• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.407-408
• /
• 2017

In regenerative mode of an IPMSM control system without a bi-directional DC-DC converter, the 3-phase PWM inverter charges the battery. At this time, the regenerative torque reference for braking must output the proper torque reference to charge the battery. This paper proposed a regeneration control method that controls the voltage and current of the battery through CC-CV control at the regenerative braking torque corresponding to the driver's brake control.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.57-61
• /
• 2002

This paper presents a current-source-inverter based on a buck-boost configuration and its application for residential photovoltaic system. The proposed circuit has five switches. Among them, only one switch acts as chopping, and the other determine the polarity of output; therefore, it can reduce the switching loss. Because the input inductor current is operated on the discontinuous conduction mode, high power factor can be achieved without additional input current controller. So the overall system shows a simple structure. The operational modes are analysed in depth, and then it was verified through the experimental results using a 150 W prototype.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1078-1080
• /
• 2003

This paper proposes the boost input type resonant power supply for driving the magnetron device of the high-capacity microwave oven. Circuit topology of the proposed power supply is the boost input type resonant converter which uses the resonance between transformer leakage inductance and resonance capacitance. Proposed power supply obtains high power factor more than 98% through continuous current mode pulse width modulation. To verify the validity of the proposed power supply, operation principle in the steady state is analyzed and experimental results are presented.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1211-1213
• /
• 2003

A pulse width modulation(PWM) method for single-phase Sepic-type rectifier is introduced in this paper. The characteristics of the proposed PWM system are high performance high power factor with low input current harmonic distortion. The proposed control method is based on the average-current-mode using the dedicated integrated circuit UC3854 this technique it is possible to implement a very simple control circuit for unitary power-factor in CCM operation and also to provide over-current protection.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.152-155
• /
• 2009

In high power application, PFC(Power Factor Correction) pre-regulators are generally required. PFC pre-regulators could achieve unity power factor, reduce line input current harmonics and utilize full line power. Interleaving PFC converters could reduce input ripple current, output capacitor ripple current and inductor size. With this closed loop interleaving method, both two phase converters are working at the boundary between continuous and discontinuous mode and accurate 180 degree phase shift is achieved. Implementation of this strategy could be easily integrated to the control chip. Finally, experimental results of a two-phase interleaved boost PFC are presented to verify the discussed features.

• Journal of the Korean Society of Safety
• /
• v.20 no.3 s.71
• /
• pp.47-52
• /
• 2005

Recently, power conversion equipment increased rapidly makes a lot of harmonics. Thus, it is growing that wrong operation and break down of sensitive devices. There are two kinds of causes of harmonics. One of them is lots of power conversion equipment as modem controller, inverter, converter and SWS(Switching Mode Power Supply). Another is nonlinear operating machines as transformer and motor. The more nonlinear loads like them grow, the more serious problems as harmonic current to source and low power factor because of increasing reactive power grow. It is installed for reactor and L-C Filter to decrease harmonic in general. This paper analysis and compares two of characteristics and harmonic from reactor and L-C Filter with operation of induction motor and power conversion equipment. In the result, L-C Filter more improves unbalance rate and THD than reactor.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.224-226
• /
• 2008

본 논문에서는 매트릭스 컨버터로 구동되는 유도전동기의 속도제어 성능을 향상시키기 위한 적응제어 기법을 제안한다. 유도 전동기는 비선형적 마찰력 등으로 인한 비선형적 특성을 가진다. 이러한 비선형적 특성으로 인해 야기되는 왜곡을 보상하고 속도제어 성능을 개선하기 위해 슬라이딩 모드 제어 기법을 적용한다. 슬라이딩 모드에서 발생하는 채터링 현상과 모델링되지 않은 유도 전동기의 불확실성에 의한 제어 성능 저하를 개선하기 위해, 불확실성 추정을 위한 퍼지 기반 불확실성 추정기를 적용한다. 시뮬레이션을 통해 제안한 제어기법의 타당성을 검증한다.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.367-368
• /
• 2014

This paper investigates characteristics of high power semiconductor device losses in 5MW-class Permanent Magnet Synchronous Generator (PMSG) Medium Voltage (MV) wind turbines. High power semiconductor device of press-pack type IGCT of 6.5kV is considered in this paper. Analysis is performed based on neutral point clamped (NPC) 3-level back-to-back type voltage source converter (VSC) supplied from grid voltage of 4160V. This paper describes total loss distribution at worst case under inverter and rectifier operating mode for the power semiconductor switches. The loss analysis is confirmed through PLECS simulations. In addition, the loss factors due to di/dt snubber and ac input filter are presented. The investigation result shows that IGCT type semiconductor devices generate the total efficiency of 97.74% under the rated condition.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.181-182
• /
• 2014

본 논문에서는 동기 정류 스위치를 사용한 임계 도통 모드 부스트 PFC 컨버터의 디지털 제어 기법을 제안한다. 상태 궤적 분석을 통해 입력전압 전 범위의 영전압 스위칭 조건을 구하였으며, 총 입력 전하 분석을 통하여 높은 역률을 위한 스위치 추가 온-타임을 도출하였다. 제안하는 제어 기법은 디지털 제어기를 이용한 $230V_{rms}$ 입력, 400V/200W 출력 프로토타입에서 타당성을 입증하였다. 그 결과 동기 정류기를 이용한 임계 도통 모드 부스트 PFC 컨버터는 높은 역률 및 효율을 갖는다.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.23-24
• /
• 2014

본 논문은 절연형 양방향 DC-DC 컨버터의 방전모드와 변압기 권선비에 따른 손실 분석에 대해 다루었다. Phase-Shift방전모드와 Boost방전모드에서 변압기 권선비에 따른 스위치손실을 분석하여 손실을 최소로 하는 변압기 권선비와 최적의 방전모드를 결정하고자 한다.