• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.565-575
• /
• 2009

In recent years, there have been numerous explosion-related accidents due to military and terrorist activities. Such incidents caused not only damages to structures but also human casualties, especially in urban areas. To protect structures and save human lives against explosion accidents, better understanding of the explosion effect on structures is needed. In an explosion, the blast load is applied to concrete structures as an impulsive load of extremely short duration with very high pressure and heat. Generally, concrete is known to have a relatively high blast resistance compared to other construction materials. However, normal strength concrete structures require higher strength to improve their resistance against impact and blast loads. Therefore, a new material with high-energy absorption capacity and high resistance to damage is needed for blast resistance design. Recently, Ultra High Strength Concrete(UHSC) and Reactive Powder Concrete(RPC) have been actively developed to significantly improve concrete strength. UHSC and RPC, can improve concrete strength, reduce member size and weight, and improve workability. High strength concrete are used to improve earthquake resistance and increase height and bridge span. Also, UHSC and RPC, can be implemented for blast resistance design of infrastructure susceptible to terror or impact such as 9.11 terror attack. Therefore, in this study, the blast tests are performed to investigate the behavior of UHSC and RPC slabs under blast loading. Blast wave characteristics including incident and reflected pressures as well as maximum and residual displacements and strains in steel and concrete surface are measured. Also, blast damages and failure modes were recorded for each specimen. From these tests, UHSC and RPC have shown to better blast explosions resistance compare to normal strength concrete.

• Journal of the Korean Society of School Health
• /
• v.5 no.2
• /
• pp.42-65
• /
• 1992

