• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3790-3794
• /
• 2013

Molecular dynamics simulations were performed to study the structure and stability of a nanoscale self-assembled monolayer (SAM) of alkanethiol on a gold (111) surface. The tilt angle and orientational order of the alkyl chains in the SAM island were examined by systematically varying the size of the island. The chain length dependence of the SAM island was examined by considering alkanethiols containing 12, 16, 20, and 24 carbon atoms. The minimum diameter of SAM islands made from 1-tetracosanethiol, 1-ecosanethiol, 1-hexadecanethiol and 1-dodecanethiol were 2.29, 1.9, 4.7 and 4.76 nm, respectively. These set the ultimate resolution that can be patterned by soft nanolithography. As the length of alkanethiol increases, the SAM islands became more ordered in both orientation and conformation of the alkyl chains.

• 전자공학회논문지D
• /
• 제34D권4호
• /
• pp.33-39
• /
• 1997

The crystallization temperature of an amorphous silicon (a-Si) can be lowered down to 400.deg. C by a new method : Double-metal induced lateral crystallization (DMILC). The a-Si film was laterally crystallized from Ni and Pd deposited area, and its lateral crystallization rate reaches up to 0.2.mu.m/hour at that temperature and depends on the overlap length of Ni and Pd films; the shorter the overlap length, the faster the rate. Poly-Silicon thin film transistors (poly-Si TFT's) fabricated by DMILC at 400.deg. C show a field effect mobility of 38.5cm$^{3}$/Vs, a minimum leakage current of 1pA/.mu.m, and a slope of 1.4V/dec. The overlap length does not affect the characteristics of the poly-Si TFT's, but determines the lateral crystallization rate.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.83-91
• /
• 1996

This paper investigates the energy absorption characteristics of thin-walled rectangular tubes. In the compact mode, the crushing process of a thin-walled tube is analyzed into 3 parts by the ratio of outward to inward fold length. The mean crush load and the half-wave folding length are determined by using minimum energy principle. The effective crush distance can be determined when half-wave folding length is known, and the number of folds is derived when crush distance is given. Thus when the crush distance is given, energy absorption capacity can be estimated with mean crush load and number of folds. And the theoretical value is proven experimentally.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.491-492
• /
• 2008

This paper describes the series-gap characteristics of transmission line arrester with switching and lightning impulse flashover test. The transmission line arrester exhibited external gap because it is must not flashover with switching impulse on the other hand it is must flashover with lightning impulse. In accordance, minimum and maximum length of series-gap was determinated with these tests. As gap length is increased flashover voltage was increased in the range of 315.4 kV~496.3 kV and negative polarity exhibited a high voltage. As a result, It was thought tat the series-gap length of transmission line arrester exhibited in the range of 580 mm~1100 mm.

• 대한산업공학회지
• /
• 제22권3호
• /
• pp.351-364
• /
• 1996

This paper presents on EMQ model which determines an optimal production run length in a deteriorating machine. It is assumed that a machine is subject to a random deterioration from an in-control state to an out-of-control state with on arbitrary distribution and thus producing some proportion of defective items. An optimal production run length and a minimum average cost are derived in each of three deteriorating processes; constant, linearly increasing, and exponentially increasing. The model with repair cost is also analyzed. Several mistakes in previous research are found and discussed. Numerical experiments are carried out to see the behavior of the proposed model depending on the cost factors as well as machine parameters, and some interesting behaviors are observed.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.2
• /
• pp.243-246
• /
• 2006

This study investigates the improvement in the theoretical success rate of the integer ambiguity resolution in GPS/GNSS carrier-phase positioning by using many visible satellites. It estimates the dependence of the rate on the baseline length in relative positioning under the condition of the use of double/triple-frequency navigation signals. The calculation results show that the use of 14 navigation satellites (i.e., seven GPS and seven Galileo ones) remarkably improves the success rate under the condition of very short baseline length, compared with the use of seven GPS ones. The numerical reliability of the calculated success rates is strictly tested by examining the tightness of the union and minimum-distance bounds to the rate. These bounds are also shown to be effective to investigate the realization of the high success rates.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.484-485
• /
• 2007

This paper describes the series-gap characteristics of transmission line arrester with switching and lightning impulse flashover test. The transmission line arrester exhibited external gap because it is must not flashover with switching impulse on the other hand it is must flashover with lightning impulse. In accordance, minimum and maximum length of series-gap was determinated with these tests. As gap length is increased flashover voltage was increased in the range of 315.4 kV~496.3 kV and negative polarity exhibited a high voltage. As a result, It was thought tat the series-gap length of transmission line arrester exhibited in the range of 580 mm~1100 mm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.432-435
• /
• 2000

This paper present a new sort of multilayer piezoelectric ceramic transformer for the application to AC-adapters. This piezoelectric transformers operate in the second and third length extensional vibration mode. And the output performance of two types of piezoelectric transformers are compared by ANSYS, which is one of the FEM analysis program. As a result the minimum displacement was occurred at the two points in second length extensional vibration mode and three point in third length extensional vibration mode. One is the middle of input and the other is middle of output parts. And output voltage was inversely decreased by increasing number of output layers. Also The third mode type is shown higher power transition ratio than the second mode type.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.49-55
• /
• 2011

For the purpose of the enhancement of the air conditioner performance and fuel effciency, several cases of centrifugal impeller for passenger car air conditioner have been numerically analyzed by changing central angle of blades and length of outlet for shape optimization of the impeller. Commercial CFD program Fluent 6.3.26 has been used to compute velocity, temperature, pressure and turbulence intensity that can lead numerous results. The central angles of two blades and three cases of outlet length led 4~12% and 3.5~6.4% differences of velocity and flow rate, respectively. The velocity distribution near the blade surface was axisymmetric and had a maximum value of 22.19 m/s and velocity of the vertical direction of the impeller showed linear increase with horizontal direction. At case 3 of oultet length, there existed a a minimum pressure value of -133320 Pa.

• 한국가시화정보학회지
• /
• 제19권1호
• /
• pp.12-17
• /
• 2021

A three-dimensional slope valve component is used for controlling micro volume of liquid on a centrifugal force-based microfluidic disk platform, also called a lab-on-a-disk. The modeling factor of the slope valve component is determined to centrifugal force for liquid passing the crest of a slope valve via variation of slope length and angle as well as the radius to start point of slope valve. The centrifugal force is calculated by the equilibrium equation of the capillary and gravitational forces according to the microchannel surface roughness and the liquid volume, respectively. As a result, the slope valve is analyzed by the minimum angular velocity for liquid passing at crest point and the ratio between the length of micro liquid and slope length to obtain the factors for optimal slope angle modeling.