• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5460-5466
• /
• 2014

본 연구에서는 실생활에 많이 이용되며 주로 주방용 식기 및 식칼, 소형칼, 주방 가위 등으로 널리 사용되는 STS420J2를 실험소재로 사용하였다. 마르텐사이트계 스테인리스강은 Cr13%이상 함유하고 있어 약 $1,050^{\circ}C$를 정점으로 하여 그 이상의 고온에서는 저하하는 단점을 가지고 있다. 실험에 사용되는 시험편 표면에 표면경화를 수행하기 위하여 #200 ~ #1500의 순서대로 미세연마 후 거친연마 가공을 실시하였으며, 다이오드 레이저의 표면경화 열처리 후에 자기냉각효과를 고려하여 $100{\times}50{\times}10$의 판재로 시험편을 제작하여 실험하였다. 소재 표면에 다이오드 레이저를 이용하여 국소부위에 표면경화 열처리를 수행하였다. 이때 다이오드 레이저의 출력과 이송속도를 공정조건으로 하여, 미세경도시험, 미세조직시험, 전자 주사 현미경(SEM), 입열량을 분석하였다. 분석 후에는 실험소재의 기계적 특성을 비교하여, 타 표면경화법에 비해 다이오드 레이저를 이용하였을 때의 표면경화 열처리 신뢰성과 우수함 그리고 최적의 공정조건을 도출하였다. 열처리 후 경화부는 Plate martensite로 경화 되었으며. 경도값은 Hv606.2로 열처리 후 약 3배 이상 표면경도가 향상되었다.

• 한국분말재료학회지
• /
• 제18권6호
• /
• pp.552-561
• /
• 2011

This study attempted to manufacture a Cu-15 at.%Ga coating layer via the cold spray process and investigated the effect of heat treatment environment on the properties of cold sprayed coating material. Three kinds of heat treatment environments, $5%H_2$+argon, pure argon, and vacuum were used in this study. Annealing treatments were conducted at $200{\sim}800^{\circ}C$/1 hr. With the cold sprayed coating layer, pure ${\alpha}$-Cu and small amounts of $Ga_2O_3$ were detected in the XRD, EDS, EPMA analyses. Porosity significantly decreased and hardness also decreased with increasing annealing temperature. The inhomogeneous dendritic microstructure of cold sprayed coating material changed to the homogeneous and dense one (microstructural evolution) with annealing heat treatment. Oxides near the interface of particles could be reduced by heat treatment especially in vacuum and argon environments. Vacuum environment during heat treatment was suggested to be most effective one to improve the densification and purification properties of cold sprayed Cu-15 at.%Ga coating material.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.1620-1625
• /
• 2015

본 연구에서는 산업현장에서 각종 기어나, 축, 체인, 롤러, 금형, 자동차강판 등으로 널리 쓰여 지는 기계구조용 탄소강인 SM45C를 실험소재로 사용하였다. 실험에 사용되는 시험편 표면에 표면경화를 수행하기 위하여 #200 ~ #1500의 순서대로 미세연마 후 거친연마의 연마가공을 실시하였으며, 다이오드 레이저의 표면경화 열처리 후에 자기냉각효과를 고려하여 $100{\times}50{\times}10$의 판재로 시험편을 제작하여 실험하였다. 소재 표면에 다이오드 레이저를 이용하여 국소부위에 표면경화 열처리를 수행하였다. 이때 다이오드 레이저의 출력과 이송속도를 공정조건으로 하여, 미세경도시험, 미세조직시험, 전자 주사 현미경(SEM), 입열량을 분석하였다. 분석 후에는 실험소재의 기계적 특성을 비교하여, 타 표면 경화법에 비해 다이오드 레이저를 이용하였을 때의 표면경화 열처리 신뢰성과 우수함 그리고 최적의 공정조건을 도출하였다. 열처리 후 경화부는 판상 마르텐사이트로 경화 되었으며. 경도값은 Hv729.5로 열처리 후 약 2.3배 이상 표면경도가 향상되있는 것을 확인하였다.

