• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2005년도 한국우주과학회보 제14권1호
• /
• pp.138-142
• /
• 2005

위성자세제어용 구동기 인 반작용 휠은 축 방향 토크뿐만 아니 라 횡 축 방향 외 란 토크와 힘을 발생시켜 위성의 정밀 지향 안정성에 영향을 미치게 된다. 이를 위해서는 반작용 휠 구동시의 발생 외란을 정밀하게 측정할 필요가 있다. 그러나 반작용 휠의 구동은 측정테이블의 진동을 야기 시키고 테이블의 공진 주파수 영역에서 큰 측정 오차를 유발한다. 본 논문은 이러한 진동오차들을 줄이기 위하여 주파수 보정법에 의한 사후처리 과정을 제시하고, 이 보정법으로 얻어진 데이터들로부터 외란 파라미터를 결정함으로써 구동기 외란의 보다 정밀한 측정을 가능케 하기 위함이다. 이 보정법을 적용함으로써 구동기 외란 측정 주파수범위를 넓힐 수 있다.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.135-141
• /
• 2005

Measurement of five DOF motion errors in a ultra precision feed table was attempted in this study. Yaw and pitch error were measured by using a laser interferometer and roll error was measured by using the reversal method. Linear motion errors in the vertical and horizontal directions were measured by using the sequential two point method. In this case, influence of angular motion errors was compensated by using the previously measured ones by the laser interferometer and the reversal method. The capacitive type sensors and an optical straight edge were used in the reversal method and the sequential two point method. Influence of thermal deformation on sensor jig was investgated and minimized by the periodic measurement according to the variation of room temperature. Deviation of gain between sensors was also compensated using the step response data. 5 DOF motion errors of a hydrostatic table driven by the linear motor werer tested using the measurement method. In the horizontal direction, measuring accuracies for the linear and angular motion were within ${\pm}0.02\;{\mu}m$ and ${\pm}0.04$ arcsec, respectively. In the vertical direction, they were within ${\pm}0.02{\mu}m$ and ${\pm}0.05$ arcsec. From these results, it was found that the introduced measurement method was very effective to measure 5 DOF motion errors of the ultra precision feed tables.

• 한국정밀공학회지
• /
• 제4권4호
• /
• pp.36-42
• /
• 1987

Very accurate calibration is needed to index tables which are necessary for precision angle measurement. The repeatability of index table is less than 0.2 second, so that attentions should be paid to choosing devices to be used in the calibration of index tables. The auto- collimators have been used in the calibration of index tables, but the repeatability of auto- collimators is bad compared with that of index table. In place of autocollimators, we described a method which uses electric comparators which are possessed by most precision measurement laboratories. Electric comparators are set to measure small angle displacement without interrupting the rotation of index tables and the signals of two electric comparators are added to remove the run-out errors of the shafts of index tables. Two index tables have been calibrated simulataneously by this method and the measurement data have been analyzed by the least squares method. We compare the calibration results with those of methods using autocollimator and auto- matic autocollimator and are able to know that the data of electric comparator method lie between the data of autocollimator methods. The repeatability of measurement is less than 0.02 second. The electric comparator method is economical and capable of reducing the uncertainty of the measurement.

• Design & Manufacturing
• /
• 제13권4호
• /
• pp.51-56
• /
• 2019

Due to industrial development, the importance of GD&T tolerance is growing day by day. Roundness measurement means the size deviated from the ideal circle. Roundness evaluation methods include LSCI, MZCI, MCCI, and MICI. Generally, A is used a lot at industrial evaluation. In this experiment, we studied the variations in table velocity, filter values, and detector angles, which can cause errors in roundness measurements. The measurement conditions were table speeds of 10, 30 and 60 mm/s, probe angles of 10, 20 and 30 degrees and frequency filter settings of 15, 150 and 500 upr and The number of experiments was measured 30 and the average value was chosen as a representative value. The hypothesis test showed that the p-value for the frequency filter was greater than 0.05, and the experiment rejected the null hypothesis and adopted the alternative hypothesis.

• Smart Structures and Systems
• /
• 제14권6호
• /
• pp.1055-1079
• /
• 2014

Substructure shake table testing is a class of real-time hybrid simulation (RTHS). It combines shake table tests of substructures with real-time computational simulation of the remaining part of the structure to assess dynamic response of the entire structure. Unlike in the conventional hybrid simulation, substructure shake table testing imposes acceleration compatibilities at substructure boundaries. However, acceleration tracking of shake tables is extremely challenging, and it is not possible to produce perfect acceleration tracking without time delay. If responses of the experimental substructure have high correlation with ground accelerations, response errors are inevitably induced by the erroneous input acceleration. Feeding the erroneous responses into the RTHS procedure will deteriorate the simulation results. This study presents a set of techniques to enable reliable substructure shake table testing. The developed techniques include compensation techniques for errors induced by imperfect input acceleration of shake tables, model-based actuator delay compensation with state observer, and force correction to eliminate process and measurement noises. These techniques are experimentally investigated through RTHS using a uni-axial shake table and three-story steel frame structure at the Johns Hopkins University. The simulation results showed that substructure shake table testing with the developed compensation techniques provides an accurate and reliable means to simulate the dynamic responses of the entire structure under earthquake excitations.

• 기술혁신학회지
• /
• 제10권2호
• /
• pp.361-382
• /
• 2007

측정이란 측정기기를 가지고 계량하는 것을 의미하며, 측정표준 보급은 측정기기의 보급 및 확산과 밀접한 관계를 갖고 있다. 따라서 측정기기산업의 분석을 통하여 측정표준 보급의 영향을 살펴볼 수 있는 바, 본 연구에서는 측정기기의 산업부문별 생산유발기여도를 도출하여 산업구조 변화와의 관계를 분석하였다. 분석 결과에 의하면, 측정표준의 대용변수(Proxy variable)라고 할 수 있는 측정기기의 투입은 각 산업에 생산유발을 주고, 이러한 생산유발 기여가 해당 부문의 생산을 증가시키는데 기여하는 것으로 나타났다.

• 한국농공학회지
• /
• 제6권1호
• /
• pp.706-714
• /
• 1964

• 한국생산제조학회지
• /
• 제5권4호
• /
• pp.108-120
• /
• 1996

A new technique and theory are proposed which correct orientation of a cylinder to perform a reliable measurement of the surface profile. We analyze characteristics of machined surfaces, e.g., ground, lapped and turned surfaces. Based upon the results. the optimum correction technique is derived by the statistical method. To verify the techinques, measurements are carried out by using the contact stylus profilometer on a controllable table. The measurement shows that surface information of cylinders can be acquired with high accuracy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.675-676
• /
• 2008

• 한국소음진동공학회논문집
• /
• 제17권7호
• /
• pp.565-571
• /
• 2007

In the process of accurate manufacture and measurement, it is necessarily required to isolate external or internal vibration due to external disturbance and internal actuators. The higher vibration isolation system gets damping around resonance, the better it is generally. This paper analyzes the performance of an existing passive air-spring for vibration isolation table by using experiment and simulation. Optimal design for a passive air spring can be obtained by tuning the size of the orifice. Also design for an active isolation system is carried out by applying PID controller and considering non-linearity of pneumatic characteristics with help of look-up table. We have developed the active vibration isolation table with the better isolation performance.