• Journal of Sericultural and Entomological Science
• /
• v.14 no.1
• /
• pp.9-13
• /
• 1972

On the seventh day of mounting male and feamale cocoons are distinguished. A part of those male and female pupae is irradiated for 40 min. with 1,000r-ray irradiation. Those eggs obtained from the irradiated pupae are divided into six groups of 5, 15, 45, 90, 720 and 2,400 minutes after laying. The cahanges of accid soluble phosphorus in the each group of eggs are as follows. 1. In the control group of the maximum quantity in acid soluble phosphorus was 1,456r/100mg D.P. in the 2,400 minutes group, while the minimum quantity was 1,233r/100mg D.P. in the 720 minutes group. 2. In the mated group of ＊irradiated female moths and control male moths, the quantity of acid soluble phoshorus was small as compared with the control group in the five minute group of 1,288r/100mg D.P. and in the 15 minutes group of 1,299r/100mg D.P. while the quantity increased to 1,484r/100mg D.P. in the 45 minutes group. The quantity began to decrease again to 1,400r/100mg D.P. in the 2,400 minutes group which was smaller than that of the control group. The quantity was slightly small in the silkworm eggs laid in the early stage when compared with that of mated group of ＊irradiated male moths and control female moths. Both groups showed the larger quantity in the 720 minutes group than that of the control group. The quantity of acid soluble phosphorus in the mated group of control female moths .and ＊irradiated male moths was larger in variation than in the mated group of control male moths and ＊irradiated female moths. 3. In the mated group of ＊irradiated male and female moths the largerst quantity was 1,760r/100ms D.P. in 2,400 minutes group and second was 1,736r/100mg D.P. in 90 minutes group, and third was 1,288r/100mg D. P., in 5 minutes group. Generally the quantity was small in silkworm eggs laid by the irradiated one in the early stage than the control group, but in the later period of egg the quantity began to increase more than that of control group.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.4
• /
• pp.24-43
• /
• 2015

Since 2011, when Oegyujanggak Uigwe(Records of the State Rites of the Joseon Dynasty) were returned from France, which were looted in 1866 by the French Navy, national attention to our cultural properties abroad was explosively increased and public pressure has been mounting that those cultural properties should be returned in Korea. According to the statistics of "Overseas Korean Cultural Heritage Foundation" Korean cultural Properties, which exist in foreign countries, amounts 160,342 in total 20 countries. Among them about half of them are estimated to be illegally exported cultural property, these are to be restituted. However, in reality it is not so easy to restitute illegally exported cultural properties. For this, it needs to be established a long-term and systematic plan for return of cultural properties from other countries. This paper starts from such a critical mind and tries to find legal policy measures for the return of illegally exported cultural properties. To this end, the author first describes motive and aim of this research in chapter I. and overviews basic understanding and current situation of export of cultural property as well as means and methods of return of cultural property in chapter II. and then deals with international and national norms that are involved in the dispute concerned return of cultural properties in chapter III. Based on this research, in chapter IV., which can be considered as a key part of this paper, the author proposed nine legal policy measures for restitution of cultural properties from foreign countries. That is, actual condition survey of cultural properties in foreign countries, unified management and implement of export ID on cultural properties, fund-raising for the diversification of means of return of cultural properties. local utilization of cultural properties, joining in the multilateral conventions and expansion of the bilateral agreements, restitution and cooperation through international organizations, restitution through lawsuit and arbitration, training experts on restitution of cultural property and networking with foreign experts. Finally, the author summarized his opinion in chapter V. which comprehended researching the above.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.2
• /
• pp.4-21
• /
• 2018

This paper reviewed the legitimacy of the name of those sixteen pieces of hat artifacts known in Korean as pyeongjeongmo and currently housed by the National Palace Museum. This was undertaken in order to rectify the error of calling them pyeongjeongmo. Also, the paper suggested pyeongjeongmo's production method to apply representation of the artifacts or production of Joseon officials' hats as representation of ritual costumes in the royal court. The name pyeongjeongmo originated from pyeongjeonggeon. Gyeongguk Daejeon recorded that noksas wore yugak-pyeongjeonggeon and seoris wore mugak-pyeongjeonggeon, but the pyeongjeongmo artifacts housed in the National Palace Museum have been found irrelevant to those pyeongjeonggeons put on by both noksas and seoris. Rather, they has been confirmed as corresponding to dugeon or jogeon worn by byeolgams or suboks who served at the palace of the crown prince or princess. Through the investigation of the artifacts, the researchers could find out the tailoring and sewing methods, the finished look, and the folding manner of pyeongjeonggeon. Although the structure of pyeongjeonggeon was generally consistent, the frontal look was slightly different depending on the folding manner, resulting in three distinguished types of pyeongjeonggeon. Regardless, the pyeongjeongmo was made with one piece of fabric by a flat tailoring and folding method to create a three-dimensional hat. The finished shape appeared low in the front and high in the back side structure. The head girth was 55~59 cm, and the height was 19.4~21.5 cm. To make it with one piece of fabric, the head girth part was tailored in the same direction as the strands. Based on the artifact Changdeok 23820, this paper has also suggested a finished reproduction through the processes of preparing the materials, mounting, making the center ornaments, sewing and folding. The tailoring was completed with black silk fabric which was cut in a unique shape designed in advance, and hemp fabric which was mounted to the former. The top part of the head was finished with black threads, and the center line at the back was fixed with decolored cotton threads by blanket stitches with 3.5~4 cm intervals. Bamboo strands were inserted in the inside of the front-folded part, which then was fixed by patterned stitches with white cotton thread. At the back, a small bamboo clasp was attached so that one can lock it to the headband and prevent it from falling off.

