• Progress in Superconductivity
• /
• 제11권2호
• /
• pp.106-111
• /
• 2010

Sapphire resonators with $YBa_2Cu_3O_{7-\delta}$ (YBCO) endplates have provided a way to realize extremely high quality factor due to the extremely low dielectric loss of sapphire and conductive loss of YBCO films, which enables to measure the low surface resistance of superconductor films at microwave frequencies. We present microwave properties of HTS sapphire resonators designed for measuring the surface resistance of HTS films at millimeter-wave frequencies by using the two-resonance mode dielectric resonator method. Despite enhanced surface resistance ($R_S$) of YBCO films due to the quadratic frequency dependence of the $R_S$, the unloaded quality factor ($Q_0$) of the $TE_{021}$ mode sapphire resonator still appears to be well above $1\;{\times}\;10^6$ at a mm-wave frequency of 38 GHz at 10 K. However, it appears that the $TE_{012}$ mode $Q_0$ is unexpectedly low despite that the corresponding resonance peak looks uncoupled with parasitic modes. We discuss possible reasons for the unexpected results using the surface resistance at the $TE_{021}$, $TE_{012}$, and $TE_{011}$ mode frequencies.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2003년도 High Temperature Superconductivity Vol.XIII
• /
• pp.29-29
• /
• 2003

• ETRI Journal
• /
• 제39권3호
• /
• pp.336-344
• /
• 2017

In this paper, we propose a convenient microwave orbital angular momentum (OAM) mode generation and multiplexing method operating in the 18 GHz frequency band, based on a $2{\times}2$ uniform circular array and a $4{\times}4$ Butler matrix. The three OAM modes -1, 0, and +1 were generated and verified using spatial S-parameter measurements; the measured back-to-back mode isolation was greater than 17 dB in the full 17 GHz to 19 GHz range. However, the radiated OAM beam centers were slightly dislocated and varied with both frequency and the mode index, because of the non-ideal characteristics of the Butler matrix. This resulted in mode isolation degradation and transmission distance limitations.

• 전기학회논문지P
• /
• 제58권3호
• /
• pp.334-338
• /
• 2009

In this paper, We report the miniaturization of superconducting microwave power dividers based on lumped element equivalent circuits. To do this, we analyzed a conventional branch-type power divider by using an ABCD matrix under even and odd mode excitation. Then, we calculated each lumped element impedance throughout this analysis of a transmission line matrix. Also we simulated our equivalent circuits made of lumped elements by using a full wave analysis, em Sonnet. Our deign of microwave power divider based on simulated results was fabricated on high-$T_c$ superconducting thin films deposited on MgO substrate. Experimental results were reported in terms of bandwidth, center frequency, and phase difference between $S_{21}$ and $S_{31}$. We confirm that our design will be useful in the future microwave power systum.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권2호
• /
• pp.85-91
• /
• 2002

A novel multi-section power divider configuration is Proposed to obtain wide-band frequency performance up to microwave frequency region. Design procedures for the proposed microwave broadband power divider are composed of a Planar multi-section three-Ports hybrid and a waveguide transformer design procedures. The multi∼section power divider is based on design theory of the optimum quarter- wave transformer Furthermore, in order to obtain the broadband isolation performance between the two adjacent output ports, the odd mode equivalent circuit should be matched by using the lossy element such as resistor. The derived design formula for calculating these odd mode∼matching elements is based on the singly terminated filter design theory. The waveguide transformer section is designed to suppress the propagation of the higher order modes such as waveguide modes due to employing the metallic electric wall. Simulation and experiment show excellent performance of multi section power divider.

• 한국군사과학기술학회지
• /
• 제6권2호
• /
• pp.73-82
• /
• 2003

For measurements and analysis of dielectric characteristics of planar slabs of microwave absorbing materials, I have applied a free-space method in the frequency range of 8~14 GHz. The measurement system for free-space method consists of transmit and receive antennas, mode transitions, precision coaxal cables, the network analyzer, and a computer Special Spot-focused horn lens antenna was used to eliminate diffraction effects. Diffraction effects at the edges of the sample are minimized by satisfying the condition for minimum transverse dimension of the plate and the beamwidth of the antennas at the focus. The time-domain gating feature of the network analyzer and the thru, reflect, and line(TRL) calibration technique were used to eliminate the effects of undesirable multiple reflections. The complex coefficients of reflection and transmission, $S_{11}$ and $S_{21}$, of planar samples were measured for standard materials such as Teflon, Rexolite$\textregistered$ 2200. The results were compared with existing measurement method. And I applied a free-space method for measurement to measure dielectric constants of some electromagnetic absorbing materials. Dielectric properties for the same samples were also measured with a 7mm coxial transmission line method for purposes of comparison with the free-space method.

