• Journal of Korean Society of Steel Construction
• /
• v.22 no.5
• /
• pp.477-485
• /
• 2010

Various monitoring sensors are used to predict and detect structural damage. Smart sensors, such as glass-fiber sensors, PZT, and MEMS, among others, have replaced traditional sensors. They are now being used in many areas. This study aims to predict the damage by measuring the PZT voltage attached on the specimen by the applied impact load. In the experiment to detect damages in beam connection, simple $H-400{\times}200{\times}8{\times}13$ beams were spliced with bolts. The results of FFT between PZT sensor and accelrometer were compared to measure the sensitivity of the PZT sensor. The damage to the beam was presumed by loosening the bolt, and then the damage measurement was accompanied. Secondly, a steel $PL600{\times}65{\times}5.8$ plate beam was fabricated for the purpose of experimenting on damage measurement. Impact loading test on three different locations was carried out. Damage width varied between 6~42mm on both sides by cutting, using a steel saw. The ratio of frequencies before and after the damage was computed to quantify the damage level by using FFT, and the change in mode pattern with the increased damage was investigated to measure the damage.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.466-473
• /
• 2020

Fabric current collector can be a promising electrode material for Capacitive Deionization (CDI) system that can achieve energy-efficient desalination of water. The one of the most attractive feature of the fabric current collector is its high tensile strength, which can be an alternative to the low mechanical strength of the graphite foil electrode. Another advantage is that the textile properties can easily make shapes by simple cutting, and the porosity and inter-fiber space which can assist facile flow of the aqueous medium. The fibers used in this study were made of woven structures using a spinning yarn using conductive LM fiber and carbon fiber, with tensile strength of 319 MPa, about 60 times stronger than graphite foil. The results were analyzed by measuring the salt removal efficiency by changing the viscosity of electrode slurry, adsorption voltage, flow rate of the aqueous medium, and concentration of the aqueous medium. Under the conditions of NaCl 200 mg/L, 20ml/min and adsorption voltage 1.5 V, salt removal efficiency of 43.9% in unit cells and 59.8% in modules stacked with 100 cells were shown, respectively. In unit cells, salt removal efficiency increases as the adsorption voltage increase to 1.3, 1.4 and 1.5 V. However, increasing to 1.6 and 1.7 V reduced salt removal efficiency. However, the 100-cell-stacked module showed a moderate increase in salt removal efficiency even at voltages above 1.5 V. The salt removal rate decreased when the flow rate of the feed was increased, and the salt removal rate decreased when the concentration of the feed was increased. This work shows that fabric current collector can be an alternative of a graphite foil.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.513-519
• /
• 2006

We developed two kinds of the microchip for application to electrophoresis based on both glass and quartz employing the MEMS fabrications. The poly-Si layer deposited onto the bonding interface apart from channel regions can play a role as the optical slit cutting off the stray light in order to concentrate the UV ray, from which it is possible to improve the signal-to-noise (S/N) ratio of the detection on a chip. In the glass chip, the deposited poly-Si layer had an important function of the etch mask and provided the bonding surface properly enabling the anodic bonding. The glass wafer including more impurities than quartz one results in the higher surface roughness of the channel wall, which affects subsequently on the microflow behavior of the sample solutions. In order to solve this problem, we prepared here the mixed etchant consisting HF and $NH_4F$ solutions, by which the surface roughness was reduced. Both the shape and the dimension of each channel were observed, and the electroosmotic flow velocities were measured as 0.5 mm/s for quartz and 0.36 mm/s for glass channel by implementing the microchip electrophoresis. Applying the optical slit with poly-Si layer provides that the S/N ratio of the peak is increased as ca. 2 times for quartz chip and ca. 3 times for glass chip. The maximum UV absorbance is also enhanced with ca. 1.6 and 1.7 times, respectively.

• Journal of Bio-Environment Control
• /
• v.23 no.2
• /
• pp.123-130
• /
• 2014

Oriental melon (Cucumis melo var. makuwa) should be cultivated on the soil and be harvested. It is difficult to find because it is covered with leaves, and furthermore, it is very hard to grip it due to its climbing stems. This study developed and tested oriental melon harvesting robots such as an end-effector, manipulator and identification device. The end effector is divided into a gripper for harvest and a cutter for stems. In addition, it was designed to control the gripping and cutting forces so that the gripper could move four fingers at the same time and the cutter could move back and forth. The manipulator was designed to realize a 4-axis manipulator structure to combine orthogonal coordinate-type and shuttle-type manipulators with L-R type model to rotate based on the central axis. With regard to the identification device, oriental melon was identified using the primary identification global view camera device and secondary identification local view camera device and selected in the prediction of the sugar content or maturity. As a result of the performance test using this device, the average harvest time was 18.2 sec/ea, average pick-up rate was 91.4%, average damage rate was 8.2% and average sorting rate was 72.6%.