A survey was made of 976 students who were selected among students of 5 middle schools at Taegu so that it could furnish basic knowledge about sex education of adolescents by analyzing students recognition of sex, acquaintance with the opposite-sex, sex-education, The survery took a month from Nov. 1, to Nov 30, 1991. The results of this study are summarized as follows. 1. The general characteristics of the surveyed students. The survey consisted of 332 boys middle school student & 325 girls middle school students, 157 male & 162 female students of coeducational middle schools. 32.9% of them were from the first grade, 33.2% from the second grade & 33.9% from the third grade. 35.7% of them believed in Buddhism, 19% Christianism and the mode of their living standard, 86.7%, fell on 34.7% of their parents engaged in commerce and they were followed by salary man and public officals, 93.1 % of the students, parents were alive. 44.9% of their fathers were graduates of high school and 42.2% of their mothers middle school. 2. Sexual maturity 89.1 % of the surveyed girls had experienced menstruation. The mode of first menstruation, 48.2%, was at the age of 13 and the mean of it was 12.9, 3.7% the surveyed boys had exprienced a wet drem before. The mode of the first wet dream, 40.0%, was at the age of 14 and the mean was 13.4. 21.3% of surveyed students had the experience of masturbation but the number of girls fell far short of that boys. The mode of the first masturbation, 37.0%, was at the age of 14 and the mean was 13.4. 3. The acquaintance and sexual relations with the opposite sex 1) Analyzing the students actual conditions with the opposite, I found out that 52.3% of them wanted to have any kind of relations with the opposite and that 30.25 had already had some kind of relations. 73.2% of the students having relations with the opposite thought the other sex merely as a friend and the number of students who were thinking that way was distributed evenly among schools. 28.8% of the students had got acquainted with the other sex through their frieds and there were not much difference between boys and girls in the method of getting acquainated with the opposite. About 35.2% of the students having relations with the opposite came from the third grade. 47.8% of them answered that the meeting place was not fixed and 26.4% answered that they were meeting their parthers outdoors. 60.7% replyed that they were not disturbed in their studies by the relations with the other sex. 2) Most of the students 79.4%, answered that they had never had sexual relations and 16.3% of the rest said that thery were expressing their feelings by grasping each other's hand. 3) 16.6% of the surveyed students asid that they had the exprience of smoking, 1.1 % of an illusion caused by inhaling chemical addhesives, 44.0% of drinking and 41.4% of warching pornographic films. 4. The knowledge and attitude about the sex 1) The distribution and analysis according to schools and grades : 64.8% of the surveyed students answered correctly to the questions about mensturation, 49.3 % did so about wet dreams, 94.3 % did so about conception, 60.6% did so about child birth, 73.9% did so about AIDS and 50.1 % did so about sexual diseases. Roughly speaking, they had not much knowledge of sexual diseases. 2) The recognition of sex according to schools and grades : 39.0% of the students said that they had worries about sex. 33.1 % of what they worried was concerned with their bodies and 26.8% was about the acqaintance and relationship with the opposite sex. The girls were much more concerned about the former and the boys the latter. 51.1 % of the students asid that they had no specific opinion of masturbation but 19.2% said that's alright if self-restrained. About the sexual intercourse before marriage, 75.7% said negatively. 5. The need for sex education most of the students, 99.4% said they needed sex education and there was not much difference in that thought among schools. And 49.7% answered that schools, families, and societies were equlally important in sex education. About half of the students, exactly 50.2%. considered it as the main reason of sex education to prevent accidents cauesd by ignorance of sex. 81.4% said that they had had some kind of sex education. Most of the educations, 87.0%, had taken place at schools but 5.2% said they were getting most of the knowledge about sex from therir friednds, juniors and seniors. 59.5% of the students who had ever had a sex education said "Just so, so" when asked of the level of their contentment but the number of students who said "satisfied" was only a few, 16.1 %. 20.7% of the survered answered that thery wanted sex education to be made in the course of home life, and 26.6 % of the students most wanted to know about the acquaintance and relationship with the oppostie sex, 29.0% preferred nurse teachers as proper councellors of sex education. The mode of their present councellors, 42.0%, was friends but only 7.6% answered they dicussed with teachers. 6. The correlation analysis between general characteristcs and sexual behaviors of the surveyed students revealed that sex had a signigicant(P<0.001) positive correlation with parents' love toward students(P<0.01), the experience of masturbation, smoking, an illusion caused by inhaling chemical adhesives and the experience of watching pornographic films. And the standard of living had a significant(P<0.01) positive correlation(P<0.01) with grade point average, parents' existence(P<0.01) and parents' love, but a significant(P<0.01) negative correlation with sexual worries. grade point average had a significant(P<0.01)negative correlation with the experience of an illusion caused by chemical adhesives(P<0.01) and smoking. Parents' existence had significant(P<0.01) positive correlations with parents' love and smoking but a significant(P<0.01) negative correlation with the experience of an illusion by chemical adhesives. There was a significant(P<0.01) negative correlations between parents' love and the experience of an illusion by chemical adhesives, and a significant(P<0.001) positive correlation among masturbation and sexual worries, smoking, an illusion by chemical adhesives and the experience of watching pornographic films. There was a significant(P<0.001) positive correlation among acquaintance with the opposite sex, smoking, the experience of an illusion by chemical adhesives and watching pornographic films. Sexual worries had significant(P<0.01) positive correlations with smoking, the experience of an illusion by chemical adhesives and watching pornographic films. smoking had a significant positive correlation with drinking the experirence of, an illusion by chemical adhesives and watching pornographic films. Finally, there was a significant(P<0.01) positive correlation between the drinking experience and the illusion experience by chemical adhesives. According to the results mentioned above, the fact is certain that there is a great need for sex education of adolescents. Therefore, it is desirable that the schools teach sexual physiology and normal positively and that sex education including hygien education be an independant course in the curriculums. Furthermore, it is essential that the schools should have enough nurse teachers to take up sex education, expand training opportunities for them and that they develop educational materials. Considering the unbalance of the level of sex educations between boys and girls, I want to suggest that all boys and girls have sex education evenly and lead happy lives by correction irrational thought about sex, that is to say, sex discrimination, Sex education programs, especially of middle school students, should be reexamined if it is to give the students effective and profitable knowledge about sex. In addition, the government should establish a policy of adolescents' sex education to have healthy opinions of sex settled nationwide.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.424-434
• /
• 2009

Statement of problem: Problems such as loosening and fractures of retained screws and fracture of implant fixture have been frequently reported in implant prosthesis. Purpose: Implant has weak mechanical properties against lateral loading compared to vertical occlusal loading, and therefore, stress analysis of implant fixture depending on its material and geometric features is needed. Material and methods: Total 28 of external hexed implants were divided into 7 of 4 groups; Group A (3i, FULL $OSSEOTITE^{(R)}$Implant), Group B (Nobelbiocare, $Br{\aa}nemark$ $System^{(R)}$Mk III Groovy RP), Group C (Neobiotec, $SinusQuick^{TM}$ EB), Group D (Osstem, US-II). The type III gold alloy prostheses were fabricated using adequate UCLA gold abutments. Fixture, abutment screw, and abutment were connected and cross-sectioned vertically. Hardness test was conducted using MXT-$\alpha$. For fatigue fracture test, with MTS 810, the specimens were loaded to the extent of 60-600 N until fracture occurred. The fracture pattern of abutment screw and fixture was observed under scanning electron microscope. A comparative study of stress distribution and fracture area of abutment screw and fixture was carried out through finite element analysis Results: 1. In Vicker's hardness test of abutment screw, the highest value was measured in group A and lowest value was measured in group D. 2. In all implant groups, implant fixture fractures occurred mainly at the 3-4th fixture thread valley where tensile stress was concentrated. When the fatigue life was compared, significant difference was found between the group A, B, C and D (P<.05). 3. The fracture patterns of group B and group D showed complex failure type, a fracture behavior including transverse and longitudinal failure patterns in both fixture and abutment screw. In Group A and C, however, the transverse failure of fixture was only observed. 4. The finite element analysis infers that a fatigue crack started at the fixture surface. Conclusion: The maximum tensile stress was found in the implant fixture at the level of cortical bone. The fatigue fracture occurred when the dead space of implant fixture coincides with jig surface where the maximum tensile stress was generated. To increase implant durability, prevention of surrounding bone resorption is important. However, if the bone resorption progresses to the level of dead space, the frequency of implant fracture would increase. Thus, proper management is needed.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.5 s.78
• /
• pp.561-568
• /
• 2005

