• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1226-1235
• /
• 2016

For wearable health monitoring systems, a fundamental problem is the limited space for storing energy, which can be translated into a short operational life. In this paper, a highly efficient active voltage doubling rectifier with a wide input range for micro-piezoelectric energy harvesting systems is proposed. To obtain a higher output voltage, the Dickson charge pump topology is chosen in this design. By replacing the passive diodes with unbalanced-biased comparator-controlled active counterparts, the proposed rectifier minimizes the voltage losses along the conduction path and solves the reverse leakage problem caused by conventional comparator-controlled active diodes. To improve the rectifier input voltage sensitivity and decrease the minimum operational input voltage, two low power common-gate comparators are introduced in the proposed design. To keep the comparator from oscillating, a positive feedback loop formed by the capacitor C is added to it. Based on the SMIC 0.18-μm standard CMOS process, the proposed rectifier is simulated and implemented. The area of the whole chip is 0.91×0.97 mm², while the rectifier core occupies only 13% of this area. The measured results show that the proposed rectifier can operate properly with input amplitudes ranging from 0.2 to 1.0V and with frequencies ranging from 20 to 3000 Hz. The proposed rectifier can achieve a 92.5% power conversion efficiency (PCE) with input amplitudes equal to 0.6 V at 200 Hz. The voltage conversion efficiency (VCE) is around 93% for input amplitudes greater than 0.3 V and load resistances larger than 20kΩ.

• Journal of Biomedical Engineering Research
• /
• v.21 no.3 s.61
• /
• pp.255-260
• /
• 2000

This paper presents a radio-telemetry patient monitor. which is used for intensive cal?e units. emergency and surgical operation rooms to monitor continuously patients' vital signs. The radio-telemetry patient monitor consists of a vital sign acquisition unit. wireless data transmission units and a vital sign-monitoring unit. The vital sign acquisition unit amplifies biological signals, performs analog signal to serial digital data conversion using the one chip micro-controller. The converted digital data is modulated FSK in UHF band using low output power and transmitted to a remote site in door. In comparison with analog modulation. FSK has major advantages to improve performance with respect to noise resistance with fower error and the potential ability to process and Improve quality of the received data. The vital sign-monitoring unit consists of the receiver to demodulate the modulated digital data, the LCD monitor to display vital signs continuously and the thermal head printer to record a signal.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.501-512
• /
• 2018

Radio frequency identification (RFID) sensor tag provides several advantages including battery-less operation and low cost, which are suitable for long-term monitoring. This paper presents a self-powered RFID temperature sensor tag for online temperature monitoring in substation. The proposed sensor tag is used to measure and process the temperature of high voltage equipments in substation, and then wireless deliver the data. The proposed temperature sensor employs a novel phased-locked loop (PLL)-based architecture and can convert the temperature sensor in frequency domain without a reference clock, which can significantly improve the temperature accuracy. A two-stage rectifier adopts a series of auxiliary floating rectifier to boost its gate voltage for higher power conversion efficiency. The sensor tag chip was fabricated in TSMC $0.18{\mu}m$ 1P6M CMOS process. The measurement results show that the proposed temperature sensor tag achieve a resolution of $0.15^{\circ}C$/LSB and a temperature error of $-0.6/0.7^{\circ}C$ within the range from $-30^{\circ}C$ to $70^{\circ}C$. The proposed sensor tag achieves maximum communication distance of 11.8 m.

• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.369-374
• /
• 2008

A novel fiber optic surface plasmon resonance (SPR) sensor using cyclic olefin copolymer (COC) prism with the spectral modulation is presented. The SPR sensor chip is fabricated using the SU-8 photolithography, Ni-electroplating and COC injection molding process. The sidewall of the COC prism is partially deposited with Au/Cr (45/2.nm thickness) by e-beam evaporator, and the thermal bonding process is conducted for micro fluidic channels and optical fibers alignment. The SPR spectrum for a phosphate buffered saline (0.1.M PBS, pH.7.2) solution shows a distinctive dip at 1300.nm wavelength, which shifts toward longer wavelength with respect to the bovine serum albumin (BSA)concentrations. The sensitivity of the wavelength shift is $1.16\;nm{\cdot}{\mu}g^{-1}{\cdot}{\mu}l^{-1}$. From the wavelength of SPR dips, the refractive indices (RI) of the BSA solutions can be theoretically calculated using Kretchmann configuration, and the change rate of the RI was found to be $2.3{\times}10^{-5}RI{\cdot}{\mu}g^{-1}{\cdot}l^{-1}$. The realized fiber optic SPR sensor with a COC prism has clearly shown the feasibility of a new disposable, low cost and miniaturized SPR biosensor for biochemical molecular analyses.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2005.05a
• /
• pp.198-201
• /
• 2005

