• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.894-906
• /
• 2019

In this paper, a DC-DC converter is proposed based on the Cuk converter. The proposed converter has high efficiency and it can be used in multilevel DC-DC converters. A reduction of the inductors size in comparison to Cuk converter and a reduction in the inductors resistance negative effects on efficiency are the important points of the proposed converter. Its voltage ripple is reduced when compared to other converters. Its output voltage has a high quality and does not contain spikes. A theoretical analysis demonstrates the positive points of the proposed converter. The design and analysis of the converter are done in continues conduction mode (CCM). Experiments confirm the obtained theoretical equations. The proposed converter voltage gain is similar to that of a conventional Boost converter. As a result, they are compared. The comparison illustrates the advantages of the proposed converter and its higher quality. Furthermore, a prototype of the proposed converter and its combination with a 2x multiplier are built in the lab. Experimental results validate the analysis. In addition, they are in good agreements with each other.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.537-538
• /
• 2008

A step-down DC-DC converter with On-chip Compensation for battery-operated portable electronic devices which are designed in 0.18um CMOS standard process. In an effort to improve low load efficiency, this paper proposes the PFM (Pulse Frequency modulation) voltage mode 1MHz switching frequency step-down DC-DC converter with on-chip compensation. Capacitor multiplier method can minimize error amplifier compensation block size by 20%. It allows the compensation block of DC-DC converter be easily integrated on a chip and occupy less layout area. But capacitor multiplier operation reduces DC-DC converter efficiency. As a result, this converter shows maximum efficiency over 87% for the output voltage of 1.8V (input voltage : 3.3V), maximum load current 500mA, and 0.14% output ripple voltage. The total core chip area is $mm^2$.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.93-101
• /
• 2016

A new four-primary-switch diode clamped soft switching three-level DC-DC converter (TLDC) with full zero-voltage switching (ZVS) load range and TL secondary voltage waveform is proposed. The operation principle and characteristics of the presented converter are discussed, and experimental results are consistent with theoretical predictions. The improvements of the proposed converter include a simple and compact primary structure, TL secondary rectified voltage waveform, wide load range ZVS for all primary switches, and full output-regulated range with soft switching operation. The proposed converter also has some disadvantages. The VA rating of the transformer is slightly larger than that of conventional TLDCs in variable input and constant output mode. The conduction loss of the primary coil is slightly higher because an air gap is inserted into the magnetic cores of the transformer. Finally, the secondary circuit is slightly complex.

• International journal of advanced smart convergence
• /
• v.8 no.4
• /
• pp.138-146
• /
• 2019

In this paper, we proposed a soft-switched synchronous buck converter, which can perform charging the battery. The proposed converter has low switching loss even at high frequency operation due to its soft switching characteristics. The converter operates in synchronous mode to minimize conduction loss, resulting in small conduction loss, also. In this reason, the efficiency of the converter can be greatly improved even in high frequency. The size and weight of the converter can be reduced by high frequency operation of the converter. In this paper, we designed a battery charger with a switching frequency of 100 kHz. The designed converter also simulated to prove the converter's characteristics of synchronous operation as well as soft switching operation. The simulation shows that the proposed converter always meets the soft switching conditions of turning on and off switching in the zero voltage and zero current states. Therefore, simulation results have confirmed that the proposed battery charger had soft switching characteristics. The simulation results for transient response to charge current for the designed converter show that the converter responds to charge current commands quickly within 0.05 ms.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.4
• /
• pp.14-19
• /
• 2010

In this paper, using interleaved power factor correction how to improve the inverter efficiency studied. Interleaved method can reduce the conduction losses and the inductor energy. Generally, critical conduction mode (CRM) boost PFC converter used low power level because of the high peak currents. if you use the interleaved mode, CRM PFC can be used medium or high power application. interleaved CRM PFC can reduce current ripple for higher system reliability and size of buck capacitor and EMI filter size. Interleaved CRM PFC that is installed in front of inverter can maintain the constant voltage regardless of the input voltage.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.240-249
• /
• 2018

Individual DC voltage balance problem is an inherent issue for cascaded H-bridge (CHB) based converter. When the CHB-based static synchronous compensator (STATCOM) is operating at zero current mode, the software-based individual DC voltage balancing control techniques may not work because of the infinitesimal output current. However, the different power losses of each cell would lead to the individual DC voltages unbalance. The uneven power losses on the local supplied cell-controllers (including the control circuit and drive circuit) would especially cause the divergence of individual DC voltages, due to their characteristic as constant power loads. To solve this problem, this paper proposes an adaptive voltage balancing module which is designed in the cell-controller board with small size and low cost circuits. It is controlled to make the power loss of the cell a constant resistance load, thus the DC voltages are balanced in zero current mode. Field test in a 10kV STATCOM confirms the performance of the proposed method.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.4
• /
• pp.183-190
• /
• 2003

We report the performance of an open-frame type low-voltage high-current DC-DC converter module developed using an active clamp forward converter circuit and current doubler rectifier. The converter module is designed with the specifications of an 1.8V output voltage, 25A output current, and 36-75V input voltage. The synchronous rectifier is used to reduce the conduction fuss at high current level and current-mode control is adapted to enhance the flexibility in the system configuration. A prototype converter module is successfully implemented within 10mm height and half brick size (58${\times}$61mm), and recorded an 84% efficiency and 4% voltage regulation for the entire input voltage range, thereby demonstrating its application potentials to future telecommunication electronics.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.4
• /
• pp.183-183
• /
• 2003

We report the performance of an open-frame type low-voltage high-current DC-DC converter module developed using an active clamp forward converter circuit and current doubler rectifier. The converter module is designed with the specifications of an 1.8V output voltage, 25A output current, and 36-75V input voltage. The synchronous rectifier is used to reduce the conduction fuss at high current level and current-mode control is adapted to enhance the flexibility in the system configuration. A prototype converter module is successfully implemented within 10mm height and half brick size (58×61mm), and recorded an 84% efficiency and 4% voltage regulation for the entire input voltage range, thereby demonstrating its application potentials to future telecommunication electronics.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.1
• /
• pp.10-17
• /
• 2002

Due to the development of information communication field, the interest of the SMPS(Switched Mode Power Supply) is increased. The size and weight of SMPS are decided by inductor, capacitor and transformer. Thus, the low loss converter which is operated in high speed switching is required. The resonant FB DC-DC converter is able to operate in high speed switching and apply to high power field because the switching loss is low. In this thesis, it is proposed to control strategy for constant output power of resonant FB DC-DC converter in variable input voltage. The proposed control system is a digital I-PD type control and apply to phase-shift resonant type controller. The output voltage tracks reference without steady state error in variable input voltage. The validity of proposed control strategy is verified from results of simulation and experiment.

• Journal of IKEEE
• /
• v.18 no.3
• /
• pp.320-327
• /
• 2014

Recently, Importance of power management circuit technology is increased with the development of portable electric devices. This paper presents a high performance DC-DC buck converter for mobile applications. Especially, presented design have low ripple voltages and driving capability of large load current. A designed voltage mode 2-phase DC-DC converter is implemented in a $0.35{\mu}m$ CMOS process, and the overall size is $2.35{\times}2.35mm^2$. The peak efficiency is 91% with a 4MHz frequency and the maximum load current is 4A.