• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.857-862
• /
• 2014

In this paper, we designed and fabricated electromagnetic induction based scaffold type energy harvester. For energy harvesting, mechanical energy of vertical motion is transferred to rotational energy using rack gear and multiplying gear was used to maximize energy transfer. To optimize design parameters, physical structure of energy harvester was modeled using finite element method. The effect of multiplying gear ratio and frequency levels of applied mechanical energy on energy generation efficiency are analyzed by computer simulation and experimental test. Experimental results showed that maximum 25.36 W of electric power can be achieved at the frequency of 2 Hz and 1:77 of gear ratio with only 5 mm of vertical changes on scaffold structure.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.682-685
• /
• 2021

The design and fabrication of LTE Cat.M1 (3GPP Release13 Standardization) modules of ships such as fishing boat and patrol boat are reported in this research. LTE cat.M1 modules are needed to expand the for broadening of IoT services through the ships used in fishing gear automatically identification monitoring system, which is one of applying ICT into the real name system of electric fishing gear.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.38-45
• /
• 2004

As optical communication is being substituted for telecommunication, the demand of a large variety of fiber optic components is increasing. V-groove substrates, one of the module components, are used to connect optical fibers to optical planar circuits and to arrange fibers. Their applications are multi-channel optical connectors and optical waveguide fiber coupling, etc. Because these substrates are a critical part of the splitter in a multiplexer and a multi fiber connector, precise and reliable fabrication process is required. For precisely aligning core pitch between fibers, machined core pitch tolerance should be within sub-microns. Therefore, these are generally produced by state-of-the-art micro-fabrication like MEMS. However, most of the process equipment is very expensive. It is also difficult to change the process line for custom designs to meet specific requirements using various materials. For various design specifications such as different values of the V angle and low-priced process, the fabrication method should be flexible and low cost. To achieve this goal, we have suggested a miniaturized machine tool with high accuracy positioning system. Through this study, it is shown that this cutting process can be applied to produce V-groove subtracts. We also show the possibility of using a miniaturized machining system for producing small parts.

• Journal of KIBIM
• /
• v.9 no.3
• /
• pp.8-18
• /
• 2019

Precast concrete manufacturing has proved economies of scale through the repetitive production by means of standardization, automation, and prefabrication. Advanced digital design and fabrication technologies can empower its benefits by enabling mass customization in the building design and construction. This study analyzed five case studies in terms of 1) design intent and background, 2) module development and facade construction, 3) integrated process among project stakeholder. This article has attempted to establish the following three points in conclusion: 1) Form generating digital design tools such as Rhino, CATIA, Generative Component, and Digital Project were implemented to produce parametric surface pattern and rationalization to maximize existing precast manufacturing benefits. Also, BIM program has been used to promote coordination and communication among engineering consultants and contractors, 2) In addition to traditional precast concrete materials, GFRC, RFP, brick cladding precast and 3D printed mould have been introduced to reduce the weight and cost and to comply the code from the zoning, seismic, and fireproof requirements, 3) Design-assist contract, design-assist financial support, and co-location measures have been introduced to facilitate collaboration between architect, fabricator, and contractor from the beginning of the project.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.5 no.1 s.9
• /
• pp.13-19
• /
• 2006

In this paper, a broadband Microwave Power Module(MPM) operating at 7 - 11 GHz is designed and fabricated. The MPM consists of a SSA (Solid State Amplifier) and a conventional TWT (traveling Wave Tube). This combined module takes advantage of a low noise and high gain of SSA. The computer modeling and simulation of the SSA are designed by the use of the ADS (Advanced Design System) software. The SSA is designed by configurating the CSSDA (Cascaded Single Stage Distributed Amplifier). The broadband MPM is measured to be noise figure 8.3 - 10.02 dB at 7 - 11 GHz bandwidth, output power of 38.12 dBm at 9 GHz.

• Journal of Advanced Navigation Technology
• /
• v.10 no.1
• /
• pp.26-33
• /
• 2006

This paper discusses the design and fabrication of a wireless VHF receiver for use in air traffic control. The VHF receiver was designed and tested in three modules: a control module, a receiver module and a power module, all of which were integrated into a single block for final testing. The fundamental performance of the receiver, and in particular, sensitivity, the most important factor, is designed to satisfy existing commercial wireless transmitter specifications for air traffic control. The receiver displays a sensitivity of -113 dBm, which is higher performance than existing commercial products, and is suitable for use as a basic component of CNS/ATM.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.1217-1219
• /
• 2003

상용화되어 있는 이동통신 기기의 Front-end 부분은 듀플렉서와 필터를 포함하는 수동소자로 구성되어 있다. 듀플렉서의 임피던스 정합선로는 전송선로 이론으로부터 설계하며, 단순하게 ${\lambda}=1/4$ 파장 길이의 정합 선로를 설치하는 것이기 때문에 정합선로를 이용한 듀플렉서 성능을 극대화하기 위한 설계의 융통성이 없는게 현실이다. 이런 문제점을 해결하기 위하여 집중소자(lumped element)인 R L C를 탄성 표면파 듀플렉서 대신 스위치 모들에 적용하게 된다면 여러 가지 다양한 형태의 회로를 구현할 수 있고 회로망 내에 위치하는 집중소자의 정격을 최적화하여 스위치 모듈의 성능을 향상시킬 수 있는 가능성이 있다. 본 연구에서는 $900 MHz{\sim}2.2 GHz$의 대역에서 소형화 집적화에 적용 가능한 디바이스를 개발하기 위하여 고주파, 저진압, 저손실 스위치 모듈의 제조와 구성되는 커패시터와 인덕터의 제조와 특성에 관하여 연구하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.347-348
• /
• 2008

The main goal of this work is advances in 1.0mm $\times$ 0.5mm light emitting diode using AlInGaN cell structure and display module. In the first place, we proposed $200{\mu}m{\times}200{\mu}m$ cell structure using AlInGaN. Secondly, we describe new type 1.0mm $\times$ 0.5mm blue and white LED fabrication procedure and results of an examination include mobile application.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1B
• /
• pp.175-182
• /
• 2000

(A hybrid-type wireless infrared data communication module was fabricated by using the light emitting andabsorption diodes with the one-chip of integrated digital circuits. The light emitting diode with the peak spectrum of 850 nm was made from compound semiconductor material of AIGaAs and shows high speed signal transmission with the delay time of 60 nsec for the light direction angle of 30". The Si PIN photodiode showsthe good absorption rate for the range of wavelength of 450-1050 nm and convex-type epoxy lens was utilized for the spectrum filtering on the visible-range spectrum below 750 nm, The data transmission speed is 115.2 kbps and the fabricated module satisfies on the IrDA 1.0 SIR standard requirements.)ments.)

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.19-25
• /
• 2000

In this paper, we describe RF receiver module for IMT-2000 handset with 5 MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier, RF SAW filter, Down-converter, If SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8 dB, 3 dBm at 2.14 GHz, conversion gain of down-converter is 10 dB, dynamic range of AGC is 80 dB, and phase noise of PLL is -100 dBc at 100 kHz. The receiver sensitivity is -110 dBm, adjacent channel selectivity is 48 dBm.