The object of this paper is to determine appropriateness for use of high-strength tensile bar as a tension web member. The gap K-joint of tensile bar types were compared with gap K-joint of square hollow section (SHS) types. For the same width-to-thickness ratio ($2{\gamma}=33.3$ ), tests were performed on four specimens of the SHS type and eight specimens of the tensile bar type. The comparison of capacity with the experimental results showed a capacity of the SHS type joint to be higher than that of the tensile bartype joint for the same brace-to-chord width ratio. Moreover, the capacity of the SHS type joints increased proportionally to the width ratio ${\beta}$), while tensile bar type joints increased as the tension width ratio (${\beta}2$). In failure mode, SHS-type specimens showed local buckling of the compression brace and plastic failure was observed between the tension brace and chord face, and with the tensile bar type specimens there appeared punching shear failure of the chord face at the toe of the connection plate. It is, therefore, concluded that width-to-thickness ratio should be lower than that of the hollow-section type and the relation between tension and compression width ratio should be considered.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.291-302
• /
• 2009

A compression lap splice can be calculated longer than a tension lap splice in high strength concrete according to current design codes. New criteria for the compression lap splice including the effects of concrete strength are required for practical purpose of ultra-high strength concrete. Characteristics of compression lap splice have been extensively investigated and main parameters are derived. In addition, an experimental study has been conducted with column specimens in concrete strength of 40 and 60 MPa. The strength of the compression lap splice consists of bond and end bearing and two contributors are combined. Therefore, combined action of bond and end bearing should be assessed. Compared with tension splices, concrete strength significantly affects the strength of compression splices due to short splice length and existence of end bearing. Test results show that the splice strength can be evaluated to be proportional to square root of compressive strength of concrete. The stress states of concrete surrounding spliced bars govern the strengths of bond and end bearing. Because the axial stress of the concrete is relatively high, the splice strength is not dependent on clear spacing. End bearing strength is not affected by splice length and clear spacing and is expressed with a function of the square root of concrete strength. The failure mode of specimens is similar to side-face blowout of pullout test of anchors and the strength of end bearing can be evaluated using the equation of side-face blowout strength. Because the stresses developed by bond in compression splices are nearly identical to those in tension splices, strength increment of compression splices is attributed to end bearing only.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.9
• /
• pp.3915-3920
• /
• 2014

Background: Hepatocellular carcinoma (HCC) is a dismal tumor with a high incidence, prevalence and poor prognosis and survival. Management of HCC necessitates multidisciplinary clinics due to the wide heterogeneity in its presentation, different therapeutic options, variable biologic behavior and background presence of chronic liver disease. We studied the different prognostic factors that affected survival of our patients to improve future HCC management and patient survival. Materials and Methods: This study is performed in a specialized multidisciplinary clinic for HCC in Kasr El Eini Hospital, Cairo University, Egypt. We retrospectively analyzed the different patient and tumor characteristics and the primary mode of management applied to our patients. Further analysis was performed using univariate and multivariate statistics. Results: During the period February 2009 till February 2013, 290 HCC patients presented to our multidisciplinary clinic. They were predominantly males and the mean age was $56.5{\pm}7.7years$. All cases developed HCC on top of cirrhosis that was mainly due to HCV (71%). Most of our patients were Child-Pugh A (50%) or B (36.9%) and commonly presented with small single lesions. Transarterial chemoembolization was the most common line of treatment used (32.4%). The overall survival was 79.9% at 6 months, 54.5% at 1 year and 22.4% at 2 years. Serum bilirubin, site of the tumor and type of treatment were the significant independent prognostic factors for survival. Conclusions: Our main prognostic variables are the bilirubin level, the bilobar hepatic affection and the application of specific treatment (either curative or palliative). Multidisciplinary clinics enhance better HCC management.