• Food Science and Preservation
• /
• v.13 no.4
• /
• pp.438-444
• /
• 2006

This study was carried out to obtain fundamental data such as peeling efficiency and quality of potatoes and sweet potatoes peeled by hand, machine and alkali(NaOH). The weight loss by peeling was influenced by peeling methods. Weight losses by rotational brushing-type peeler showed the lowest value, 7.9% in potato, and 7.3% in sweet potato. Any significant differences in moisture content were not found in potatoes and sweet potatoes by peeling methods. The pH of potatoes and sweet potatoes just after peeling were 5.8-6.8 and 6.23-6.63, and decreased somewhat until 3 hrs after peeling. Hardness of potatoes and sweet potatoes peeled by hand with fruit knife were better than that of others. Depending upon the peeling method used the color and color differences undergo some changes in their color and browning. Color difference value of peeled potatoes by hand with a technical tools, and by mechanical peeler such as rotational cutting-type peeler and rotational brushing-type peeler showed just slightly. In particular, changes of rotor differences value of potatoes and sweet potatoes peeled by dipping with 10% NaOH solution at $100^{\circ}C$ was the highest in the samples peeled by NaOH.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.551-564
• /
• 2016

Earthworks are the fundamental steps in a construction job, and are mainly comprised of smaller tasks performed by construction machinery. The productivity of the construction job can be improved by optimizing excavation, filling, and other such operations. Earthworks involve a lot of mechanical work performed by the collaboration between various kinds of construction equipment, which in turn leads to higher fuel consumption. Actual earthworks depend mostly on the intuition and experience of the driver of the machines, thus leading to inefficiency and environmental problems caused by unnecessary emission of carbon, Recently automated and information-oriented technologies are consistently being researched towards the improvement of efficiency of earthworks in the construction industry. The present research involves the introduction and understanding of the decision-making elements of heuristics which can be applied to the earthwork planning. A method is also suggested for creating an effective work path for construction machine to perform task packages (TP) for cutting and filling processes. A simulation test is performed to verify the effectiveness of suggested methods in terms of space interference and total moving distance of construction equipment.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.14 no.1
• /
• pp.2535-2548
• /
• 1972

Instead of fertilizing the lands they moved to find other fertile lands and lived a feudal life agriculture and various machincs played a main role in the land reclamation. The best method of land clearing, the time and capacity in the operation and the effect of growing crops should systematically analized prior to the time of 3rd Five-year Economic Development(1972-1976) in order to cultivate 210,000ha of wasteland or the modernization of our country. The present study was investigated to find out a new working-system of mechanical land clearing and development of fertile soil. The results are as follows: 1) The first stage of productive power increases when weeds were mixed soil in the land clearing work in order to supply organic materials and to make soil swollen instead of burning or just removing. 2) The equipments such as bulldozers, harrows, power tillers and so on should be prepared in order to do a systematic work in the land clearing. 3) The work of pulling-up roots is dependent upon the forms of roots spreading under the ground. The work of the pulling-up of the straight roots was most difficult. But before the roots are pulling-up we do not know the forms of roots. 4) The cutting of soil from upside to under side land clearing method (II) Spent 6 hr 7 min 43 sec per 1 Danbo in doing land clearing and control method spent 4 hr 52 min 30 sec per 1 Danbo in doing land cearing. No significant difference could be found between II treatment type and I treatment type. 5) The volume of soil carried by bulldozer $270.38m^3$ per 1 Danbo in I type and in II type, $368.58m^3$ per 1 Danbo or about 36% increased in II type then in I type. But that is not a significant difference when considering the whole productive power of soil. 6) The land clearing of terrace by bulldozers cannot escape making the embankment slope of about $45^{\circ}$, and 25.3% should be decreased in the area. It is recommended to make use of the embankment slope by planting grass for cows. 7) The time of retary tilling increased 2.3 times or 1 hr 42 min 22 sec per 1 Danbo compared to the timesrequired in the harrowing. Because it mixed the Organic matter on ground and the harrowing of subsoil. 8) The havest of pasture growing on the land reclamation in natural slope is as follows. (a) The none fertilizers with reclaimed block of productivity decresed 1/10 than that of the farmland. Therefore the none fer tilizing in the cultivated pasture is unprofitable. (b) The havest of the manured IV treatment block was the best not only in the kinds of fertilizers but also in the kinds of pasture grass.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.10a
• /
• pp.39-41
• /
• 2011