• Science of Emotion and Sensibility
• /
• v.23 no.4
• /
• pp.105-116
• /
• 2020

The purpose of this study is to progress the limitations and disadvantages of existing safety clothing by applying high technology to current safety clothing that is produced and distributed only with fluorescent fabrics and retroreflective materials. Therefore, the industrial suspender-type safety belt and engineering technology are introduced, designed, and fabricated to help save a life in an emergency. First, the suspender-type safety belt to be developed is designed to emit light by LED attached to the film, and the body of the belt-wearer is recognized from a distance through retroreflection from the flashing LED. It aims to support people's safety by preventing accidents during roadside work, rescue activities, and sports activities at night. Second, with the development of advanced devices when the user is in an unconscious state due to distress or falls into an unconscious state due to distress or accident, the tilt sensor of the control unit attached to the belt automatically detects the angle of the human body and generates light and sound. It is intended to further enhance the utilization by mounting a sensing and signaling device that generates a distress signal and shaping it in the form of a belt attached to a vest that can be easily detached from the outside of the garment. When the wearer falls due to an accident, the tilt sensor of this belt detects the angle change and then the controller generates a high-frequency sound and repeated LED blinking signals at the same time. In the case of conventional safety vests, it is almost impossible to detect that the person is wearing a vest when there is no ambient light, but in case of the safety belts in this study, the sound and light signals of the safety belt enable us to find the wearer within 100 meters even when there is no ambient light.

• Economic and Environmental Geology
• /
• v.54 no.2
• /
• pp.233-245
• /
• 2021

Many studies on the microstructures in rocks have been conducted using experimental methods with various equipment as well as natural rock studies to see the development of microstructures and understand their mechanisms. Grain boundary migration of mineral aggregates in rocks could cause grain growth or grain size changes during metamorphism or deformation as one of the main recrystallization mechanisms. This study suggests improved ways regarding the analog material experiments with reformed equipment to see sequential observations of these grain boundary migration. It can be more efficient than the existing techniques and carry out an appropriate microstructure analysis. This reformed equipment was implemented to enable optical manipulation by mounting polarizing plates capable of rotating operation on a stereoscopic microscope and a deformation rig capable of experimenting with analog materials. The equipment can automatically control the temperature and strain rate of the deformation rig by microcontrollers and programming and can take digital photomicrographs with constant time intervals during the experiment to observe any microstructure changes. The composite images synthesized using images by rotated polarizing plates enable us to see more accurate grain boundaries. As a rock analog material, norcamphor(C7H10O) was used, which has similar birefringence to quartz. Static grain growth and simple shear deformation experiments were performed using the norcamphor to verify the effectiveness of the equipment. The static grain growth experiments showed the characteristics of typical grain growth behavior. The number of grains decreases and the average grain size increases over time. These case experiments also showed a clear difference between the growth curves with three temperature conditions. The result of the simple shear deformation experiment under the medium temperature-low strain rate showed no significant change in the average grain size but presented the increased elongation of grain shapes in the direction of about 53° regarding the direction perpendicular to the shearing direction as the shear strain increases over time. These microstructures are interpreted as both the plastic deformation and the internal recovery process in grains are balanced by the deformation under the given experimental conditions. These experiments using the reformed equipment represent the ability to sequentially observe changing the microstructure during experiments as desired in the tests with the analog material during the entire process.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_3
• /
• pp.1827-1836
• /
• 2022

Disasters that occur unexpectedly are difficult to predict. In addition, the scale and damage are increasing compared to the past. Sometimes one disaster can develop into another disaster. Among the four stages of disaster management, search and rescue are carried out in the response stage when an emergency occurs. Therefore, personnel such as firefighters who are put into the scene are put in at a lot of risk. In this respect, in the initial response process at the disaster site, robots are a technology with high potential to reduce damage to human life and property. In addition, Light Detection And Ranging (LiDAR) can acquire a relatively wide range of 3D information using a laser. Due to its high accuracy and precision, it is a very useful sensor when considering the characteristics of a disaster site. Therefore, in this study, development and experiments were conducted so that the robot could perform real-time monitoring at the disaster site. Multi-sensor module was developed by combining LiDAR, Inertial Measurement Unit (IMU) sensor, and computing board. Then, this module was mounted on the robot, and a customized Simultaneous Localization and Mapping (SLAM) algorithm was developed. A method for stably mounting a multi-sensor module to a robot to maintain optimal accuracy at disaster sites was studied. And to check the performance of the module, SLAM was tested inside the disaster building, and various SLAM algorithms and distance comparisons were performed. As a result, PackSLAM developed in this study showed lower error compared to other algorithms, showing the possibility of application in disaster sites. In the future, in order to further enhance usability at disaster sites, various experiments will be conducted by establishing a rough terrain environment with many obstacles.