DNA microarray 칩은 신약 개발, 유전적 질환 진단, Bio-molecular 상호작용 연구, 유전자의 기능연구 등 폭넓게 사용되고 있다. 이 논문은 cDNA mimcroarray 데이터를 분석하기 위한 웹형태의 시스템 개발에 대한 내용을 다룬다. 하나의 cDNA microarray에는 수 백에서 수 만개의 유전자가 심어져 있으며, 데이터를 분석할 때 대량의 데이터와 다양한 형태의 오류로 인해서 데이터간의 차이를 보정하는 분석 도구와 통계적 기법들이 사용되어야 한다. 본 논문에서는 가상 칩 뷰어를 이용하여 실제 microarray 데이터의 foreground intensity에서 백그라운드의 intensity를 제거하여 일반화된 칩 이미지를 생성한다. 이 가상 칩 뷰어는 여러 가지 필터효과와 서로 다른 두 형광의 차이를 조정하는 global normalization 기법을 사용하여 발현 유전자 분석을 시각적으로 할 수 있고, 중복된 마이크로어레이 칩 데이터를 통하여 시간이 많이 걸리는 분석전 칩의 유효성을 검토할 수 있다. 칩 데이터의 normalization을 위한 통계 방법으로 R 통계 도구와 linear 모델을 사용하여 microarray 칩의 유전자 발현 양상을 분석한다. 통계적 방법을 사용하지 않은 데이터를 추출, 이 데이터의 패턴 그래프 그리고 발현 레벨을 분류하여 마이크로어레이의 각 스팟의 유효성 검토의 정확성을 높였다. 이 시스템은 칩의 유효성 검토, 스팟의 유효성 검토, 유전자 선정에 대해 분석의 용이성과 정확성을 높일 수 있었다.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.545-554
• /
• 2003

Design of the optical modulator composed of a three-waveguide coupler and CPW traveling-wave electrodes was carried out. Switching phenomena of three-waveguide couplers were analyzed by using the coupled mode theory, and the coupling-lengths of the devices were calculated by means of the FDM. CPW traveling-wave electrodes were analysed by the CMM and SOR simulation technique in order to find the conditions of phase-velocity and impedance matching. Traveling-wave modulators were fabricated on z-cut LiNbO$_3$ substrate. Ti was in-diffused in LiNbO$_3$ to make waveguides and Au electrodes were built on the waveguides by the electrolyte technique. The fabricated modulator chip was end-polished, pig-tailed and packaged in a brass mount with K-connector. The insertion loss and the switching voltage of the optical modulator were about 4㏈ and 19V, respectively. Network analyzer was used to obtain the S parameter and the corresponding RF response. From the measurement, parameters of the traveling-wave electrodes were extracted to be Z$_{c}$= 45 Ω, N$_{eff}$=2.20, and $\alpha$$_{0}$=0.055/cm√GHZ. The measured optical response R($\omega$) was compared with the theoretically estimated one, showing both responses agree well. The measurement results revealed that 3㏈ bandwidth turned out to be about 13 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.77-83
• /
• 2011

In this thesis, 50W Doherty amplifier was designed and implemented for Beyond 3G's repeater and base-station. Auxiliary amplifier of doherty amplifier was implemented by Gate bias control circuit. Though gate bias control circuit solved auxiliary's bias problem, output characteristics of doherty amplifier was limited. To enhance the output characteristic relativize Drain control circuit And To improve power efficiency make 3-way Doherty power amplifier. therefore, 3-way GDCD (Gate and Drain bias Control Doherty) power amplifier is embodied to drain bias circuit for General Doherty power amplifier. The 3-way GDCD power amplifier composed of matching circuit with chip capacitor and micro strip line using FR4 dielectric substance of specific inductive capacity(${\varepsilon}r$) 4.6, dielectric substance height(H) 30 Mills, and 2.68 Mills(2 oz) of copper plate thickness(T). Experiment result satisfied specification of amplifier with gains are 57.03 dB in 2.11 ~ 2.17 GHz, 3GPP frequency band, PEP output is 50.30 dBm, W-CDMA average power is 47.01 dBm, and ACLR characteristics at 5MHz offset frequency band station is -40.45 dBc. Especially, 3-way DCHD power amplifier showed excellence efficiency performance improvement in same ACLR than general doherty power amplifier.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.50-50
• /
• 1999

