• Journal of the Korean Applied Science and Technology
• /
• v.14 no.1
• /
• pp.53-59
• /
• 1997

Spin finish(NSFs) for synthetic fiber were prepared. NSF-3 was proved to be the best spin finish by testing the properties and emulsion stability, etc. of NSFs. NSF-3 prepared by blending of spindle oil 70g, paraffin wax 10g, glyceryl mono-oleate 5g, POE(10) nonylphenyl ether 4g, POE(20) sorbitan tri-oleate 4g, Na-dioctyl sulfosuccinate 4g, antistatic agent 2g and water 1g was excellent in its characteristics. Optimum physical conditions of nylon filament treated with NSF-3 according to the number of revolution of oil roller were obtained at conditions of 5.5rpm in the number of revolution of oil roller, 1.21% of oil pick up, and denier 69.2D.

• Geotechnical Engineering
• /
• v.11 no.2
• /
• pp.107-120
• /
• 1995

The purpose of this study is to investigate the effects of fiber on engineering properties of Fiber-Reinforced Soil. Engineering properties of soil reinforced with discrete randomly oriented inclusion depend on soil density, particle size, grading, fiber length, tensile strength and stiffness of fiber, mixing ration of fiber, confining stress, etc.. in this paper, the influence of fiber shape, fiber length, fiber diameter, fiber content, cement content and curing duration on engineering characteristics(compaction, shear & permeability) were evaluated for typical soils produced from construction works through uniaxial compression tests and triaxial compression tests. From the experimental results, it was also investigated if there is an optimal range of fiber lengths and fiber contents for the tested soils and tested mono-filament fibers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.91-92
• /
• 2006

The important merit of Bi-2212/Ag wire is to apply cable as round wire state. Bi-2212 high Tc superconducting wires were fabricated in order to apply Rutherford cable near the future. Various Ag ratio from 0.22 to 0.42 of Ag tubes for PID (powder-In-Tube) process were used to investigate the workability and to prevent breakage of filaments during drawing. In order to find proper heat treatment condition, we investigated micro-structure of Bi-2212/Ag wires by using differential thermal analysis, XRD and SEM. The effect of atmosphere on the peritectic decomposition temperature of precursor was investigated. The shape of grain was observed by SEM to investigate Bi-2212 phase formation in filaments. The higher of Ag ratio of mono filament had the higher critical current density, Jc. The wire with 0.42 of Ag ratio showed 7,886 A/cm2 of Jc at 77K.

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.197-206
• /
• 2022

The purpose of this study was to confirm the optimal spinning conditions for PLA (Polylactic acid) as a fiber forming polymer. According to the melt spinning test results of PLA, the optimal spinning temperature was 258℃. However, it needs to note that relatively high pack pressure was required for spinning at 258℃. At an elevated temperature, 262℃, mono filament was broken easily due to hydrolysis of PLA at a higher temperature. In case of fiber strength, it was confirmed that the draw ratios of 2.7 to 3.3 were optimal for maximum strength of melt spun PLA. Above the draw ratio, 3.3, the strength of the PLA fibers was lowered. It was presumed that cleavage of the PLA polymer chain over maximum elongation. The heat setting temperature of GR (Godet roller) showed that the maximum strength of the PLA fibers was revealed around 100℃. The degree of crystallinity and the strength of the PLA fibers were decreased above 100℃. The optimal take-up speed (Spinning speed) was around 4,000m/min. Thermal analysis of PLA showed 170℃ and 57℃ as Tm (melting temperature) and Tg (glass transition temperature), respectively.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.1
• /
• pp.13-18
• /
• 1976

1) The variation of the reef knot strength $T_r$ and the trawler knot strength $T_\varrho$ with the angle $\varphi$ between the adjacent bars are given by $$T_r=T_{ro}-k_{r\varphi}$$ and $$T_\varrho=T_{{\varrho}o}+k_{\varrho\varphi}$$ where $T_{ro}$ and $T_{{\varrho}o}$ are values of $T_r$ and $T_\varrho$ at $\varphi=0^{\circ}$ respectively, and $k_r$ and $k_\varrho$ constants decided by the fibre materials of netting twines ($\varphi\;is\;0^{\circ}$ when the knot is pulled lengthwise). 2) The variation of the reef knot strength $T_r'$ and the trawler knot strength $T_\varrho'$ with the angle $\varphi'$ between any one bar and the plane made by the other three bars may be expressed by $$T_r'=T_{ro}{'}\varrho^{-c\varphi'}$$ and $$T_\varrho'=T_{{\varrho}o}{'}\varrho^{-c\varphi'}$$ where $T_{ro}{'}$ and $T_{\varrho}o{'}$ are values of $T_r{'}$ and $T_\varrho{'}$ at $\varphi'=0^{\circ}\;{(\varphi=45^{\circ})}$ respectively, and o is the coefficient of attenuation. 3) Knot strength of knotted netting may be expressed by the expression derived in the preyious paper, disregarding its shape and the direction of tensile loads acting on it.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.42 no.1
• /
• pp.1-10
• /
• 2006