• Journal of Internet Computing and Services
• /
• v.22 no.6
• /
• pp.25-32
• /
• 2021

In line with future changes in the marine environment, Aids to Navigation has been used in various fields and their use is increasing. The term "Aids to Navigation" means an aid to navigation prescribed by Ordinance of the Ministry of Oceans and Fisheries which shows navigating ships the position and direction of the ships, position of obstacles, etc. through lights, shapes, colors, sound, radio waves, etc. Also now the use of Aids to Navigation is transforming into a means of identifying and recording the marine weather environment by mounting various sensors and cameras. However, Aids to Navigation are mainly lost due to collisions with ships, and in particular, safety accidents occur because of poor observation visibility due to sea fog. The inflow of sea fog poses risks to ports and sea transportation, and it is not easy to predict sea fog because of the large difference in the possibility of occurrence depending on time and region. In addition, it is difficult to manage individually due to the features of Aids to Navigation distributed throughout the sea. To solve this problem, this paper aims to identify the marine weather environment by estimating sea fog level approximately with images taken by cameras mounted on Aids to Navigation and to resolve safety accidents caused by weather. Instead of optical and temperature sensors that are difficult to install and expensive to measure sea fog level, sea fog level is measured through the use of general images of cameras mounted on Aids to Navigation. Furthermore, as a prior study for real-time sea fog level estimation in various seas, the sea fog level criteria are presented using the Haze Model and Dark Channel Prior. A specific threshold value is set in the image through Dark Channel Prior(DCP), and based on this, the number of pixels without sea fog is found in the entire image to estimate the sea fog level. Experimental results demonstrate the possibility of estimating the sea fog level using synthetic haze image dataset and real haze image dataset.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.2
• /
• pp.136-146
• /
• 2023

Biological materials, such as stuffed specimens, can release various acids or volatiles. There has been no research carried out on the emission characteristics of organic compounds generated from the preservatives used in taxidermy specimens or associated manufacturing materials and methods. Therefore, in order to identify the organic compounds generated from taxidermy specimens, a degradation experiment was conducted on specimens for each material and for storage specimens. To produce Ogye chicken specimens, naphthalene and borax were used as preservatives, and planer sawdust, newspaper, and polystyrene foam were used as the core body materials. The deterioration experiment was conducted for 2 weeks in a high-temperature environment(50℃) and a high-humidity environment (95%), with an Ogye chicken specimen (year 2015) kept in an animal storage facility. Results indicated that the concentration of organic compounds generated by the specimen in the high-temperature environment tended to be greater than that in the high-humidity environment. The preservatives benzene, toluene, xylene, and p-dichlorobenzene were detected in the specimens using naphthalene, confirming that naphthalene is a major organic compound release factor, and the specimens that used sawdust, newspaper, and polystyrene foam also exhibited organic compounds. This appears to have been due to degradation of the material. In addition, ammonia was detected in the specimens for each material due to decay. In particular, the specimens using borax at high temperature were subject to approximately 9 times higher rates of ammonia-related deterioration than the specimens using naphthalene. These results can be considered to result from the prevention of biological damage through insecticidal effects by accelerating the sublimation of naphthalene in a high-temperature environment. Naphthalene is a potentially carcinogenic substance, and when used as a preservative, proper use management is required. Taxidermy specimens can release various organic compounds depending on the manufacturing techniques used, so a systematic preservation management plan is required that depends on conditions such as the applicable manufacturing materials and preservatives.

• Journal of Family Resource Management and Policy Review
• /
• v.27 no.2
• /
• pp.19-33
• /
• 2023

The purpose of this study is to explore the family diversity-related service experiences of Family Center practitioners under the main policy goal of recognizing family diversity set out in the Fourth Master Plan for Healthy Families. To this end, a focus group interview was conducted with 12 Family Center practitioners in multiple cities and districts who had extensive family service experiences. The focus group interview data were analyzed using thematic analysis. The analysis found that Family Center practitioners understood the concept of family diversity according to the changes in the family policy environment and applied it in various forms to the administration of their respective centers. However, while administering the family support services considering the aspect of family diversity, they experienced a lack of resources for various family service programs, conflicts between each family service goal and the family diversity-related program goal, and difficulties in identifying the recipients. To expand family diversity-related services in the future, the interviewees emphasized the need for education programs about family diversity targeted at Family Center practitioners, and family support services that reflect regional characteristics. They also stressed the need for changes in program operation methods, such as expanding family diversity education, and developing family service programs appropriate for diverse families. Lastly, they highlighted the need for mounting a publicity campaign for Family Centers, widening the target recipients of family programs, and expanding the budget for the administration of the family diversity project. The results of this study can serve as a basis for restructuring family services for the application and expansion of family diversity practices, and as educational material that can be used to strengthen the capacity of family service practitioners to plan and execute family support programs that take family diversity into consideration.