• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.84-91
• /
• 2001

Comparison between performance of a plate fin and that of a modified plate fin is investigated as a function of the position, the non-dimensional width and height of wings as well as the non-dimensional fin length using a two-dimensional separation of variables method. The ratio of the incremental rate of heat loss to that of the area of a modified plate fin is also presented as a function of the height of wings. The modified plate fin is made by attaching the wings to upper and lower sides of a plate fin. One of the results shows that performance of a modified plate fin is more improved as the wings approach left (higher) thermal reservoir.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.465-468
• /
• 2006

This paper investigates the effect of curing conditions on the strength improvement of polymer-modified mortars using epoxy resin with various curing methods. The polymer-modified mortars using epoxy resin are prepared with various polymer-cement ratios, and subjected to standard, hot water, heat cure and autoclave cures. The epoxy-modified mortars are tested for flexural and compressive strengths at desired curing methods. From the test results, the flexural and compressive strengths of the epoxy-modified mortars are hardly improved by the autoclave and hot water cures compared to the ideal cure of $20^{\circ}C$. Among the four types of curing methods, the strengths of the heat cured epoxy-modified mortars is largely improved. Especially, it is obtained in the mortars sealed with PVDC film.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.332-333
• /
• 2013

This research utilizes the modified sulfur having the low melting point which 65℃ is tries to study the strength property of the mortar according to the cure method of the modified sulfur mortar. And we try to use as basic data for investigating the curing condition of the light panel optimum utilizing the modified sulfur. We experimented by five kinds; 20℃ water curing method and 20, 40, 60, 80(℃) air dry curing method. In 3 day curing, the compressive strength was improved caused by high curing temperature. But the compressive strength was degraded caused by enhanced temperature in 7day curing and 28day curing. Therefore, the curing temperature of the modified sulfur mortar is determined that it comes 20 time case curing and the water curing is the most recommendable.

• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1541-1558
• /
• 2023

The new Modified-690Gd alloy, namely as Ni-30Cr-(10-x) Fe-xGd (x = 0.5, 1.0, 1.5,2.0, 3.0 wt%) for function structure integrated thermal neutron shielding has been prepared and characterized. The Modified-690Gd alloy was mainly composed of γ austenite matrix and (Ni, Cr, Fe)₅Gd precipitated along grain boundaries. The new Modified-690Gd alloy had great mechanical properties, which had the tensile strength exceeding 620 MPa and the elongation being above 50%. Meanwhile, this alloy had excellent weldability and good corrosion resistance in boric acid. The new Modified-690Gd alloy is expected to be a kind of high efficiency thermal neutron shielding materials.

• Honam Mathematical Journal
• /
• v.46 no.2
• /
• pp.279-290
• /
• 2024

In this study, tubular surfaces were introduced according to the modified orthogonal frame defined at the points where the torsion is different from zero in the 3-dimensional Euclidean space. First, the relations between the Frenet frame and the modified orthogonal frame with torsion are given. Then, the singularity, Gaussian curvature, mean curvature and basic forms of the tubular surface given according to the modified orthogonal frame with torsion were calculated. In addition, the conditions for the parameter curves of the tubular surface to be geodesic, asymptotic and line of curvature were examined. Finally, tubular surface examples based on both the Frenet frame and the modified orthogonal frame with torsion were given to support the study.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.16 no.1
• /
• pp.96-101
• /
• 2012

Purpose: Glomerular filtration rate is an important index for assessment of renal function, early discovery of renal disease, and progress observation of chronic renal disease patients. In the present study, the objective is to conduct a comparative analysis of differences between Gates and Modified Gates method in dynamic renal scintigraphy based on MDRD (Modification of Diet Renal Disease) formula using blood collection. Materials and Methods: Renal scintigraphy was performed for 45 patients who visited our hospital between November 2010 and August 2011. For 20 patients of those tested, glomerular filtration rates from Gates method and MDRD formula using AGUS equipment, were compared. For the other 20 patients, glomerular filtration rates from Modified Gates method and MDRD formula using INFINIA equipment. Finally, Gates and Modified Gates method were compared for 5 patients who indicated no change in glomerular filtration rates from MDRD formula during progress observation. Results: Glomerular filtration rates from both Gates and Modified Gates method showed a high correlation with those from MDRD formula ($p$<0.01, r=0.903, r=0.867), with a paired difference mean for Gates method of $2.05{\pm}2.54mL/min/1.73m$, and that for Modified Gates method of $25.2{\pm}3.71mL/min/1.73m$. Finally, the values for Gates method and those for Modified Gates method showed a high correlation for the five patients ($p$<0.05, r=0.949), with a paired difference mean of $20.4{\pm}8.84mL/min/1.73m$. Conclusion: Glomerular filtration rates from Gates method, Modified Gates method and MDRD formula showed mutually high correlations. If the tests are performed with recognition for the correlations between Gates and Modified Gates method used in a dynamic renal scintigraphy, then an accurate assessment of renal function is considered possible with an improved diagnostic ability.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.1024-1030
• /
• 1996