• Journal of Korean Society of Transportation
• /
• v.29 no.4
• /
• pp.29-41
• /
• 2011

This study investigates the factor that influences commuting time to work when individuals allocate their time for different types of activities. The commuting time is an important indicator for an individual to determine the residence and choose the means of transportation. The analysis uses the data collected from people who live in Seoul metropolitan area including Seoul, Incheon and Gyeonggi Province, and commute to work and making the simple linkage travel (home-work-home) within the area. For the analysis, the Cox hazard proportional methodology was adopted. The method is known to be well applied without assuming any distribution in case of the dependent variable being continuous. For the covariate, the interaction effect between the space variable of the work place and the variable of transportation has been also included in the model. The commuting time to work has been estimated for both 1) the whole metropolitan area and 2) the separate regions i.e., Seoul, Incheon and Gyeonggi-Do. The result reveals that characteristic variables related to individual, household and travel properties influence the mode of transportation and the time allocated for commuting to work (p<0.01). This study also demonstrates the usefulness of the Cox hazard proportional model. The data used in this study is the actual household travel data surveyed in 2006 in the metropolitan area, and analyzing the survey data in 2010 is currently in progress. Comparison of the two survey data sets seeking any behavioral change is suggested for the future study.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.11
• /
• pp.35-49
• /
• 2020

The lateral bearing capacity of the micropile depends on the installed conditions such as number, installation angle and spacing of the pile. Existing research on micropile has been limited to the evaluation of vertical bearing characteristics and suggestion of effective installation methods, and there are few studies on failure mechanisms such as failure mode. And most of the studies on the lateral bearing capacity of micropile are also on the 1-row micropile. Therefore, in this study, a model test was performed to evaluate the behavior and lateral bearing characteristics of a 2-row micropile when the installed conditions such as the installation length, angle, and spacing of the pile were different. As a result of the model test, when the installation angle is θ > 0° (Not cross installation), the lateral bearing capacity of 2-row micropile depends on the spacing of the piles, and the installation angle θ = +30° was the most effective for increasing the bearing capacity. In addition, when the installation angle is θ < 0° (Overlap installation), it depends on the spacing and angle of the pile, and the condition of installation angle θ = -15° was found to be the most effective for increasing the bearing capacity.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.385-391
• /
• 2011

The time-dependent density functional theory (TDDFT) method has been carried out to investigate the excitedstate hydrogen-bonding dynamics of phenol-$(H_2O)_2$ complex. The geometric structures and infrared (IR) spectra in ground state and different electronically excited states ($S_1$ and $T_1$) of the hydrogen-bonded complex have been calculated using the density functional theory (DFT) and TDDFT method. A ring of three hydrogen bonds is formed between phenol and two water molecules. We have demonstrated that the intermolecular hydrogen bond $O_1-H_2{\cdots}O_3-H$ of the three hydrogen bonds is strengthened in $S_1$ and $T_1$ states. In contrast, the hydrogen bond $O_5-H_6{\cdots}O_1-H$ is weakened in $S_1$ and $T_1$ states. These results are obtained by theoretically monitoring the changes of the bond lengths of the hydrogen bonds and hydrogen-bonding groups in different electronic states. The hydrogen bond $O_1-H_2{\cdots}O_3-H$ strengthening in both the $S_1$ and $T_1$ states is confirmed by the calculated stretching vibrational mode of O-H (phenol) being red-shifted upon photoexcitation. The hydrogen bond strengthening and weakening behavior in electronically excited states may exist in other ring structures of phenol-$(H_2O)_n$.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.3
• /
• pp.51-56
• /
• 2015

It has been used various pad finish materials to enhance the reliability of solder joint and recently Electroless Ni Electroless Pd Immersion Gold (the following : ENEPIG) pad has been used more than others. This study is about reliability according to being used in commercial Electrolytic Ni pad and ENEPIG pad, and was observed behavior of various Cu contents. After reflow, the inter-metallic compound (IMC) between solder and pad is composed of $Cu_6Sn_5$ (Ni substituted) by using EDS, and in case of ENEPIG, between IMC and Ni layer was observed the dark layer ($Ni_3P$ layer). Additional, it could be controlled the thickness of dark layer according to Cu contents. Investigated the different fracture mode between electrolytic Ni and ENEPIG pad after drop shock test, in case of soft Ni, accelerated stress propagated along the interface between $1^{st}$ IMC and $2^{nd}$ IMC, and in case of ENEPIG pad, accelerated stress propagated along the weaken surface such as dark layer. The unstable interface exists through IMC, pad material and solder bulk by the lattice mismatch, so that the thermal and physical stress due to the continuous exterior impact is transferred to the IMC interface. Therefore, it is strongly requested to control solder morphology, IMC shape and thickness to improve the solder reliability.