마이크로 공정을 이용한 초소형 정밀 기계는 공정 기술과 재료 기술의 발전에 의하여 더욱 소형화되고 있으며 특히 기능을 갖는 부분과 이 부분을 제어하는 주변회로의 on-chip화의 요구가 증가되기 시작하였다. 이와 같은 추세에 있어서의 문제점은 초소형 정밀기계 부품 소자의 구동을 위한 에너지원의 개발이다. 즉, 소자의 크기가 작아진 것에 부합되는 초소형의 전지가 필요하게 된 것이다. 따라서 보다 완전한 초소형 정밀 기계 및 마이크로 소자의 구현을 위하여 마이크로 소자와 혼성 (Hybrid) 되어 이용될 수 있는 고성능 및 초소형의 전지의 개발이 필수적이다. 초소형 전지의 구현을 위하여 Li계의 2차 전지를 선택하여 이를 박막화하고 반도체 공정을 도입할 수 있다. 이러한 전지를 박막형 2차 전지 또는 박막형 마이크로 전지(thin film Secondary Battery : TFSB or Thin Film Micro-Battery : TFMB)라 하며 이러한 2차 전지는 일반적인 벌크 전지와 동일하게 cathode/Electolyte/Anode의 구조를 갖는다. 박막의 특성상 전해질은 고상의 물질을 사용하는 것이 벌크형 2차 전지와 다른 점이다. TFSB의 성능은 주로 cathode에 의하여 결정되며 지금까지 많은 cathode 물질에 대한 연구 보고가 발표되고 있다. 반도체 공정을 이용한 TFMB의 제작시 무엇보다 중요한 점은 우수한 고상 전해질 및 anode 물질의 선택에 있다. 최근에 2차 전지를 위한 carbon계 anode를 대체할 수 있는 SnO에 대한 보고가 있는데 이는 한 개의 Sn 원자당 2개 이사의 Li가 반응하여 높은 용량을 갖는 전지의 제작이 가능하기 때문이다. Sno2의 anode는 매우 높은 충전용량을 갖는데 첫 번째 방전시에 Li2O를 생성하여 비가역적 반응을 나타내고 계속되는 충방전 동안 Li-Sn 합금이 생성되어 2차전지의 가역적 반응을 가능하게 한다. SnO2 는 대기중에서 Li 금속보다 안정하기 때문에 전지의 제작 공정 및 사용 면에서 매우 우수한 물질이지만 아직까지 SnO2 구조적 특성과 전지의 충, 방전 특성에 대한 관계의 규명을 위한 정확한 정설은 제시되고 있지 못하다. 본 연구에서는 TFSB anode 물질로써 SnOx박막을 상온에서 여러 전도성 콜렉터 위에 증착하여 그 충, 방전 특성을 보고하였다. 증착된 SnOx박막의 표면은 SEM, AFM으로 분석하였으며 구조의 분석은 XR와 Auger electron spectroscope로 하였다. 충, 방전 특성을 분석하기 위하여 리늄 foil을 대극과 참조 전극으로 하여 EC:DMC=1:1, 1M LiPF6 액체 전해질을 사용한 Half-Cell를 구성하여 100회 이상의 정전류 충, 방전 시험을 행하였다. Half-Cell test 결과 박막의 구조, 콜렉터의 종류 및 Sn/O비에 따라 서로 다른 충, 방전 거동을 나타내었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1393-1401
• /
• 2013

What is RFID Microchip tag attached to an object, the reader recognizes technology collectively, through communication with the server to authenticate the object. A variety of RFID tags, 13.56Mhz bandwidth RFID card, ISO/IEC 14443 standards based on NXP's Mifare tag occupies 72.5% of the world market. Of the Mifare tags, low cost tag Mifare Classic tag provided in accordance with the limited hardware-based security operations, protocol leaked by a variety of attacks and key recovery vulnerability exists. Therefore, in this paper, Cryptography Scheme and Secure Protocol for Safety Secure Scheme Construction in 13.56Mhz RFID have been designed. The proposed security scheme that KS generated by various fixed values and non-fixed value, S-Box operated, values crossed between LFSR and S-Box is fully satisfied spoofing, replay attacks, such as vulnerability of existing security and general RFID secure requirement. Also, It is designed by considering the limited hardware computational capabilities and existing security schemes, so it could be suit to Mifare Classic now.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.983-991
• /
• 2012

These days, agricultural products cultivated in facilities occupy the highest percentage of agricultural output price. Specifically cucumbers have been one of the crops that farmers prefer to growing, because their prices were high. However, cucumber crop is sensitive to the soil and environments and it requires the exact crop management. In order to establish cultivation techniques for cucumbers, the current situation of cucumber cultivation was surveyed from ten cucumber farmlands; five farmlands of cucumber cultivation in forcing and five of semi-forcing practicing systems, respectably. The soil conditions were alluvial or valley in soil topology, moderately or poorly drainage in soil drainage classes, coarse loamy in soil texture family. Soil was managed with deep plowing combined with application of basal fertilizers such as compost, rice straw, oil cake, wood chip and chemical fertilizer. The whole soil was prepared in uniformly with rotary. Three major nutrients ($N-P_2O_5-K_2O$)of basal application were 815-464-529 kg $ha^{-1}$ in forcing and 197-135-151 kg $ha^{-1}$ in semi-forcing cultivation. Top dressing of fertilizer was supplied in fertigation system of macro and micro elements in 2~3 day interval with water irrigation. The average yields of cucumbers were $168t\;ha^{-1}$ with 381,000 thousand won $ha^{-1}$ in average gross profit (AGP) in forcing cultivation and $115t\;ha^{-1}$ with 177,000 thousand won $ha^{-1}$ in AGP in semi-forcing cultivation. Cucumber production during the winter season was considered to increase the gross profit because cucumber price tends to stay in high level during this time. The accumulation of soil chemicals like EC, available $P_2O_5$ and exchangeable cations could be controlled by rice straw application. The rice straw application increased soil temperature during the winter season, in exchange of soil air, and in extension of plant roots. In addition, the rice straw application somewhat affected decrease of salts accumulation.