• Korean Journal of Agricultural Science
• /
• v.45 no.1
• /
• pp.28-37
• /
• 2018

This study was done to develop environmental risk assessments and a biosafety guide for insect-resistant genetically modified rice at a LMO (Living Modified Organism) isolation field. In the LMO quarantine area of Kyungpook National University, the species diversities and population densities of non-target insects found on insect-resistant genetically modified rice (Bt-9) resistant to Cnaphalocrocis medinalis and on non-GM rices (Dongjin and Ilmi) were investigated. The Bt-9 event was therefore evaluated under field conditions to detect possible impacts on the above ground insects and spiders. The study compared transgenic rice and two non-GM reference rices, Ilmi and Dongjin, at Gunwi in Southern Korea in 2016. Each rice was grown on three $18m^2$ plots with a randomized block design. A total of 4,243 individuals from 43 families and 9 orders were collected from the LMO isolation field. In the three types of rice fields, a total of 1,467 individuals from the insect-resistant genetically modified rice (Bt-9), 1,423 individuals from the Ilmi, and 1,353 individuals from the Dongjin were collected, respectively. There was no difference between the population densities of the non-target insect pests, natural enemies and other insects on the insect-resistant genetically modified rice (Bt-9) and non-GM rices. These results provide the diversity and population density of non-target insects for an environment risk assessment survey on insect-resistant genetically modified rice and could be used as a guideline to make a biosafety assessment method for genetically modified crops.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.613-630
• /
• 2006

Nucleic acids are virtually omnipresent; they exist in every living being. These macromolecules constitute the most important genetic storage material: the genes. Genes are conserved throughout the evolution of all living beings; they are transmitted from the parents to their offspring. Many interdisciplinary research groups are interested in modifying nucleic acids for use in a wider variety of applications. These modified oligonucleotides are used in many diverse fields, including diagnostics, detection, and therapeutics. In this account, we summarize our research efforts related to modified nucleic acid systems. First, we discuss our syntheses of modified oligonucleotides containing fluorescent tags for use as molecular probes (molecular beacons) to detect single-nucleotide polymorphisim (SNP) in nucleic acids and to distinguish between the B and Z forms of DNA. We also describe our research efforts into oligonucleotides functionalized with steroid derivatives to enhance their cell permeability, and the synthesis of several calix[4]arene-oligonucleotide conjugates possessing the ability to form defined triplexes. In addition, we have performed systematic studies to have an understanding about the functional groups necessary for a given nucleoside to behave as an organo or hydrogelator. The aggregation properties of a number of nucleoside-based phospholipids have been examined in different solvents; some of these derivatives are potential candidates for use as nucleoside-based liposomes. Finally, we also describe our research efforts toward the preparation of isoxazole- and isoxazoline-containing nucleoside derivatives and the determination of their antiviral activities.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.133-138
• /
• 2013

Acrylonitrile-butadiene-styrene (ABS) plastic is a polymer material extensively used in electrical and electronic applications. Nickel (Ni) thin film was deposited on ABS by electroless plating, after its surface was treated and modified with atmospheric plasma generated by means of dielectric barrier discharges (DBDs) in air. The method in this study was developed as a pre-treatment for electroless plating using DBDs, and is a dry process featuring fewer processing steps and more environmentally friendliness than the chemical method. After ABS surfaces were modified, surface morphologies were observed using a scanning electron microscope (SEM) to check for any physical changes of the surfaces. Cross-sectional SEM images were taken to observe the binding characteristics between metallic films and ABS after metal plating. According to the SEM images, the depths of ABS by plasma are shallow compared to those modified by chemically treatment. The static contact angles were measured with deionized (DI) water droplets on the modified surfaces in order to observe for any changes in chemical activities and wettability. The surfaces modified by plasma showed smaller contact angles, and their modified states lasted longer than those modified by chemical etching. Adhesion strengths were measured using 3M tape (3M 810D standard) and by 90° peel-off tests. The peel-off test revealed the stronger adhesion of the Ni films on the plasma-modified surfaces than on the chemically modified surfaces. Thermal shock test was performed by changing the temperature drastically to see if any detachment of Ni film from ABS would occur due to the differences in thermal expansion coefficients between them. Only for the plasma-treated samples showed no separation of the Ni films from the ABS surfaces in tests. The adhesion strengths of metallic films on the ABS processed by the method developed in this study are better than those of the chemically processed films.