The recycling rate of recovered paper in Korea is the highest in the world, 92%, but remanufacturing yield is low due to the extremely poor quality of the paper. The poor quality, in turn, influences to the reject amount in deinking process. To increase the yield of old newspaper recycling process, hydrophobic degree of inorganic pigments of deinking stock must be reduced. To determine the hydrophobicity, Pitch Potential Deposit Tester (PDT) was newly designed and applied with respect to the SB latex property of various quality used in Korea; its hydrophobic degree according to Tg, gel content, charge and particle size of latex and optimum designing condition of SB latex. And below are the conclusions: 1. The reason of excessive reject from old newspaper deinking process for total amount of printed ink is loss of inorganic pigments. When lipase, a biochemical catalyst, was applied with the purpose of preventing inorganic pigments loss about more than 70% of total reject weight and promoting hydration of pulp for deinking, deinking process yield of pre flotation secondary stage increased remarkably without any changes of deinking efficiency. 2. Lipase improved deinking stock by cutting ester linkage on surface of hydrophobic materials to promote its hydration. From this, it reached the conclusion that hydration degree of stock exercises significant effect on flotation deinking process yield. 3. Inorganic alkali promotes hydration of deinking stock. But there have been needs for more fundamental measures other than inorganic alkali of promoting hydration for yield improvement. For this, this study intended to find out reasons of chemical properties change on surface of hydrophobic material by change of pH. 4. Pitch Deposit Test (PDT) was performed for understanding principle of why surface of coating flake from OMG is hydrophobic and why it becomes hydrophilic when pH of stock is alkaline. As a result of this test, it is determined that swelling property by change of pH of latex film, which were used as coating adhesive is the reason for hydrophobic change. 5. Hydrophilicity of coating flake increased with hydrophilic pigments. And as more of SB Latex adhesive was used and higher of calcium hardness of stock became, its hydrophilicity decreased. SB Latex adhesive film is reformed by mechanical friction. For having hydrophilicity under neutral pH, strong bruising action such as kneading is required. 6. Because swelling of adhesive film decreases as Tg of SB latex gets lower and mean diameter gets smaller, it shows hydrophobicity under neutral pH. This lowers hydrophilicity of coating flake, which leads to easy elimination with flotation reject on DIP process. Therefore, for improving future flotation yield, it is necessary to develop to use eco-friendly clean SB latex by raising Tg and increasing mean diameter for recycling, and as a result, to reduce excessive loss of coating flake as a reject from deinking process.

• Journal of Korean Society of Forest Science
• /
• v.102 no.2
• /
• pp.239-246
• /
• 2013

This study observed changes of understory vegetation to evaluate the role of forest aggregate after 15% aggregated retention harvest in mature oak forest (> 100 years) in Gyungsangbukdo Bonghwagun in 2010 and 2011. Spontaneous responses of understory vegetation cover (%), species richness, abundance of plant growth forms (herbaceous and woody plants), and overall attributes (by Ordination analysis) were estimated in aggregate area (0.15 and n=36) and clear cut area (0.85 and n=192) in experimental site and control site (1 and n=300). Based on ordination analysis, overall change of species composition in aggregated sites were relatively lower than in harvest area. Right after treatment, total cover of cutted area slightly decreased from 15.6% to 14.7%, and species richness increased from 14 species to 22 species. Cover and richness in the both of aggregate and control sites increased. In plant growth forms, 15% aggregate harvest revealed positive effects on the abundance (cover and richness) of herbaceous plants than woody group. After retention treatment, overall, edge effect likely played major component of vegetation changes in aggregate forest and in harvested area, mechanical damage from harvest operation and change of forest structure by clear cutting were critical. As pre-treatment data, which are rare in ecological studies in Korea, were critical for interpretation between patterns that may have arisen from spatial distributions in the original forest, our experimental design have higher opportunity for long term monitoring on the effect of forest aggregate and vegetation regeneration in clear cutted area.

• Clean Technology
• /
• v.20 no.4
• /
• pp.439-448
• /
• 2014

The potential mitigation of greenhouse gas (GHG) is studied in the Pohang steel industrial complex (PHSIC). The total GHG emission in 2010 is estimated to be in the range from 4,174,000 to 4,574,000 $tCO_2-eq$ in PHSIC. To meet the target proposed by the government, it is needed to reduce 552,000 $tCO_2-eq$ at minium by 2020. To estimate the potential amount of GHG reduction, the technologies used in the voluntary carbon reduction projects are applied to 51 companies which are subject to GHG target management. From the viewpoint of technological availability and payback period, the fuel conversion and waste heat recovery have an advantage in the short term with a possibility to reduce 160,000 $tCO_2-eq$. In the mid term, the thermal technologies in steel and iron industry have the potential to cut 229,000 $tCO_2-eq$, while the electrical technologies have the potential of 125,000 $tCO_2-eq$ reduction. The gap between the target GHG mitigation and potential reduction using the short and mid term technologies is about 38,000 $tCO_2-eq$, which should be compensated by the fundamental process innovation and the implementation of the most cutting-edge technologies including renewable energy.