ than that of non-inflow type system. It is estimated that for the present system with ionizer and dielectric-substance, the collection efficiency represents 98.5% showing higher 5.2% comparing to that of multi-layer multi-stage porous plate system without ionizer and dielectric-substance at 5 stage, $v_{in}$=2.58 m/s and inlet concentration $3g/m^3$(fly ash).

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.777-778
• /
• 2006

This paper deals with the optimum rotor design approach about the multi-layer design of the buried magnets in an Interior Permanent Magnet Synchronous Motor (IPMSM), on the efficiency improvement by using Response Surface Methodology (RSM). In the multi-layer design of the prototype 15kw IPMSM, the constant amount of buried PM is split from the single-layer into double-layer design for improving the efficiency characteristics. The optimum double-layer rotor structure is built with the help of RSM analysis. The improvement of IPMSM efficiency is verified by the Finite Element Method (FEM) results comparison with the prototype single-layer IPMSM.