Present study was conducted to improve the spring frame net trap for conger eel, Conger myriaster which prevents by-catch and protects immature fish. A series of comparative fishing experiment was carried out in water off the south-east coast of Korea from Nov. 2004 to Jul. 2005. And analyzed the amount of catch, by-catch rate, and CPUE, etc. of experimental traps which were the spring frame net traps, sorted four types of flappers. And the compared gear was a plastic conger eel pot. The conclusions were as follows. By-catch rates of spring frame net trap with the compressed flapper bound by nylon mono-filament was about 0-3%. CPUE of spring frame net trap with the compressed flapper was about 50-60% lower than that of traditional and plastic pot. And in case of conger eel that the total length is over 350mm, CPUE was little different on each type of flapper of every mesh size.

• Ocean and Polar Research
• /
• v.40 no.3
• /
• pp.169-176
• /
• 2018

Recently, the pop-up satellite archival tag (PSAT) is being used in studies as a method of using satellites for monitoring organisms. Because PSATs are attached directly on the organism being monitored, it is used mostly on larger species since the health of the organism is an important concern. For this reason, PSAT-based surveys are lacking in Korea with no studies on the physiological responses of organisms with PSAT attached. Accordingly, as a basic biomonitoring study using PSAT, the present study investigated the physiological changes in fish in response to the attachment of PSAT. The present study used red seabream (Pagrus major) and Korean rockfish (Sebastes schlegelii) as the experimental fish. The PSAT was attached to the muscle below the experimental fish's dorsal fin using a mono filament (n = 3). To investigate the changes in physiological responses according to PSAT attachment, blood samples were collected from all experimental fish, including the control (n = 3), at 1, 7, 14 and 21 days after the attachment. Upon blood sample collection, whole blood was used to measure hematocrit and hemoglobin levels. After separating the plasma, the separated plasma was used to measure the GOT, GPT, glucose, total protein, and cholesterol levels. Meanwhile, the plasma cortisol, superoxide dismutase, and catalase levels were measured using the ELISA method. The results showed that attaching the tag did not have any impact on the immunity and stress response of the experimental fish. The findings in this study also demonstrated the possibility of using PSAT for studying relatively smaller species living in the coastal waters of Korea.

• Fashion & Textile Research Journal
• /
• v.23 no.2
• /
• pp.290-296
• /
• 2021

The effect of draw ratio (8, 10, 12, 14 times) and additive CaCO₃ content (0, 0.5, 1.0, 1.5, 2.0, and 3.0 wt%) on the properties of high-performance PE monofilament was investigated in this study. As the draw ratio increased (8-14 times), the melting enthalpy (ΔHf), crystallinity, specific gravity, and tensile strength increased significantly. However, the draw ratio had little effect on the melting temperature (Tm) and crystallization temperature (Tc). The seawater fastness (stain and fade) of the hydrophobic PE monofilament prepared in this study showed an excellent grade of 4-5 in all draw ratios. To investigate the effect of the additive CaCO₃ content on the properties of high-performance PE monofilament, the draw ratio was fixed at 14 times. It was found that the tensile strength of the PE monofilament sample containing 0.5 wt% of CaCO₃ was much greater compared to the sample without CaCO₃, but the elongation of the sample containing 0.5 wt% of CaCO₃ was much less than the sample with 0 wt% CaCO₃. However, in the case of the sample containing more than 0.5 wt% CaCO₃, the tensile strength slightly decreased and the elongation slightly increased as the CaCO₃ content increased. The seawater fastness (stain and fade) of the hydrophobic PE monofilament showed excellent grades of 4-5, regardless of the amount of additives. From the above results, it was found that the maximum draw ratio of 14 times with an additive of 0.5 wt% CaCO₃ are the optimal conditions for manufacturing high-performance marine fusion materials with various fineness (denier) with high strength and low elongation.