• 전기학회논문지
• /
• 제64권4호
• /
• pp.567-572
• /
• 2015

Discharge characteristics of linear microwave plasma were investigated by using fluid simulation of 2D axis-symmetry based on finite elements method. The microwave power was 2.45 GHz TEM mode and transmitted through linear antenna. Resistive power and pressure were considered simulation variables and argon was used for working gas. A decrease of electron density along the quartz tube was observed in low power condition but relatively uniform plasmas were generated in chamber by increasing the resistive power. The electron temperature was highly detected near the surface of quartz tube because the electron was heated only dielectric surface. The power transmission efficiency decreased and characteristics of surface plasma were observed in high electron density condition.

• 한국정보통신학회논문지
• /
• 제7권8호
• /
• pp.1621-1628
• /
• 2003

본 논문에서는, 마이크로스트립 회로의 패키징에서 고차모드 전파를 억제할 수 있는 유도성 격벽구조를 설계한다. 마이크로파 패키징은 회로를 외부의 물리적, 전기적 환경으로부터 격리$.$보호하기 위해 필요한 반면에, 동작 주파수가 증가함에 따라 하우징에 의한 고차모드가 발생하는 문제점을 내포하고 있다. 즉, 특성임피던스 및 실효유전율에 대한 영향을 줄이기 위해서는 패키징 크기가 가능한 커야 하지만, 패키징을 통과할 수 있는 고차모드의 차단 주파수를 높이기 위해서는 패키징 크기가 가능한 작아야 한다. 본 논문에서 제안된 유도성 격벽 패키지는 기존의 용량성 격벽 패키지에 비하여 고차모드 전력전달 억제계수$({S_21})$가 30㏈ 더 개선되었으며, 고차모드의 전달을 효과적으로 억제함으로써, 송수신 모듈과 같은 마이크로파 시스템 패키지화(System­in­a­Package) 설계에 유용하게 활용될 수 있다.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.156-160
• /
• 2012

Recently WCDMA signal transmission technology by large output microwave antenna have showed reduction of human resources and operating expense. But the existing antenna brackets cost is very expensive also its structure and functions are complicated. Unit brackets, suspending some sensors, subjected to acceleration loads, often fail due to self-vibration. To prevent such failures, it is necessary to understand the fatigue failure mode and to evaluate the fatigue life using tests or analysis techniques. The objective of this study is to develop the component test specifications, which are applicable to predict fatigue life at initial product design step, for unit brackets using vibration fatigue technique. So its application is limited to installation and management. In this project, we studied about more convenient bracket for microwave antennas through improvement on the existing antenna bracket's shortcoming and could develop an improved universal antenna bracket system for simple installation and application.

• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.143-151
• /
• 2007

Accurate measurements of the microwave surface resistance (Rs) of high temperature superconductor (HTS) films are important with regard to applications of HTS materials for wireless communications. As the surface resistance values of HTS films are usually extracted from the measured unloaded quality factor ($Q_0$) of resonators made of HTS films, it is essential to measure the resonator $Q_0$ with accuracy. The $TE_{011}\;mode\;Q_0$ of sapphire resonators with the endplates made of $YBa_2Cu_3O_{7-{\delta}}$(YBCO) film on $LaAlO_3$ is measured by using the S-parameter circle-fit method at a frequency of about 19.6 GHz and temperatures of 30 K to 90 K, which is compared with the measured values by using the Lorentzian-fit method. Good agreements are found between the two sets of $Q_0$ values measured by using the two different methods whether the resonator is used in a weak-coupling scheme or a strong-coupling scheme, showing reliability of both methods fur measuring the resonator $Q_0$ accurately. The $Q_0$ of sapphire resonators with a gap between the top plate and the rest of the resonator is also discussed.