• Progress in Superconductivity
• /
• 제6권1호
• /
• pp.64-68
• /
• 2004

We fabricated cube-textured Ni and Ni-W alloy substrates for coated conductors and characterized the effects of W addition on microstructure, mechanical strength, and magnetic properties of the substrate. Pure Ni and Ni-(2, 3, 5at.%)W alloys were prepared by plasma arc melting, heavily cold rolled and then annealed at various temperatures of $600-1300^{\circ}C$. The texture was evaluated by pole-figure and orientation distribution function (ODF) analysis. Mechanical properties were investigated by micro Vickers hardness and tension test. Ferromagnetism of the substrate was measured by physical property measurement system (PPMS). It was observed that Ni-W substrates had sharp cube texture, and the full-width at half-maximums (FWHMs) of in-plane texture was $^{\circ}$-5.57$4.42^{\circ}$, which is better than that of pure Ni substrate. In addition cube texture of Ni-W substrates was retained at higher temperature up to $1300^{\circ}C$. Microstructural observation showed that the Ni-W substrates had fine grain size and higher mechanical properties than the pure Ni substrate. These improvements are probably due to strengthening mechanisms such as solid solution hardening and/or grain size strengthening. PPMS analysis showed that addition of W effectively reduced saturation magnetization in applied magnetic field and Curie temperature.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.292-296
• /
• 2003

In an attempt to enhance phase transformation and homogenization of Mn-doped $FeSi_2$, mechanical alloying of elemental powders was applied. Cold pressing and sintering in vacuum were carried out to produce a dense microstructure, and then isothermal annealing was employed to induce a phase transformation to the $\beta$-$FeSi_2$semiconductor. Phase transitions in this alloy system during the process were investigated by using XRD, EDS and SEM. As-milled powders after 100 h of milling were shown to be metastable state. As-sintered iron silicides consisted of untransformed mixture of $\alpha$-$Fe_2$$Si_{5}$and $\varepsilon$-FeSi phases. $\beta$-$FeSi_2$phase transformation was induced by subsequent isothermal annealing at $830^{\circ}C$, and near single phase of $\beta$-$FeSi_2$was obtained after 24 h of annealing. Thermoelectric properties in terms of Seebeck coefficient, and electrical conductivity were evaluated and correlated with phase transformation. Seebeck coefficient electrical resistivity and hardness increased with increasing annealing time due to $\beta$ phase transformation.

• 보존과학연구
• /
• 통권29호
• /
• pp.65-90
• /
• 2008

This study examines the status and the physical features of Paraloid B-72 layers with examination of microstructure and analysis of organic matters. Paraloid B-72 layers were coated on samples from the colour layer of outer wall painting in Mireuk hall in Geumsan temple. On the basis of the previous examination result, it has made the samples which are similar to outer wall in Mireuk hall in Geumsan temple. The samples can be divided into two, one; 5% Paraloid B-72 coating and another is without coating. Then samples have been experimented under the compulsive environments of infrared radiation and immersion, thereafter compared the results of the damages and physical features between two samples. As a result of the comparison, the sample with Paraloid B-72 had more serious cracks, exfoliations and peeling layers than that of without Paraloid B-72. Otherwise, in the examination of ultraviolet radiation, the sample with Paraloid B-72 coating showed weaker physical properties, less density in structure of colour layer and less hardness in surface of colour layer than the sample without coating. The percentage of moisture content after the ultraviolet radiation was higher in the sample without Paraloid B-72 than the sample with Paraloid B-72 coating. Observing the conditions before the ultraviolet radiation, the sample with Paraloid B-72 coating demonstrated lower rate in moisture evaporation rate than the sample without Paraloid B-72. As a consequence, in examination of this samples, the change of physical features are increased in the sample with Paraloid B-72 coating than that without Paraloid B-72 when compulsive environment of heat, moisture and ultraviolet rays for a short term are imposed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.384-389
• /
• 2002

This study was aimed to evaluate the weldability and optimize the welding conditions for flash butt welding of 780MPa grade steel applied to the automotive bumper reinforcement. And then the relationship between the welding conditions and the joint performance relating specifically to coil-joining steel would be established. The effect of welding conditions between flashing and upsetting process was elucidated. Microstructure observation of the joint indicated that the decarburized band was mainly changed with upsetting process. Width of HAZ was also related to the upsetting conditions rather than the flashing conditions. Generally maximum hardness at HAZ was correlated with $C_{eq}$ of steel and the empirical relationship was obtained to estimate the HAZ properties. Tensile elongation at the joint was usually decreased with increasing the initial clamping distance. Investigation of fracture surface after tensile and bending tests reveal that the origin of cracking at the joint was oxide inclusions composed of $SiO_2$, MnO, $Al_2$ $O_3$, and/or FeO. The amount of inclusions was dependent on the composition ratio of Mn/Si in steel. If this ratio was above 4, the amount of inclusions was low and then the resistance to cracking at the joint was enough to maintain the joint performance. It was obtained that the flashing process influenced the conditions for the energy input to establish uniform or non-uniform molten layer, while the upsetting conditions influenced the joint strength. Heat input variable during flashing process was also discussed with the joint properties.

• 한국세라믹학회지
• /
• 제54권4호
• /
• pp.292-297
• /
• 2017

${\beta}-SiAlON$, based on its high fracture toughness, good strength and low abrasion resistance, has been adopted in several industrial fields such as bearings, turbine blades and non-ferrous metal refractories. In general, ${\beta}-SiAlON$ is fabricated by reactive sintering using expensive $Si_3N_4$ and AlN as starting materials. On the other hand, in this study, a cheaper ${\beta}-SiAlON$ starting powder synthesized by SHS was employed to improve price competitiveness compared to that of the reactive sintering process. ${\beta}-SiAlON$ ceramics with various content of the sintering additive $Y_2O_3$ up to 7 wt% were fabricated by conventional pressureless sintering at $1800^{\circ}C$ for 2 to 8 h under $N_2$ pressure of 0.1 MPa. The specimen with 3 wt% $Y_2O_3$ exhibited the best mechanical properties: hardness of 14 GPa, biaxial strength of 830 MPa, fracture toughness of $5MPa{\cdot}m^{1/2}$ and wear rate of about $3{\times}10^{-6}mm^3/N{\cdot}m$.

• 한국결정성장학회지
• /
• 제6권3호
• /
• pp.386-391
• /
• 1996

$Si_{3}N_{4}$에 평균입경이 270 nm인 SiC 분말을 0, 10, 20, 30, 40 vol% 첨가하여 고온 가압소결법으로 $Si_{3}N_{4}/SiC$ 초미립복합재료를 제조하였다. 소결후 기지상인 ${\alpha}-Si_{3}N_{4}$는 ${\beta}-Si_{3}N_{4}$로 상전이하였으며, 이차상인 ${\beta}-SiC$는 변화가 없었다. 소결조제의 첨가에 의한 입계결정상은 검출되지 않았다. SiC의 첨가량이 많아짐에 따라 $Si_{3}N_{4}$ 결정립성장은 억제되어 미세한 결정입이 나타났으며, 작은 임자는 기지상 임내에 큰 SiC는 임계에 존재하였다. SiC 첨가에 따라 파괴강도는 약간 증가후 감소하였으며, 파괴인성은 감소하였고, 경도는 직선적으로 증가하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.38-48
• /
• 1993

A study on friction welding of stainless steel bar(SUS431) to chrome molybdenum steel bar(SCM21) was accomplished experimentally through analysis for relations among friction welding conditions, tension test, hardness test, microstructure test and acoustic emission test. The results obtained are summarized as follows ; 1. Through friction welding of SUS431 bar to SCM21 bar, the optimum welding condition by considering on strength and toughness was found to be the range of heating time of 3-5 sec when the number of rotating speed of 2000rpm, heating pressure of 10kg/$mm^2$, and upsetting time of 4 sec. 2. Quantitative ralationship was identified between heating time($T_1$, sec) and tensile strength (${\sigma},\;kgf/mm^2$) of the friction welded joint and the relation equation is $\sigma$=52.62$T_1{^{0.06}}$. 3. Through AE test, quantitative relationship was confirmed between heating time($T_1$, sec) and total AE(N, counts) during welding, and the relation is computed as follows ; N=30413.6$e^{0.06T1}$. 4. It was confirmed that the quantitative ralationship exists between the tensile strength of the welded joints and AE cumulative counts. And the relation is computed as the following ; ${\sigma}$=16.37(ln N)- 116.4. 5. When ONZ=36500-41500 counts by $OT_1Z$=3~5sec, it was identified by experiment that the range of welded joint tensile strength is 55.6-57.7kgf/$mm^2$/ whose joint efficiency is more than 100%, and it was experimentally confirmed that the real-time nondestructive quality(strength) evaluation for the friction welded joints could be possible by acoustic emission technique.